Capillary Rheometer is a classic method of determining polymer melt viscosity. The test procedure is to date the best simulation of a polymer fabrication process. Melt undergoing a shear rate sweep and being extruded through a Capillary is found in extrusion, compounding and injection molding. The shear stress can be calculated from the pressure drop across measuring the flow rate. The pressure drop is determined from the plunger force, which is measured by a strain gauge load-cell with digital indication. TECHNICAL DATA :

display.

Type of Instrument	: Constant rate type.
Barral Bore Diameter	: 10 ± .005 mm.
Material of Barrel/Cylinder	: Tool steel.
Capillary Diameter	: Between 1 - 1.5 mm.
No. of Capillary	: 8 nos. L/D ratio more than 40 to avoid to Capillary Entarance Correction.
Material of Capillary	: Hardened steel.
Material of Piston	: Hardened steel.
Temp. Range	: 40°C to 350°C.
Temperature controlled by	: Digital Proportional Controller.
Load Range	: 0 - 200 Kg.
Load Sensor	: Strain Gauge type 4½ digit
Speed of Piston	: 10 - 200 mm/min.
Control of speed	: By thumb wheel in step of 1 mm/min.
Mains	: 220/240 Volts, AC. 50 Hz.

Carbon Black In Ethylene Plastic Apparatus

Meets IS, ASTM, BS, ISO.
a)Electric tube furnace temperature range: 600 Degree C The furnace is 250mm long approx 30mm inside diameter
b)Heating tube made of Quartz, 0-3 Ltr.
c)Two neoprane stoppers.
d)Glass Tube with Rubber pipe for connection.
e)Combustion boat,Made of porcelain.
f)Rotameter type flowmeter.2 litre capacity.
g)Three glass traps with removable ground-glass connected heads.
h)Drying tube,U-shapped made of glass Operation on 220/230 volts,Single phase,A.C,50 Cycles,Mains

Computersied UTM

Capacity:	2/20/100/200/500/1000/2000/5000 Kgf
Resolution:	0.1 gmf for 2 kgf. 1 gmf for 20 kgf. 0.01 kgf for 100/200 kgf. 0.1 kgf for 500/1000/2000 kgf. 1 kgf for 5000 kgf.
Accuracy:	+-0.5% of applied load.
Cross head speed:	1-25/5-100/25-500 mm/min Continuously variable within specified range.
Accuracy of speed	:+-1% or better.
Strain measurement:	Cross-head measurement range 0-1000 mm * 1mm (Optional: 1mm built-in clip.In Extensiometer range 0-1000mm * 0.002mm)
Accuracy:	+-1%
Displays:	In computer's Monitor.
Width between guides:	450 mm
Cross-head traverse:	1000mm Control: Through computer.
Recording/Printing :	In Ink-jet printer. (Optional:-Laser printer)
Grips :	Tension,Compression,Flexural.
Power requirement:	220/240 Volts,AC,50 Hz,1 Phase,Mains

Digital Compression Tester

Technical Specification:
Load capacity	: 1000 Kg x 0.1 Kg
Cross head speed	: 1.3 mm/min.
Load sensor	: 3.5 digit digital display
Deflection	: Scale & Digital reading 99.01 mm
Mains	: 220/240 Volts, AC, 50 Hz
Accessory	: Variable speed Drive 1-10 mm/min for above.
OTHER CAPACITY:
S-131/A. 2000 Kg x 0.1 Kg
S-131/B. 5000 Kg x 1 Kg
S-131/C. 10000 Kg x 1 Kg

Digital Metal Flow Index Tester

Meets IS , BS, Meets IS, ASTM, BS, ISO.

The apparatus is a dead weight piston plastometer consisting of a thermostatically controlled heated stainless steel cylinder with a jet and a weighted piston operating within a cylinder. The cylinder having 30mm O.D and 123mm long with a smooth,straight hole of 9.5-10mm diameter.

The jets are made of hardened steel and 8.00+-.025mm long and internal diameter are within 2.09-2.1 and 1.16-1.20mm.Heater with digital temperature indicator cum controller can maintain the temperature 300degree+-1degreeC.

A digital timer is also provided with a alarm system which will be actuated after 580secs till 600secs. Supplied complete with a 0.325,1.2,2.16,3.8,5,21.6 kg weights cleaning tool and a special type f knife. For operation on 220/230 Volts,Single Phase,50 Cycles,A.C,Mains.

Optional accessories:- 1101/01 Auto Cut off Device with variable Timer 1101/02 On line Diameter of Extruded material by micreprocessor control measuring system. 1101/03 Pneumatic Loading System 1101/04 Digital Load Indication System

Digital Specific Gravity Balance Apparatus

This Balance is specifically designed and manufactured on both better accuracy and labor saving in measurement of specific gravity.
Simply suspend the sample in air & water in succession the balance automatically sensed the weights and indicates digitally, the specific gravity directly.
TECHNCICAL SPECIFICATION :-

Measuring range	: 0.200 to 9.999
Measuring mass	: 60 gm maximum.
Electrical Mains	: 220 Volt/110 Volt, A.C, 1 Ph

Digital UTM Type 2

MODEL	DTV-1	DTV-2	DTV-3	DTV-4	DTV-5
CAPACITY *Kgf	2	20	100/200	500/1000/200	5000
RESOLUTION	0.1 gmf	1 gmf	0.01kgf	0.1kgf	1 kgf
INDICATION	DIGITAL
EXTENSION mm	1000				600
RESOLUTION mm	0.1
INDICATION	DIGITAL
SPEED mm/min	300,500	100,500	100,300,500	100,300,500	5,10,50
GRIPS	TENSION,COMPRESSION,FLEXURAL
MAINS	220/240 VA.C 50 Hz 1 P or 440/460 V A.C. 50 Hz 3P
SPECIAL FEATURE	AUTO STOP AT BREAK PEAK LOAD, MAXIMUM EXTENSION AT BREAK
SAFETY	AUTO STOP AT MAXIMUM CAPACITY AUTO STOP AT BOTH OF EXTENSION
*CAPACITY IN NEWTON IS ALSO AVILABLE

Escr Test Apparatus

The apparatus consists of :
a) Blanking die : 1 No.
b) Nicking Jig : 1 No.
c) Specimen holder : 6 Nos.
d) Test Tubes : 6 Nos.
e) Cork : 6 Nos.
f) Aluminim Foll : 1 Sheet.
g) Test Tube rack : 1 No.
h) Bending clamp :1 No.
i) Transfer Tool : 1 No.
j) constant Temp. Bath : 1 No.
Operation on 220/230 Volts, single Phase, AC.

Gloss Meter

Meets IS, ASTM, ISO, BS.
Digital Indication	: 99.9
Accuracy	: better than 1%
Head	: 20 degree/45 degree/57.5 degree/60 degree/85 degree
Power	: 1P,220 V A/C ,50 Hz

Haze Meter

Complete with electronic voltage stabilizer and Operating on 220/230 volts.
Single phase ,50 cycles ,A.C Mains.

Heat Sealer

Sealer surface: 225 * 20 mm(approx), Teflon coated
Temperature Range: Ambient to 250° C
Temperature Control: By digital Indicator cum controller
Control accuracy: ±1° C
Pressure range: 0-7 kg/cm2 (Higher range on request)
Adjustable sealing time: 0-99 sec x0.1 sec
Mains: 220/240 volt,A.C 50 Hz
Without Air Compressor

Hydros Pressure Testing M/C For Pipe

Technical Specification:
Pressure Range	: 0-70 Kg/ Cm
Tmer	: 0-999.9 x 0.1 Hr.
Maximum Pipe dia	: 315 mm
Mains	: 220/240 Volt, AC, 50 Hz, 1 ph. (for control Panel).
	: 440 Volt, AC, 50Hz. 3 Ph. (for Bath).
	(OPTIONAL 110 vOLT, ac, 60 hZ, 1 pH)
End Caps	: From 16 mm to 315 mm.

Izod Impact Tester

Meets IS, ASTM, ISO, DIN.
Pendulum impact energy(Max)	: 15 joules
Angle of fall of pendulum	: 120 degree (approx)
Effective weight of pendulum	: 2.459kg
Minimun graduation	: 0.1 joules
Striking velocity of pendulum	: 3.46m/s
Distance of axis of pendulum rotation to the point of test pieces hit by the hammer	: 400 mm.
Max permissible lose by friction and windage etc.	: 0.5 % of max.
Impact energy Combined Izod - CHARPY tester,on request.
Other capacity- 3/6 Joules

Sigma Mixture

The Mixer is similar to HBI Inc. Model No. 400 but instead of three parts it will be two parts as per BRAVENDER Mill. Capacity 100 CC. Max. temp. attainable 250°C.

Thermal Stability Apparatus

The test apparatus consists of a vertical shaft with high speed stirrer capable of maintaining a speed of 14,000+-200 r.p.m. Test stirrer shaft will be approx 0.25 in diameter at its lower end at the point of attachment of the agitator disc. The agitator will consists of a polished stainless steel disc 0.820 +-0.001" diameter and 0.062 +- 0.002 in. in thickness. The test bottles will be a flat bottel cylindrical glass container 2.28 +-0.04 " inside diameter by approx. 5 in. in height. Working on 220V, Single Phase,A/C,50 Hz mains.

Twine Screw Extruder

Twin Screw Extruder screws for continuously mixing and plastifying powder or granular thermoplastics and elastomer.
The extruder is compact one. The barrel bore is hardcrome with grinding finish and the screws are nitride. The barrel is heated electrically via 3 heating zones. The die plate is integrated in the front plate also heated.
The screws are counter rotated (towards each other. The screws are rotating at a fixed speed by Gears-Gearbox -Motor assembly at approx. 30/60 rpm.

Vicat Softening Point Apparatus

TECHNICAL DATA:
size of specimen	: 10 mm x 10 mm.
Indenting tip	: Cross sectional areas 1 mm and 3 mm long
Load on the tip	: 5 Kg. / 1 Kg
Dial Micrometer	: 0-10 mm x 0.01 mm
Heating rate	: 50° C/h or 12° C/h.
Therometer	: 0-250° C x 1° C.
Power supply	: 220/240 Volt, AC, 50 Hz. or 110 Volt AC, 50 Hz. Mains