Soft Gem Exports Private Limited

Electrically heated.

Inner chamber Size	: 18" 18" x 18"
Temp. range	: Ambient to 250°C/300°C/350°C.
Temperature controlled by Digital Controller.
Mains 220/240 Volt, AC, 50 Hz, 1 Ph.
Optional	: Digital Timer 1/7 days.

3) Goodrech Flexometer : Meets ASTM, BS.
A specific dimension sample is under repeatedly compressed under

specific load at 30 Hz frequency by electric motor cum crankshaft

assembly at a specified amplitude.

The sample assembly is placedinto a oven whose temperature

into a oven whose temperature is controlled by digital temperature

Controller. A temperature sensor sensed the increased temperature

of the sample. Also a digital timer is also aprovided.
Working on 220/240 Volt, AC, 50 Hz, 1 Ph. Mains.

Meets IS, ASTM.

Sample size	: 50 mm x 50 mm x 25mm
Thickness of spacers	: 12.5mm
Size of Testpieces:
large type	:29.0 ±0.5 mm diameter.
	12.5 ±0.5 mm thickness.
small type	:13.0 ±0.5 mm diameter.
	6.3 ±0.3 mm thickness.
Thickness of Spacers:
large type	: 9.40 ±0.01 mm(3 pairs)
small type	: 4.70 ± 0.01 mm(1 pair)
Size of each plate	: 130 mm * 48 mm * 11 mm.
Accessories	: 106/01 Hot air oven

Meets ASTM

The machine consists essentially of a metal drum(6 in. in diameter) covered with garnet paper in place by heavy elastic band. The drum is driven by 40 r.p.m by a gear with 1/4 H.P. motor. Three independent levers carry on their under surfaces the test specimens measuring 1 in. square and 1/4 in. thick. The wear on the specimens is measured directly by dial gauge readable 0.01 mm.The weight of the lever arms is adjusted that a pressure of exactly 2270 gm . (51 b) is exerted directly on the specimens.
Operation on 220/230V 1 Phase, 50 cycles,A.C Mains.
Accessories: 111/01 Four Cavity Mould

Meets IS, ASTM, BS, ISO, DIN.

Type	: Horizontal, Table Top.
Load Range	: 0-200/2000 Kg
Load Indication	: 4.5 digit display.
Strain Range	: 0-400 x 0.1mm (based on cross-head movement)
Strain Indication	: 4 digit display.
Cross Head-speed	: 1: 10 ratio (5-50/25-250/50-500 mm/min)
Mains	: 220 Volts, AC, 50 Hz, 1Ph.

Meets IS, DIN, ISO.

Size of the specimen	: 16mm dia * 6mm thick
Diameter of the cylinder	: 150mm
Length of the cylinder	: 470mm
Speed of the cylinder	: 40 R.P.M
Force on specimen	: 10 N
Lateral movement of specimen in one revolution of the cylinder	: 4.2mm
Total abrasion distance	: 40 meters(about 84 revolutions)
Motor	: 1/4 H.P Single Phase,220/230 Volts,50 Cycles,Mains.
Accessories :
112/01 cutting die for test specimen(Rotary type)
112/02 Moulding die for test specimen(four cavities)
112/03 Abrasive cloth

Meets IS, ASTM.

Size of the sample	: 20 * 20 mm
Number of test samoles tested at a time, Two
Distance of each test piece from center of rotation	: 63.5mm
Total load on test pieces	: 3.62 kg.
Speed of rotation of abrasive disc	: 35±5 R.P.M
Motor	: 1/4 H.P
Single phase,A.C., 50 Cycles,Mains
Accessories	: 110/01 Cutting die for test specimen
	110/02 Moulding die for test Specimen

Meets IS, ASTM.

Indentor	: 305 mm dia with bottom edges having 13mm radius. for IS 1741(105 x 105 x 3mm for IS:8391 & 11061);
Stroke	: Adjustable between 0 to 60mm.
Stroke rate	: 4 Cycles/sec Pre-set
Counter	: 6 digit digital
Motor	: 1/4 H.P single phase 220V A.C. 1P.

Goodrich Flexometer. ASTM D-623-BS:903

Meets IS, ASTM, BS.
The tester consists of high-speed stirrer with specific dimensionof shaft at a speed rpm 14000 + 200.
A digital counter shows the speed in r.p.s and a digital timer is Also provided. Working on 220/240 Volt, AC, 50 Hz, 1 Ph Mains.

The apparatus consist of a heat resistant beaker in which liquid is heated by a hotplate heater and temperature is controlled by an electronic variac and temp is displayed by digitally. Temp. range ambient to 300°C + 1°C. Stirring done by magnetic stirrer. To see the melting of the specimens lighting and high power lens are provided.

Working on 220/240 Volt, 50 Hz, 1 Ph.

Electrically heated.

Temperature Range	: upto 1000°C/1200°C.
Temperature Control by Digital Controller.
Inner chamber Size	: 100 x 100 x 225 mm.

Mains 220/240 Volt, AC, 50 Hz, 1 Ph.

Meets IS, ASTM, BS, ISO.

Size of block	: 400 mm dia*300 mm long.
No. of cells	: 7 nos./3 nos
Size of cells	: Can be controlled between 5 degree C above ambient to 250 degree C with the help of Digital Temp. Indicator cum Controller.
Accuracy	: Upto 100 degree C ± 1 degree C
	Upto 250 degree C ± 2 degree C

Air Flow Control By Rotameter type Flowmeter.

Meets ASTM.

Load cell	: Capacity:200 gm.
Resolution	:0.01 gm

Working on 220/240 Volt,AC. 50 Hz,1 Ph,Mains

Meets IS, ASTM. Indentor: 305 mm dia with bottom edges having 13mm radius. for IS
1741(105 x 105 x 3mm for IS:8391 & 11061);
Stroke: Adjustable between 0 to 60mm.
Stroke rate: 4 Cycles/sec Pre-set
Counter: 6 digit digital
Motor: 1/4 H.P single phase 220V A.C. 1P.

This consists of a rigid A1. Plate standing vertically on a heavy cast base.The specific gravity scale is printed on the vertical plate and a pointer is pivoted in fine bearings to register sp. gr. value.

From	: 0.9 to 2.0 graduated 0.01.
	2.0 to 2.5 graduated 0.02.
	2.5 to 3.0 graduated 0.05.

The scale is calibrated from 0.9 to 3.0.

Meets ASTM. : Capacity Resolution Indication

Split type oven	: Working length :250mm
Inside bore	:13mm
Temperature range	:5 degree above ambient to 250 degree C
Control	: PID controller Temp.
Accuracy	: ±0.5 degree C at 177 degree C
Load Cell
:0-20 N.
:0.01 N.
:0.01mm
Timer	: Range 0-9999 Secs.
Mains	: 220/240 volts,AC,50 Hz,1 Ph

Meets IS, BS, ASTM.

Maximum size of specimen	: 200 x 200 x 100mm
Dial gauge range	: 0-10mm x 0.01mm
Size of pressure foot	: 28.7 mm dia(6.5 cm x cm)
Force on pressure foot	: 3 gm
Spacers	: A set of four spacers of thickness 50 mm,20mm x 2 and 10mm.
Range	: 0 - 25 x 0.01mm.
	0 - 10 x 0.01 mm.
	0 - 5 x 0.002 mm.