• It melts when heated and adheres to the surface onto which it is applied
• It holds the components prior to fixation and gives a clean burnout.

• In gold-plated or plain versions.
• Even if breaks or splits occur in the acrylic the denture stays in position.
• Improves considerably strength of acrylic denture.

Dental Shellac Base Plates/Sheet Wax

Dental Shellac Base Plates

• Thickness: Upper/Lower Base Plate: 1.1- 1.3mm. (Custom Thickness Catered)

• Colour: Dark Brown/ Light Brown / Silver (aluminum based & mica free) / pink.

Properties & Advantages

• They are ready to use Maxillary & Mandibular plates - 8 Maxillary and 4 Mandibular.

• Optimum Heat resistance to minimize overheating of the Plate.

• Easily adaptable on heating and easy to work with.

• Retain the shape stability and do not warp back on cooling. 

• Optimum Mechanical strength to resist breaking during Try - in Denture, 

• Not Adhesive to Plaster.

Packing

Each Packet of 'MAARC' Base Plate contains - 8 upper & 4 Lower Plates (Custom Packing Available)

Type:

It comes in various colours as pink, yellow, brown, Aluminium, high Melting Point, Low Melting Point.

MODELLING WAX / SHEET WAX / BASE PLATE WAX

Thickness:

• 1.1 - 1.3mm.(custom thickness catered).

Size:

• 160mm x 90mm

Properties & Advantages:

• The wax is formable at slight increased temperature.
• Sufficient hard and resistant on cooling to prevent occlusion changes during Try - in with patient before making Final Denture to prevent Failure of Final Denture.
• Easy & Clean carve on teeth.
• Bends without Cracking

Packing:

Each Packet of 'MAARC' Modeling wax contains 12 sheets of wax weighing approx. 225 - 250 gms wrapped in non adhesive Silicone Paper to Facilitate easy removal.

Also available in 1/2 & 1kg pack.(Custom packing available).

Shades: It comes in various shades like Light Pink, Dark Pink, Red, Ivory, Normal Pink, etc.

Type: It is manufactured in various hardness like soft, regular, medium hard, extra hard specially keeping in mind the various climatic temperature of different countries.

Technical Specifications:

Congealing Point

• Hard Modellling Wax : 52°C
• Soft Modelling Wax : 54°C

Needle Penetration:

• Hard Modellling Wax: 15.76 Using standard needle & 100gm weight at room temp acceptable range 15-16
• Soft Modelling Wax: 17.5 Using standard needle & 100gm weight at room temp acceptable range 17.5-19

• Stiff enough to hold the wax patterns and does not deform in shape.
• Easy burn out without residue

• Comes in Plastic container each containing 500gms of sprues and 200gms of spools

• The blue inlay wax also comes in stick form, there are 20 stick per box of blue inlay. It is used in colleges by students for easy its application

PATTERN WAX / INLAY ONLAY PATTERN WAX

The basic classification from our side is being done based on hardness and stiffness & flow of waxes

Softer waxes with high flow are more flexible and are used as base; harder waxes are less flexible and stiff and are used as build up.

• Cervical Wax (Orange): Soft type with degree of fluidity that will allow it to flow and fit perfectly in cervical areas, high adaptation and stability to surfaces. It will wet model surface without shrinkage.

• Cervical Wax (Blue): Harder than Orange wax.

• Cervical Wax (Blue / Red / Ivory): Standard inlay wax wherein the Pattern comes out easily from the Plaster Surface.

• Undercut wax (Green): Harder than Red wax used where hard Pattern waxes are preferred.

• Undercut Wax (Violet): Harder than Green Wax - Used for Coping of Patterns to add mechanical strength and as undercut wax.

• Sculpturing  Wax (Coffee): Used for Undercuts and adding Mechanical Stability to Wax Patterns of jacket Crowns.

• Carving  wax (Magenta): Hard Inlay wax. With medium flow for built up

• Presentation Ivory Inlay wax: A white, enamel-like wax used to makes a more aesthetic case presentation (wax-up). Easy carving properties. Also aids in the fabrication of temporaries.

Properties & Advantages

• The wax does not withdraw on Solidifying, i.e. it does not lift off the edges while solidifying

• Has Got Good Flowing and Carving Properties.

• The softer waxes are flexible enough to form base of wax patterns

• The harder waxes add strength to the wax patterns and are used for build up.

• The harder waxes are stiff enough for using as undercut waxes and margin waxes where less thickness of wax and high strength for the given thickness is required.(Low Shrinkage of the wax)

Packing :

• The Wax comes in Plastic box Packing of 100/200 gms Packing.

A] ORTHOCAL STONE PLASTER

TYPE : V

COLOUR: OFF WHITE.

SPECIFICATIONS:

• For crown and bridge, dies and cast partials.

• For basing dentate arches and opposing models.

• For making study models.

• In use where economical yet tough, non brittle and durable models are required.

WORKING SPECIFICATIONS:

PACKING: Available in 1 / 3 / 5 kg heavy gauge plastic bag and 25 / 40 kg polyester lined gunny bags.

B] DENTAL STONE

TYPE: III

COLOUR: YELLOW / GREEN / OFF WHITE

SPECIFICATIONS:

• For fabricating custom Trays, mouth guards and vacuum formed splints.

• For denture repairs

• Studycasts

• Lab procedures such as Articulator cast mounting

• For processingfull or partial acrylic dentures and counter models

WORKING SPECIFICATIONS:

PACKING:

Available in 1 / 3 / 5 kg heavy gauge plastic bag and 25 / 40 kg polyester lined gunny bags.

Send Bulk Enquiry

NI-CR ALLOY FOR CAST RESTORATIONS (NON-PRECIOUS ALLOY):

• It is in the form of rectangular pellets each weighing appx 6gms

Nominal Composition:

Ni – 52%; Cr – 14%; Mn – 17%; Cu – 10%; Fe – 4%; rest – 3%

Properties & Advantages

• It is beryllium free alloy with excellent castability

• It is reusable with addition of appx 50% fresh metal during recasting.

• It can be cast in open flame.

• It has got good burnish ability and is easy to finish.

• It can be used for making cast crown bridge and pontics and frames for hard resin crowns.

• It can be cast at the moment ingots have melted attributed to excellent fluidity .

• Removal of oxide layers formed during castings is not necessary for the metal oxides that are formed are lighter in density and remain behind during centrifugal casting .

Packing : It comes in 500gms and 1Kg plastic case packing.

CERA-LOCK ALLOY (BERYLLIUM FREE) FOR PFM BONDING – CERAMIC ALLOY:

• It comes in the form of cylindrical pcs each weighing appx 7gms.

Nominal Composition

Ni – 66-70%; Cr – 19-23%; Mo – 5-7%; rest 4%

Properties & Advantages

• Beryllium free formulation.

• Optimum castability and bonding strength in PFM restorations.

• It produces a uniform oxide film at porcelain metal interface ensuring strong chemical bonding.

• A Cr Mo percentage amounting to greater than 20% assures corrosion resistance.

• High mechanical strength & stability on account of refined grain structure.

• Good burnishability

• Brighter shine and finish.

• Suitable for open flame casting

Packing

• It comes in 500gms and 1Kg plastic case packing.

HI-LOCK ALLOY (BERYLLIUM FREE) FOR PFM BONDING – CERAMIC ALLOY:

• It comes in the form of cylindrical pcs each weighing appx 7gms.

Nominal Composition

Ni 68-72 %, Cr 14.5-17%, Mo 7-10%, Si 2-3.5%, Al, Fe & rest elements 4%

Properties & Advantages

• Beryllium free formulation.

• Optimum castability and bonding strength in PFM restorations.

• It produces a uniform oxide film at porcelain metal interface ensuring strong chemical bonding.

• A Cr Mo percentage amounting to greater than 20% assures corrosion resistance.

• High mechanical strength & stability on account of refined grain structure.

• Good burnishability

• Brighter shine and finish.

• Suitable for open flame casting

Packing

• It comes in 500gms and 1Kg plastic case packing.

JEWELLERY WAXES:

Carving wax blocks available in various sizes can easily carved by hand & can be used on CNC machines for jewellery Designing.

A) for Extrusion

B) For Pour Filling

Both the wax is very stable at temperature from 12ºC to 40Cº.
Pour Filling waxes are suitable for automatic machines for tray filling

Special properties of Jewellery waxes for designing purpose:

High Melting point of 120 degree C, machine friendly, does not stick to the tool, very clean carving – the flakes during carving does not stick to the model (very important), The waxes are soft but tough in nature and it can be hand carved also

FOUNDRY WAXES:

For Investment Casting Foundries
Wax With very low shrinkage low ash content and higher dimensional stability.