Siddhivinayak Dyechem Private Limited, Thane

Waxof is a Carboxylic amide derivative cationic fabric softener, designed to give a soft, fluffy & velvet like feel. It has minimal yellowing tendency. It is suitable for Natural, Synthetic fibers & blends. It is very stable to hard water.

 Typical Characteristics:

• Solids - 20 22 %
• Nature - Cationic
• Appearance - Creamish paste
• Odour - Mild Fatty Quaternary
• Stability - Stable to hard water up to 1200 ppm
• Compatibility - Compatible with cationic & non-ionics. Not compatible with anionic

Advantages:

• Easily dispersible in cold water
• Very good re-wet properties
• Gives an outstanding softness with a balanced internal softness & surface feel
• Excellent anti-static performance on Viscose, Nylon, Wool, Acrylic & Polyester Fabrics
• Minimal scorch yellowing exhibits very little tendency to yellow in high temperature dryers

Application:

Waxof can be applied by exhaustion & padding methods Exhaustion method Depending on desired results, treat with 2 5 % o.w.f. of Waxof, adjusting the pH to 5 5.5 with acetic acid, for about 20 30 minutes. Further hydro extract & dry Padding method Pad with 20 60 gms / lit of Waxof depending on desired results.

Packaging : 50 kg HDPE Drums

Product Code:

WAXOF

SUPERSOFT 1111 is a fatty acid condensate concentrated cationic softener for use in textiles as a finishing agent. SUPERSOFT 1111 is easily soluble in cold water imparting excellent surface softness on dyed as well as prints. SUPERSOFT 1111 also improves the sew-ability of knits and wovens.

Properties :

• Ionic Nature
• Cationic Physical Aspect
• Creamish flakes Solubility
• Cold water Nature
• Low Yellowing

Procedure For Dilution:

Take 10 – 20 kgs of flakes and slowly add in 50 – 80 litres of water with continuous stirring. Stir it for about 1 hr and then keep the paste overnight. Next day, start using as per requirement. Alternately, add 10 kgs of SUPERSOFT 1111 flakes to 90 litres of water & leave overnight. Hand stir & start using the product next day onwards.

Application Data On The Diluted Product: Special Advantages

• Imparts excellent Surface smoothness along with internal softness to cellulose's.
• Substantive to textile fibres, therefore economically applicable from long liquors.
• Imparts ideal frictional properties to fibres for many conversion processes.

Application Methods:

Being cationic SUPERSOFT 1111 will have affinity for fibres and can therefore be applied by exhaust methods. A pH of 6.0 to 7.0 is recommended for maximum exhaustion. It is also applicable by pad or immersion/ squeeze technique, the bath being continuously recharged during the process.

Packing : 25 kg HDPE Bags

Product Code:

Supersoft-1111

NANOSIL is a highly emulsified, amino reactive micro-silicone emulsion intended for use as a high grade, silicone softener product for the textile / garment wet processors. NANOSIL is easily dilutable in cold to warm water, at temperatures of between 150C to 500C, under light stirring. It is a advisable to pre-dilute this product with suitable clean, slightly acidic cold to warm water (pH 4.5-6) before actual application. NANOSIL is compatible with most non-ionic and cationic textile auxiliaries, softeners and chemicals. Prior tests are required to ascertain its compatibility.

Physical Properties :

• Silicone Type: Reactive
• Appearance : Clear Solid
• content : 30
• Ionic type : Weak
• solubility : Cold

Typical Applications:

On textiles and garments wet processing to achieve:

• Durable silicone surface feel
• Durable softness to fabrics / garments treated
• Improved fabrics / garments tear strength
• Improved fabrics / garments wrinkle resistance
• Improved fabrics / garments elasticity
• Visibly reduced yellowing compared to other cationic softener, silicones
• Improved silicone yield due to its reactivity with fibers under long liquor ratios

Exhaust method:

Maintain M L R to 1:6 & temperature to around 45 deg. C. Depending on desired results, treat with 0.2 – 1 % o.w.f. of Nanosil, adjusting the pH to 5 – 5.5 with acetic acid, for about 20 – 30 minutes. Further hydro extract & dry.

Padding method: Pad with 1 – 5 gms / lit of Nanosil, depending on desired results.

Typical Diluting Conditions:

• Temperature of Diluting Water : 150C to 500C.
• pH of Diluting Water : 4.5~6
• Avoid high temperature, alkaline pH. Slow speed stirring suffice.
• Avoid water contaminated with iron and copper ions.
• To add NANOSIL into stirring water, stir for few minutes, check pH of mixture
• Adjust pH to slightly acidic condition(4.5 ~ 6.0), if necessary.

Packing : 50kg HDPE drum

Storage : To store cool under shade to prolong shelf life of product. Never exposed product to direct sunlight. Keep lid tight when not in use to prevent possible contamination to the product. Stir well before use.

Transport: Product is non-flammable by itself and is not classified as hazardous for transport.

Shelf life: Minimum 6 months when stored at 250C or below, in unopened conditions.

Product Code:

Nanosil

C S -100 is a fatty acid condensate concentrated cationic softener for use in textiles as a finishing agent. C S -100 is easily soluble in cold water imparting excellent surface softness on dyed as well as prints. C S - 100 also improves the sew-ability of knits and woven.

Properties:
 

• Ionic Nature
• Cationic Physical Aspect
• Creamish flakes Solubility
• Cold water Nature
• Low Yellowing

Procedure For Dilution:

Take 10 – 20 kgs of flakes and slowly add in 50 - 80 liters of water with continuous stirring. Stir it for about 1 hr. and then keep the paste overnight. Next day, start using as per requirement.

Application Data On The Diluted Product : Special Advantages

• Good softener and antistatic agent for all fibers.
• Substantive to textile fibers, therefore economically applicable from long liquors.
• Imparts ideal frictional properties to fibers for many conversion processes.

Application Methods:

Being cationic C S 100 will have affinity for fibers and can therefore be applied by exhaust methods. A pH of 6.0 to 7.0 is recommended for maximum exhaustion. It is also applicable by pad or immersion/ squeeze technique, the bath being continuously recharged during the process.

Product Code:

CS-100

Zensof NY is a non ionic fatty acid condensate product, for imparting a full & soft handle without yellowing, for white goods. It has no effect on the shade or light fastness of dyed goods. Zensof NY is compatible with fluorescent whitening agents. Zensof NY can be applied to woven, knits, terry cloth & non woven fabrics.

Typical Characteristics:
 

• Nature : Non ionic
• Appearance : straw colored
• pH (1% Sol.) : 6 7
• Solubility : Miscible in cold water
• Compatibility : Compatible with cationic, anionic & non Ionics.

Application

Zensof NY can be applied by exhaustion & padding methods. Maintain M L R to 1:6 & temperature of 40 50 C. Depending desired results, treat with 0.4 0.8 % o.w.f. of Zensof NY, adjusting the pH to 5 6 with acetic acid, for about 20 30 minutes. Further hydro extract & dry Pad with 5 -15 gm/lit (for cellulose) & 3 - 10 gm/lit (for synthetics) of Zensof NY, depending on desired results.

Packing: 50 kg HDPE Drums

Storage : Store in cool dry place. Avoid direct sunlight and heat.

Transport : Product is non flammable and not marine pollutant.

Product Code:

Zensof-NY