We offer multistage high pressure pumps, with the following features:

Features:

I. Casing: Horizontal radially split multistage ring section pump manufactured as a compact design unit. The stages are sealed by O - rings and clamped together by tie rods.

II. Impeller: Closed type radial impellers are hydraulically and statically balanced by back vanes / balancing holes.

III. Shaft: High tensile shaft supported by anti-friction bearings and protected by shaft sleeve.

IV. Bearing:Grease lubricated deep groove ball bearings or roller bearing are provided.

V. Stuffing Box: As a standard, stuffing box is provided with sealing connection on suction side but for higher pumping temperatures, it can be provided with cooling cover for external cooling.

VI. Drive: Suitable for coupling with an electric motor or an IC engine. These can be connected directly with a flexible coupling or with a belt drive.

Range

• Capacity up to 10,000 m3/hr
• Head up to 180 m

Applications

• Boiler Feed Application
• Mine De-watering
• General Water Supply
• Water Supply to high rise buildings
• Sprinkler installations
• Fire fighting
• Condensate Transfer
• Descaling Operations

We offer Mixed Flow Pumps that are single-stage centrifugal pumps suitable for handling pure or contaminated liquids in large quantities. These pumps are of robust construction and have long working life. These pumps are also low in energy consumption due to very good efficiency.

The precision machined pump shaft is seated in amply oil / grease lubricated bearings and protected by a shaft sleeve in the stuffing box area. The integrally cast feet of the casing transmit any forces originating from the pipework directly to the foundation, this means that the rotor is not subject to any bending and thus optimal working life of the bearings is assured. Direction for the rotation of the pump is clockwise, when viewed from the driven end.

Electric motors can be used as the prime mover, with diesel engine as the prime mover, the pump's direction of the rotation is anticlockwise from the driven end.

These pumps can be supplied in standard cast iron or in any other non-standard or special material combinations.

Applications:

• Sugar, pulp and paper
• General water supply
• Power
• Breweries & distilleries
• Sewage disposal
• Irrigation
• Cooling water

We offer Horizontal Split Casing Centrifugal Pumps that comes with the following features:

I. Casing: Axially split volute cases with suction and discharge branches located opposite in line in the lower half. This allows easy removal of the rotating element, without disturbing the pipe work. Pump required for higher heads have double volute casing to minimize radial thrust.

II. Impeller: Single entry and double entry, closed type impellers are hydraulically and statically balanced.

III. Shaft: Machined from high quality steel. The shaft is sturdily proportioned to minimize deflection and provide long reliable service.

IV.Sleeves: Sleeves are provided to protect the shaft and ensure longer shaft life.

V.Neck Ring: Designed with appropriate clearances and materials to minimize leakages while ensuring along impeller life.

VI> Bearing: Deep groove ball bearings are provided at the drive and free ends and are designed for high reliability and long life.

Range

• Capacity up to 10,000 m3/hr
• Head up to 180 m

Application

• Industrial and Municipal Water Supply
• Cooling Towers
• Injection Water
• Spray Pond
• Air-conditioning
• Water
• Treatment Plant
• Fire Fighting
• Irrigation

Range

• Capacity up to 10,000 m3/hr
• Head up to 180 m

Application

• Industrial and Municipal Water Supply
• Cooling Towers
• Injection Water
• Spray Pond
• Air-conditioning
• Water
• Treatment Plant
• Fire Fighting
• Irrigation

Torque flow pumps are manufactured in nickel chrome steel having 500-550 BHN hardness to withstand the abrasive action of liquid being handled. It can handle solids upto full diameter size of discharge connection without danger of clogging. The principle of the hydro-dynamic liquid coupling is used for the energy transfer to the pumped liquid. The impeller generates a whirlpool in the casing and the whirlpool now acts as a pumping elements (implore in the casing. It is a totally non-clog concept in pumping.

Range

• Capacity : upto 1,500 m3/hr
• Head upto 100

Application

• Abrasive Slurries
• Sewage
• Industrial Waste
• Sugar
• Pulp and Paper
• Steel
• Power
• Fibre
• Textile
• Waste Water
• Grain Wash
• Solid Handling
• Cement Aquaculture

Torque flow pumps are manufactured in nickel chrome steel having 500-550 BHN hardness to withstand the abrasive action of liquid being handled. It can handle solids upto full diameter size of discharge connection without danger of clogging. The principle of the hydro-dynamic liquid coupling is used for the energy transfer to the pumped liquid. The impeller generates a whirlpool in the casing and the whirlpool now acts as a pumping elements (implore in the casing. It is a totally non-clog concept in pumping.

Range

• Capacity : upto 1,500 m3/hr
• Head upto 100 m

Application

• Abrasive Slurries
• Sewage
• Industrial Waste
• Sugar
• Pulp and Paper
• Steel
• Power
• Fibre
• Textile
• Waste Water
• Grain Wash
• Solid Handling
• Cement Aquaculture

Made of nickel chrome steel having of 500 to 550 BHN for the following parts viz. Pump casing, impeller and gland plate. This gives the pumps a very long life owing to the high rate of abrasion resistance. The pumps are compatible for pumping all abrasive liquids.

Standard Features

• Long life due to replaceable wearing parts
• Dynamically balanced rotating parts
• Easy maintenance
• Easy availability of spares
• Designed for automatic air release during primping
• Grease lubricated deep groove all bearing

Special Features

• Quick automatic self priming action
• Repairs possible without disturbing the pipe connection
• Non-clogging impeller to handle suspended solids
• Portable when fitted on trolley
• Suitable with motor
• No need for foot valve

Range

• Capacity : upto 250 m3/hr
• Head upto 50 m

Application

• Sump Drainage
* De watering
* Ash Slurry
• Wet Scrubber

We manufacture and supply Water Pumps as per the following features:

Range

• Capacity : upto 1,000 m3/hr
• Head upto 140 m

Application

Water Supply
• Drip Irrigation
• Cooling Tower
• Condensate handling
• Air-conditioning
• Fire Fighting
• Service Water
• Chemical Process
• Effluent Treatment
• Hydrocarbon
• Viscous Liquid
• Acids Juice Pump
Distillery

Our range of Liquid Ring Vacuum Pumps are available with following specifications:

Range

• Free Air Capacity :
upto 4,975 m3/hr
• Vacuum upto 685 mm Hg

Application

• Chemicals
• Pharmaceuticals
• Food
• Sugar
• Plastic
• Paper
• Pulp
• Priming
• Air and Gas Transfer

We manufacture and supply Rota Pumps as per the following specifications:

Range

• Capacity : upto 100 m3/hr
• Head upto 50 m

Application

• Massecuite
• Magma

Our range of Non Clog Pumps are used for varied industrial requirements. The specifications are:

Range

• Capacity : upto 2,000 m3/hr
• Head upto 60 m

Application

• Sewage
• Effluent Treatment
• Unscrewed Juice
• Slurry
• Drainage
• River water
• Sludge
• Grain Wash
• Syrup
• Melt
• Mud

We manufacture and supply Vertical Turbine as per the following specifications:

Range

• Capacity : upto 20,000 m3/hr
• Head upto 300 m

Application

• General Water Supply
• Cooling Tower
• Spray and Injection Water
• Irrigation
• Hydro power