We provide various hydraulic garage equipment of Vanjax. Our products in this range are offered in different capacities as per the requirements of our clients. These capacities vary in terms of technical specifications like lifting capacity, lifting range, overall dimension, shipping weight, package size, hydraulic stroke and hydraulic compression. Our products in this range include:
 

• Bottle jack
• Trolley jack
• Air Hydraulic Jack
• Floor Crane
• Motor Cycle Lifter
• Frame Straightner
• Port Hydraulic Equipment
• Workshop Press
• Spring Dismantler
• Pipe Bender
• Axle Stand
• Engine Stand
• Port Air Compressor
• Roller Seat
• Steel Creeper
• Jacking Beam
• Fork Lift Jack
• Scissor Truck
• Puller
• Bead Breaker
• Pneumatic Pump
• Low Lift Jacks
• Multipurpose Tool Kit

Apart from Vanjax, we also deal in various hydraulic equipment provided by Polyhydron. These equipment are manufactured by fine quality components conforming to international quality standards. Our Polyhydron range of hydraulic equipment consists of following products:

• Puller
• Pipe Bender
• Cable / Wire Cutter
• Flange Spreaders
• Cable / W.R Cutter Portable
• Rod Cutter
• Bolt Tensioner

All these products are provided in varied technical specifications in terms of hydraulic thrust, maximum spread, hydraulic strokes, cutting capacity etc.

We provide various hydraulic material handling equipment from renowned manufacturers

TYPE	VXHPT-2000PU	VXHPT-2500PU	VXHPT-3500PU
CAPACITY	2000 kgs	2500 kgs	3500 kgs
WIDTH OF FORKS	160 mm	160 mm	160 mm
WIDTH BETWEEN FORKS	225 mm	365 mm	230 mm
OVERALL FORK WIDTH	540 mm	685 mm	550 mm
OVERALL LENGTH	1500 mm	1610 mm	1550 mm
FORK LENGTH	1100 mm	1220 mm	1150 mmv
MIN.HEIGHT OF FORKS	90 mm	85 mm	85 mm
MAX.HEIGHT OF FORKS	200 mm	200 mm	195 mm
OVERALL HEIGHT	1235 mm	1210 mm	1248 mm
NET WEIGHT	72 kgs	76 kgs	86 kgs

We deal in a wide range of motorised hydraulic pressure test pumps fabricated with quality components. Each component is made of fine grade materials. Our range of pressure test pumps is provided upto 14000 PSI. Various components of our pressure pumps are mentioned here with their respective fabricating materials:
 

• Non-return Valve is made of S.S (410) material
• Out-let is made of M.S (IS : 226) material
• Pressure Guage is made of STD material
• Syphon is made of M.S (IS : 226) material
• Relief Valve is made of S.S (410) material
• Non-Return Valve is made of S.S (410) material
• Spundle is made of S.S (AIS1410) material
• Handle is made of M.S (IS : 226) material
• Body M.S (IS : 226) material
• Tank is made of Galvanised material
• Stand is made of M.S (IS : 226) material

Hydraulic Power In Action

Model	CAP (ton)	HYD.STROKE (mm)	CLOSED HEIGHT(mm)	TOTAL LIFT (mm)	OUTSIDE DIA(mm)
VXRC - 05/150	5	150	230	380	45
VXRC -10/150	10	150	230	380	60
VXRC -20/150	20	150	230	380	80
VXRC - 30/150	30	150	230	380	100
VXRC -50/150	50	150	275	425	130

We offer superb quality mechanical jack made by reputed manufacturers. These are provided in specifications with different stroke, models, working pressure and capacity. Our range of mechanical bottle type jacks are offered with 3 ton to 65 ton capacity. Conforming to quality norms of internationals standards, our mechanical jacks are widely used in various applications.

We provide a comprehensive range of automotive equipment from reputed manufacturer Penta. Our range of automobile special tools is offered for Maruti, Tata, Hero Honda, Bajaj, TVS, Yamaha and customised tools for other two and four wheelers. The assortment also includes following auto equipment:

• Hand Operated and Pneumatic Grease dispensers
• High Pressure Washers
• Two wheeler Ramp
• Hydraulic Trolley Jacks
• Oil Collector
• Spark Plug Cleaner
• Tyre Inflators
• Compression Tester
• Battery Chargers
• Battery Load Testers
• Automated Special Tools 

These equipment are offered in various technical specifications. A few of these are mentioned here:

Hand Operated & pneumatic Grease Dispensers 
 

Model	Hand Operated			Pneumatic
Capacity	5 Kg	10 Kg	20 Kg	25 Kg	50 Kg
Pressure	3000 Psi			8000 Psi
Output	3 gms Per Stroke			350 gms per Minute
Hose Length	2 mts hydraulically crimped at both ends
Type of Hose	Thermoplastic / Rubber with bursting press ure at      24000  psi
Pressure Plate	Provided
Pressure Guage	Not Provided			Provided
Dimension mm L * B * H	220 * 260 * 560	260 * 280 * 560	310 * 330 * 630	310 * 440 * 955	420 * 530 * 1010
Weight (Nett)	9.5 Kg	14 Kg	17 Kg	21.5 Kg	32 Kg

  
High Pressure Washers
 

Model	PE 50	PE 100	PE 200	PE 300
Operating Pressure     Motor Power     Motor RPM     Pump RPM     Power Supply     Frequency     Hose Length (Std.)     Dimension (mm)     Weight with Motor	15 Kg / cm2 8 LPM 1 HP 1440 500 230 V 50 Hz 5 Metres 700 * 370 * 460 50 Kg	18 Kg / cm2 8 LPM 1.5 HP 1440 360 230 V / 415 V 50 Hz 5 Metres 750 * 410 * 550 63Kg	25 Kg/cm2 13 LPM 2.0 HP 1440 360 230 / 415 V 50 Hz 5 Metres 750 * 410 * 550 66 Kg	40 Kg/cm2 15 LPM 3.0HP 1440 360 230 / 415 V 50 Hz

Our company deals in a wide range of cutting tools provided by Bipico. These are required in various industries. These cutting tools bear some striking features like high corrosion resistance, durable, trouble free operation and long service life. Available in optional specifications, Bipico range of various cutting tools offered by us includes:
 

• Hacksaw Blades
• Metal Cutting Bandsaw Blades
• Bi-Metal Bandsaw Blades
• Jigsaw Blades
• HSS Tool Bits

 

We provide a wide assortment of pipe and bus bar bending machines in types of hydraulic and motorised operations. Our hand operated hydraulic pipe bending machines are offered in various technical specifications in terms of size, pressure capacity and formers. Our EJECTO-MATIC hand operated pipe bending machine is provided with standard formers and accessories. It is available in sizes of 1/2" to 3", 1/2 to 4" and 2" to 6".
 
Our motorised hydraulic pipe bending machines are from Hydrobend and Ejecto-Matic. These are hydraulic motorised heavy duty bench type pipe bending machine available with hydraulic pressure capacity of 45 tons. These are ideally suitable to bend pipes upto 8".
 
Our Bus Bar bending machines offered in horizontal type is ideally suitable for bending Copper, Aluminium and mild Steel Bars. The vertical variant if offered as Deepak Bus bar bending machine.

We offer Spray guns of Pilot range. Pilot is a recognized name among spray gun manufacturers. Our spray guns are used for automobile spray painting. For easier cleaning the body is provided with a non-stick coating. These high pressure spray guns are provided with sharp stainless steel nozzle and needle. This enables the spray guns to be used with water borne and solvent based products. The gun is designed to operate at speeds to match high production rates and paint saving.