IndiaMART.com
Indiamart

  • logo
  • SMS Technologies

    Mumbai, Maharashtra

  • Year of Establishment: 2005
    IndiaMART Member Since: 2006
    Products [60]

    Mobile: +(91)-9821828844

Pump Motor Protector Controller

Pump Motor Protector Controller

Features :

  1. Digital Display of actual motor current, settings & faults
  2. Easy to install (only 3 input supply & 3 motor power supply wires to be connected )
  3. Completely Automatic Operation
  4. Complete Protection of Pump Motor
  5. Built in contactor
  6. Replaces Starter
  7. Cyclic on & off timer
  8. In case of dual pumps, alternate switching of pumps to ensure longer life
  9. Instantenous phase failure protection
  10. Dry run prevention
  11. Tank level control

Benefits :
  1. Saves electricity & water
  2. No manual operations
  3. Saving in operating cost
  4. Increase in motor life
  5. Increase in safety
Applications :
  1. High rise buildings
  2. Pump
  3. Sewerage Pumps
  4. Agriculture / Borewell
  5. Hospitals
  6. Industries
  7. Dewatering
  8. Hotels
  9. Societies

 Description :
 Our Pump Motor Protector Controllers are microcontroller based systems with instant response (faster than conventional starter systems) as this reponse is based on solid state devices & ultra precision current sensing elements. These systems trip and protect instantly at improper current sensing. Pump Motors burn due to various reasons like 1) Over Load, 2) Voltage Fluctuations, 3) Mechanical & Electrical Malfunctioning, 4) Phase failure i.e. single phasing, 5) Dry Run and Reverse Rotation etc.
This implies that Motors do not fail because of voltage but it burns because of current. So, by monitoring & controlling the current variation for its higher and lower allowable value, we can safe guard pump motor. Common features & advantages of these systems over conventional systems are mentioned in detail with each product.
These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.

Models Available :
  • Borewell Controller
  • Two Tank Pump Controller
  • Sewerage/Dewatering Pump Controller
  • Hydro-pneumatic Control Panel
  • Fire Fighting System Controller
  • High Level Alarm

Bore Well Submersible Pump Controller

Bore Well Submersible Pump Controller


Features:

  • With Cyclic Timer
  • Probe-less dry run sensing
  • Tank Overflow Protection
With common features like
  • In-built Starter
  • Completely Automatic Operation
  • Complete Protection of your Pump Motor
  • Digital Display of faults as well as parameters 
  • Highly accurate & reliable
  • Easy to maintain with efficient service back-up
Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.
These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.

 
Minimum Order Quantity: 10 Sets

Domestic Pump Motor Protector Controller

Domestic Pump Motor Protector Controller

For Monoblock/Monosub pumps for Two Tank/BMC/Domestic applications

  • Level Sensing of Sump as well as Overhead Tank
  • Over-flow & Dry Run Protection
  • Easy to maintain with efficient service back-up
  • Also available for only one tank control
Applications :
  • All buildings (Housing Societies, Schools, Hospitals etc.) for transfer of water from sump tank to overhead tank
  • Industries, for the transfer of water from one tank to another
 With Common features like,
  • In-built Starter
  • Completely Automatic Operation
  • Complete Protection of your Pump Motor
  • Digital Display of faults as well as parameters 
  • Highly accurate & reliable
  • Easy to maintain with efficient service back-up
Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.
These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.

Pump Controller For Multiple Upper Tanks

Pump Controller for Multiple Upper Tanks

With Common features like,

  • In-built Starter
  • Completely Automatic Operation
  • Complete Protection of your Pump Motor
  • Digital Display of faults as well as parameters 
  • Highly accurate & reliable
  • Easy to maintain with efficient service back-up
Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.
These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.  

Hydro-Pneumatic / Pressure Operated Pump Control System

Hydro-Pneumatic / Pressure Operated Pump Control System

Features :

  • Operates on pressure switch condition
  • Wired Remote Indication Capability
  • Audio Visual Indication of Pump Fault
  • With or without VFD models available
  • Automation of up to 8 pumps in parallel
Applications :
  • All pressure booster systems used in domestic applications like tap water, shower, flush etc.
  • Sewerage treatment plants
  • Water purification plants
  • Boilers
  • HVAC applications
Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.

Sewerage / De-Watering Pump Controller System

Sewerage / De-Watering Pump Controller System

Features :

  • Completely Automatic Operation depending upon level
  • Protection provided for High Temperature (using TOP or PTC)
  • Protection provided for Gland Leakage (using moisture sensr)

Applications :
  • De-watering pumps installed at public places by government of private bodies
  • Portable De-watering pumps used by land development companies
  • De-watering pumps used at basements and low level areas by societies and residential complexes
  • Sewerage Pumps used by hotels and other buildings  
Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same. 

Fire Fighting Control System

Fire Fighting Control System

Features :

  • Modification in design as per the use of Main Sprinkler, Jockey and Diesel pumps
  • Automatic operation for all fire pumps
  • No Automatic OFF for Main Hydrant Pump
  • Facility for Stand by Pump can be provided
  • Completely Seperate Terminals for Stand-by Pump
Applications :
  • Fire Fighting pumping system controllers used in Malls, Hotels, Hospitals, residential compleses as well as all other buildings.

Common features & advantages of these systems over conventional systems are, 1) Our systems trips instantly at improper current sensing where as conventional systems need extra overload protection and it takes current dependent tripping time. 2) Our systems have longer life as there are no heating components where as conventional systems wear & tear due to continuous heating. 3) Our systems have inbuilt current sensors where as conventional systems require additional electronic circuit to be added in panel. 4) we have inbuilt digital current ampere meter and can display difference up to 0.1 Ampere where as extra moving coil ampere meter is required to be added in conventional system. 5) Voltage as well as Current based SPPis available in our system. Motor current gets affected when motor is not getting right voltage so any problem in supply line is sensed and motor is saved where as in conventional systems, SPP is Voltage Based. As Line voltage reaching the panel but not reaching the motor, this can not be sensed by voltage based SPP and so motor may burn. 6)  Our systems have Inbuilt Dry Run Sensor. Pump running dry is automatically sensed without the use of external liquid or flow sensor where as in conventional systems, extra electronic unit is required. It is not included as standard and they depend on the mechanical water or flow sensors. 7) In case of faults, fault finding is easy in our systems as there is a Digital Display of Faults. i.e. Direct reading of Fault on display. Hence easy and reliable fault location and removal  where as in conventional systems, there is no or premitive fault indication. Hence, fault finding is difficult and tedious 8) In our systems, we have less components, Less wiring and latest technology. Less number of components and less wiring means fewer maintenance issues, latest plug-in design makes it easy to change cards / parts and hence very less down time. In conventional systems, there is lot of wiring and complex wiring inside. More components and wiring means frequent maintenance requirements. Not easy to replace any part. 9) We have latest Micro-controller Technology. Highly reliable due to use of low voltage micro-controller control card and the use of best quality material. In conventional systems, there are analog components and limited reliability because reduced accuracy of analog components and finally 10) Our systems have inbuilt ON Timer & Off Timer where as in conventional systems, timers are not provided for pump or motor operation.These pump motor protector controller are marketed only thru dealers. Dealer enquiries are invited for the same.


 
 
 

Indiamart

Terms of Use - Privacy Policy - Link to Us

Copyright © 1996-2014 IndiaMART InterMESH Ltd. All rights reserved.