The ZX series of Mig welding are excellent machines. These produces uniform weld bead and low spatter due to its double star transformer with reactor and DCL. These have 16 voltage steps for output power setting by two switches, one for quick setting and another for fine setting. The combination of two switches are more durable rather than a single switch. The output brass terminals have been replaced with copper strip insulators. The wire feeder unit contains solid state motor drive brake and plug-in control circuit. 100% tested for non-stop work.

Features:

•  Double Star Transformer
• Soft Start Magnet DC Motor
• Quick Motor Stop
• Uniform OCV Steps
• Constant P.F.
• 3 Core Control Lead
• 125 Watt Heater
• Without Delay Welding Start

Technical Specifications:		Model
Item	Unit	ZX250	RX250	RX400
Supply	V	415 ± 10%	415 ± 10%	415 ± 10%
Phase	Ph	3	3	3
Frequency	Hz	50	50	50
Load	KVA	9.5	9.5	18
OCV (DC)	V	22-46	22-46	26-53
Output (Min./Max.)	A	60/250	60/250	80/400
Output Steps	Nos.	16	16	16
Control Circuit	V	24	24	24
Torch	X	AK-25	AK-25P	36-KDP
Motor	X	Permanent Magnet	Permanent Magnet	Permanent Magnet
Torch Connector	X	KZ-2	PM-3	PM-3
Weight	Kg	140	143	212
Key Feature:-	For Higher Production and RadioGraphic Welding.

The FINE TIG DX series of tig welders has trouble free highly durable design. These series have same electronic circuit board for every model. No manual tuning done at the time of assembling because PCB is manufactured from 1% tolerance components. Most simple operation, Only to set current and select TIG/STICK mode. Pre programmed "Post flow". Burden free quick setup.

Features:

•  Constant Current
•  Thyristor Control
•  Overload Protected
•  H.F. Start
•  Auto Post Flow
•  Torch Plug With Lock
•  Torch connection printed on machine

Technical Specifications:		Model
Item	Unit	FT300	FT400	FT500	DX300	DX400	DX500
Supply	V	415± 10%	415± 10%	415± 10%	415± 10%	415± 10%	415± 10%
Phase	Ph	3	3	3	3	3	3
Frequency	Hz	50	50	50	50	50	50
Load	KVA	14	20	26	14	20	26
Min. Current	A	30	30	40	15	20	30
Max. Current	A	300	400	500	300	400	500
OCV	V	102	102	113	108	108	108
Puls Freq	Hz	0.5-12	0.5-12	0.5-12	--	--	2-10
Puls Width	%	10-90	10-90	10-90	--	--	--
Weight	Kg	130	150	180	130	150	180
Key Feature:-	As mirror like finish, best for S.S., Copper and Titanium etc.

Now TCP series machines are standardized with DS33A synchronized panel. The anti-saturation technology has effectively dismiss the spark on job. High speed welding in "Auto Repeat" mode with a minimum of  0.02 second weld time. Synchronized linear Thyristor control power setting.

Features:

• Pneumatic Operated
• Synchronized Timers and Heat Control
• Single/Auto and Weld/No Weld Mode Selectable
• Thyristor Control.
• Copper Wound Transformer
• Water Cooled Electrodes

Technical Specifications:		Model
Item	Unit	TC15	TC20	TC30	TCP15	TCP20	TCP30
Supply	V	415± 10%	415± 10%	415± 10%	415± 10%	415± 10%	415± 10%
Phase	Ph	2	2	2	2	2	2
Frequency	Hz	50	50	50	50	50	50
Load	KVA	15	20	30	15	20	30
Thoat Depth	mm	280 ~ 330	280 ~ 330	280 ~ 330	350 ~ 400	350 ~ 400	350 ~ 400
Thoat Clearance	mm	190	190	250	250	250	250
Output Currentt	A	3800	4500	5600	3800	4500	5600
Weight	Kgf	128	128	128	232	232	232
Weight	Kg	230	280	320	250	300	340

Our seam welders gives full strength leakage free quality welding and very clear seam sign formation due to its new advance control panel. It welds synchronously silent without spark. All parameters seam size, weld on, plain/stitch, current are instantly settable in standby and also during welding. Its special cooling arrangement for job enhances electrode life as well as gives better welding results.

Features:

•  Jerk free smooth movement
•  Chromium Copper Electrodes
•  Water Cooled Transformer
•  Duel Insulated Transformer
•  Synchronous Control Panel
•  Thyristor Control
•  Direct Coupled Chain less Electrode Drive
•  Over Heat Protected.

Technical Specifications:		Model
Item	Unit	SMX100	SMX150	SMX200	SMY100
Supply	V	415± 10%	415± 10%	415± 10%	415± 10%
Phase	Ph	2	2	2	2
Frequency	Hz	0	50	50	50
Load	KVA	100	150	200	100
Welding Current	A	19,000	28,000	39,000	17,000
Standard Stroke	mm	100	100	100	100
Transformer & Electrode	Type	Water Cooled	Water Cooled	Water Cooled	Water Cooled
Water Supply	L/min.	30	30	30	30
Key Feature:-	Leakage free higher strength weld results.

Special body shape for safe torch terminals and workconnection. Single board plug-in electronics circuit with durable components (relay life > 10,000,000 operations). All function starts from cutting torch switch with addition torch cooling time. Machine stops working during low air or no air. It has long pilot arc which starts cutting operation quickly.

Features:

• Low Pressure Shut Down.
• Filter Regulator at Back of machine
• Long Pilot Arc
• Pressure Gauge on Front
• Phase Indicators.
• Big Waning Light
• Heavy Duty Transformer
• Special H.F. Protection Circuit

Technical Specifications:		Model
Item	Unit	PC60	PC100
Supply	V	415± 10%	415± 10%
Phase	Ph.	3	3
Frequency	Hz	50	50
Load	KVA	15.5	26
OCV	V	320	320
Duty	%	60	60
Current	A	60	100
Cutting Depth	mm	18	25
Weight	Kg	153	200

Resistance Heaters are essential in U-bolt units for pollution free workshop. We have both electronic and electrical machines, This one is Pneumatic operated electronic machine for higher production. It's inside control panel placement makes it highly durable  because of no external control wiring. It has 0.02 to 280 second digital heating time setting with heat of function. Transformer secondary have hollow construction for maximum cooling and electrodes have designed to flow extra coolant this enhance electrode and transformer life.

Features:

• Synchronized Heating Timer
• Fast Pneumatic clamping
• Heat Delay Adjustable
• Thyristor Control Step less Power Setting
• Extra Cooling Protect Transformer & Electrode from Scaling
• Heating Time from 0.02 to 199.98 seconds in 9999 steps

Technical Specifications:		Model
Item	Unit	Model : HRP3xxx	Model : HRCxxx
Supply	V	415± 10%	415± 10%
Phase	Ph	2	2
Frequency	Hz	50	50
Load	KVA	30 to 100	30 to 100
Rod Length	X	1)	1)
Rod Dia	X	1)	1)
Thyristor	X	Yes	No
Timer	X	Yes	Optional
Pneumatic Clamping	X	Yes	No
Key Feature:-	Enviornment friendly and noise free.
1) Application Specific, Call for more details.

Stored Energy Welders also known as Capacitor discharge welders have created attraction in industry by their low power demand and three phase balance load. A 10 KVA  Stored Energy welder can easily weld the component of 50KVA traditional projection welder.Old model was AP11, This is new model SE12 comes with all improvements
like new Advanced Control Circuit, Modified Transformer, Hydraulic Mechanism and In Panel Counter.

Features:

• 450 Volt Discharge Proof Capacitors
• On Top Hydraulic Power Pack
• Power of Capacitor Discharge
• Voltmeter & Counter on Panel
• Charging Indicator
• Adjustable Weld Delay
• Constant Charging Current

Technical Specifications:		Model
Item	Unit	SE 12/7	SE 12/10	SE 12/20	AP15
Supply	V	415V± 10%	415V± 10%	415V± 10%	415V± 10%
Phase	Ph.	3	3	3	3
Power	KVA	7.5	10	20	2
Stored Energy	Jule	5500	8500	13000	--
Clamping	Type.	Hydraulic	Hydraulic	Hydraulic	Hydraulic
Clamping Force	Kgf.	1550	1550	2200	200
Max Charging Time	Sec.	2.5	3	2.5	3
Throat Depth	Inches	8	8	10	6
Capacitor Coolinh	Type	Forced Ait	Forced Air	Forced Air	--
Dimention H.D.W	Inches cm.	92,71,18 234,180,46	92,71,18 234,180,46	92,71,22 234,180,56	--
Weight	Kg.	--	1050	--	350
Key Feature	Lower power consumption than traditional projection welders.

Our machines give perfect controlled grain flow of metal.These are Pneumatic operated for maintenance free work. Electronic user friendly control panel with Asynchronous
heat and delay timer. Smooth job movement and fine thyristoried heat control gives uniform and flawless gathering results.

Features:

• Plug-in PCB's
• On Panel Volts and Counter Meter
• Thyristoried Power Control
• Gold Flush Contact Switches
• Air Cooled Heavy Duty Thyristor Assembly
• Transformer & Electrodes Water Cooled
• Overheat Protection
• Video Testing and Operational Manual

Technical Specifications:		Model
Item	Unit	SMG30	SMG45
Supply	V	415± 10%	415± 10%
Phase	Ph.	2	2
Frequency	Hz	50	50
Load	KVA	30	45
Max. Diameter of Rod	mm	16	30
Max. Dia. of Gathered Head	mm	40	80
Max. Gathering Force	Kgf.	2100	4000
Max. Length of Gathered Head	mm	60	75
Clamping Force	Kgf.	85	85
Weight	Kg	950	1100
Key Feature:-	Noise free and environment friendly against oil furnaces and UP-Setters.

We manufacture all type of scaffolding welding petitioners. All models are easy operate able for higher production.

Features:

• Space Saving Design
• Specially Designed Inbuilt MIG Machine
• Three Phase Supply only without Neutral

Technical Specifications:
Work Piece Weight	= 0 to 5 Kg.
Speed	2 to 10 RPM
Rated Supply	210V ±10% 1Ph. 50 Hz.
All other specifications will be on request .

SOHAL TCR 250 / TCR400 Welding rectifiers built using state-of-the-art Thyristor technology. Welding Rectifiers as their name are Direct Current Welding Machines overcome from AC Welding Machines by higher strength,better finish, lower spatter and radiographic Welding possibility. These machines are designed as to consume minimum electricity, robust construction, user friendly and for continuous welding. The major applications include,  i.e., Steel Plants, Structural Fabrication, Mill sheds, Die Repair and special ferrous and nonferrous Welding.

Features:

• Front Panel Ammeter
• Constant Current
• Minimized Spatter
• H.F. Unit Compatible
• Optional Remote Current Control
• No Effect of 10% Supply Fluctations

Technical Specifications:		Model
Item	Unit	RRL300	RRL400	RRL600	TCR250	TCR400
Supply	V	415± 10%	415± 10%	415± 10%	415± 10%	415± 10%
Phase	Ph	3	3	3	3	3
Frequency	Hz	50	50	50	50	50
Load	KVA	14	19	25	13	21
OCV (DC)	V	60	65	70	100	110
Output (Min.)	A	60	80	100	20	20
Output (Max.)	A	250	350	400	250	400
Strike (Max.)	A	300	400	500	250	400
Current Steps	Nos.	Stepless	Stepless	Stepless	Stepless	Stepless
Suitable Electrode	mm	2.5, 3.15, 4	3.15, 4, 5	3.15, 4, 5	2.0, 2.5, 3.15, 4	2.0, 2.5, 3.15, 4, 5
Weight	Kg	210	240	280	120	145

BW15 Butt Welding is specially designed for higher production up to 8000 pieces per shift. Electronic "time and current" control panel. Pneumatic clamping and forg, fast job removal.

Features:

• Thyristoried Current Control
• Pneumatic Operated
• Higher Production
• Transformer & Electrode Air-Cooled

Technical Specifications:		Model
Item	Unit	BW15	BZ60	BR40
Supply	V	415± 10%	415± 10%	415± 10%
Phase	Ph	2	2	2
Frequency	Hz	50	50	50
Clamping	Type	Pneumatic	Pneumatic	Pneumatic
Forge	Type	Pneumatic	Pneumatic	Pneumatic
Secondary Curr.	A	2500	12000	9000
Transformer & Electrode	Type	Water Cooled	Water Cooled	Water Cooled
Curr. Control	X	Thyristor Cont.	Thyristor Cont.	Thyristor Cont.

PJS series machines are standardized with DS33 synchronized panel. The antisaturation technology has effectively dismiss the spark on job. High speed welding in "Auto Repeat" mode with a minimum of  0.02 second weld time. Synchronized linear Thyristor control power setting.

Features:

• Pneumatic Operated
• Synchronized Timers and Heat Control
• Single/Auto and Weld/No Weld Mode Selectable
• Thyristor Control.
• Copper Wound Transformer
• Water Cooled Electrodes

Technical Specifications:		Model
Item	Unit	PJS50	PJS75	PJS100	PJS150	PJS200	PJR50
Supply	V	400 ± 10%	400 ± 10%	400 ± 10%	400 ± 10%	400 ± 10%	400 ± 10%
Phase	Ph	2	2	2	2	2	2
Frequency	Hz	50	50	50	50	50	50
Load	KVA	50	75	100	150	200	50
Nominal Center	mm	255	255	305	305	305	610
Pilar	X	Hallow	Hallow	Solid	Solid	Solid	Hallow
Welding Curr.	KA	15	22	30	45	75	14
Transformer	X	Water Cooled	Water Cooled	Water Cooled	Water Cooled	Water Cooled	Air Cooled
Nominal Panel	X	DS33	DS33	DS33	DS33	DS33	DS33