Fibre Optic Cables & Patch Cords

Clipsal 1U Enclosure accomodates patch cord & pigtail storage. It is an effective solution for limited space environmnets.

These Hook & Loop Tape Fasteners are made from superior quality yarns to ensure long life and better peel & shear strength.

The Hook side is the rough or hard side, while the Loop side is the soft or fuzzy side and both are fastened together to create a bond.

The Clipsal Connection Modules are Krone Backmount Frame compatible. Accessories available add further convenience and safety to the Clipsal Voice Connection Range.

Right Angle Plug to Jack Adaptor for 50 Ohm BNC

• BNC Male Straight Crimp type Connector for RG58 Thinnet.

• Available 50 Ohm BNC & 75 Ohms

• BNC Male Crimp connector for RG62. Crimp Style 3 Piece with Gold Plated Brass Contact, Nickel Body Plating, and Polyethylene Dielectric.

An easy way to terminate coaxial cables, no soldering or special tools needed. One piece construction simplies attachment. Nickel plated with gold-plated center pin for the best conductivity. Twist on connectors are recommended for use with coaxial cable that utilizes a solid center coductor.

• A Solder BNC Female Connector that can be instald/mounted in a panel

Clipsal Category 5, 25 Pair Cable is constructed of 24AWG (0.5mm) solid-copper conductors insulated with high density polethylene. The insulated condoctors are tightly twisted into pairs, stranded into mini-units. The calbe employs a unique honeycomb core construction. This design consists of multiple 3-Pair and 4-Pair tightly braided sub-units. A total of seven uncovered sub-units (six around one) are then braided to encompass the cable core. This construction allows for easy pair identification and subsequent termination.

These Hook & Loop Tape Fasteners are made from superior quality yarns to ensure long life and better peel & shear strength.

Special Features

* TBT level under tolerance
* Superior quality Azo-free dyes
* Dye to match facility available
* Guaranteed width & length
* Excellent color fastness, washable & can be dry cleaned
* Available in over 80 different colors
* Resistant to heat, chill, acid & alkalis
* Easy to cut into various shapes & size
* Easy to install by sewing, sticking or welding
* High durability, a better alternative over buckles & zippers
* High endurance to heat.

Avilable Sizes: 20 X 200

Avilable Colors: Orange, Yellow, Green. We can supply any Colors on request.

the clipsal distribution enclosures can be used as eigher a floor distributor (idf) or a final distribution point (fdp). Weatherproof enclosures for use as campus or building distributors (mdf) are also available. Record cards and keyed locks are lncluded.

• BNC coupler enables two coaxial cables fitted with male BNC plugs to be coupled together.
• Cal also be used as a gender chaner connectors.

LC Attenuators

Available Ratings:

5dB, 10dB, 20dB

• An easy way to terminate coaxial cables, no soldering or special tools needed. One pice construction simplifies attachment.
• Twist on connectors are recommended for use with coaxial cable that utilizes a solid center coductor.

• Used for combining/splicing sgnals.
• This "T" is plugged into the BNC network card in a thinnet network.
• A terminator must be attached to the two "T"s at the end of the network.c

The Connect 6 Patch Panel is fully loaded with Category 6, 180Degree, Kaystone Jacks. This Patch Panel consists of a metal frame construction with ABS fascia, bracket and cable mamagement tray. It is poder coated for protection against scratches and rust.

For ordering information please go thru the pdf document.

The Clipsal Category 3 Low Smoke Zero Halogen (LSZH) Cable has the same electrical and performance charateristics as Category 3 Multipair LAN Cable but has additional feature of being insulated with non-halogen high-density polythyne and covered with low smoke zero halogen compounds.

The Clipsal Distribution Frames are available for use as a Campus Distributor or Building Distributor (MDFs), Floor Distributor (IDF) or Final Distribution Point (FDP)

This is a female/femal coupler that can installed mounted in a panel