Industrial Nozzles

Full cone nozzles for continuous casters produce a full cone spray pattern, with a uniform liquid distribution. The special design of the internal vane ensures a good resistance to clogging. Typical application continuous casting machines.

Characteristic : These nozzles produce a uniform liquid distribution.

Spray angle : 30⁰ to 90⁰

Flow rate (LPM) at 2.8 bar Pressure : 1LPM to 12 LPM

Connection : 1/4", 3/8" BSP (f) 

M.O.C. : Brass, SS, 316, 304
 

Air atomizing spray nozzles make use of collision of sir and liquid to provide an atomized spray. It comes in various nozzle designs that suit different applications which are as follows:

• Coating
• Gas cooling
• Conditioning or humidifying
• Atomizing of viscous liquids
• Chemical process engineering

Its specifications are listed below:

• It has spray angle of 15, 20, 25, 45, 60, 90, 120 degrees
• The flow rate that it offers is 0.05 to 6

The connection specification is as follows: 1/4” to ¾”BSPT/ NPT or BSP,/b>

Wide angle flat jet with sharply defined spray pattern.

Tank cleaning spray nozzles are mainly used for cleaning tanks and vessels. It is useful in tackling the following problem areas such as high cost of labor involvement, increased sanitary requirements, disposal problems of contaminated cleaning solutions and safety requirements at work for cleaning solvents Its application areas are mentioned below:

• Cleaning of barrels and tanks
• Introduction of stream into tanks
• For circulation of liquids in chemical processes to enhance reactions
• Aeration of bulk material by injection of compressed air

Its specifications are listed below:

Spray angle comes in the following angles 120, 180, 240, 270, 300, 360 degrees

• Flow rate at 2 bar pressure is from 10 to 1120
• The connection specifications are ½” to 3” BSPT/ NPT or BSP
• Stationary type is also available.

This tangential entry hollow cone spray nozzles gives a circular ring of liquid. These are ideal for good atomization of liquids at lower pressure or when the quick heat transfer is needed. These facilitate unhampered flow without clogging. Tangential type offers a nozzle free passage to the liquid and has the following application sectors:

• Cooling, conditioning, cleaning
• Water cooling
• Cooling of tanks
• Air washers
• Chemical engineering
• Dust suppression
• Foam control
• Fire fighting.

Its specifications are listed below:

• Spray angle is available in the given ranges 45, 60, 80, 90, 120, 130 degrees.
• The flow rate at 2 bar pressure is from 1 to 1200
• Connection available is ¼” to 4” BSPT/ NPT or BSP

Full cone spray nozzles from complete spray coverage in a round or square shaped area. It provides an uniform spray distribution of medium to large size drops resulting from their vane design which features large flow passage and control characteristics. This is extensively used in industry.

Characteristic : Internal vane design features large flow passage and fine control

Design : Removable Vane

Type : Round pattern, Square Pattern, Oval Soild Cone, Wall Mounted type.

Application : Surface spraying, washing & cooling of flue gasses to remove fly ash, cooling condenser, Scrubbing, Foam Breaking.

Flow Rate : 1 LPM to 8000 LPM

Pressure : 2.0 Kg/cm² or specified

Spray Angle : 30^0, 120⁰

End Connection : 1/ 8" to 4" BSPT/ NPT or BSP-Flanged  

M.O.C.: S.S. 316, 304, Brass, PVC, PVDF, PP, Teflon

The spiral full cone spray nozzles is a combination of small sizes with wide flow openings. These are essentially non clogging as these have no internal parts. It has applications in gas washing, cooling towers and fire fighting systems. Its specifications are listed below: Spray angle is available in the following ranges 60, 90, 120, 150, 180 degrees The flow rate at 2 bar pressure is from 10 to 4000 The connection available is 3/ 8” to 4” BSPT/ NPT or BSP flanged

Multiple Full Cone Nozzle

This type of nozzle gives a fine atomization with the help of several hollow cones that spray in to each other. Its areas of applications are stated below:

• Cooling of gaseous and solid material
• De super heaters
• Chlorine precipitation
• Improving of chemical reaction by magnifying the contact surface

Its specifications are stated below:

Spray angle comes in 70, 90, 120, 130 degrees the flow rate at 2 bar pressure is 6 to 70 The connection specifications is as follows: ½” to 1” BSPT/ NPT or BSP

Fog Jet  spray nozzle

It offers a spray of small sized drops that have a dense full cone type pattern with large flow rates. It finds applications in the following areas:

• Fire protection
• Dust control
• Aerating
• Chemical processing industry

Its specifications are as follows:

It has the spray angle of The flow rate at 2 bar pressure is 16 to 225 The connection specification is as follows:3/4” tp 1 ½” BSPT(f) or BSP

Solid jet spray nozzles gives a compact stream jet with a defined jet length due to the optimum flow geometry. It is demanded for its efficient and economical performance. It is not affected by turbulence and a high impact force is always achieved. It is mainly useful in the area where concentrated jet power is of importance. Its sector of applicationsa is mentioned below:

• High pressure
• cleaning systems
• Jet cutting and separating

Its specifications are as follows:

• Spray angle is 0 degrees
• Flow rate at 2 bar pressure ranges from 1to 300
• The connection details are 1/8” to 1” BSPT/ NPT or BSP

Flat Jet Nozzles/ Flat Jet Spray Nozzles

As the name implies, the spray pattern appears as a flat sheet of liquid. The flow geometry provides uniform spray pattern & high impact, for various spray angles to satisfy various applications.

Characteristic: They are non-clogging and can operate through pressure fluctuations.

Design: One piece construction, Non clogging type.

Application : Surface Treatment, Roll Cooling, Degreasing and Rinsing, Lubricating, Industrial washing machines, ect.

Flow Rate : 1 LPM to 280 LPM

Pressure : 2.0 Kg/cm² or specified 

Spray Angle : 15⁰, 120⁰

End Connection : 1/8" to 2" Brass, PVC, PP, Teflon PVDF, ect.

Flat Spray Nozzles With Dove Tail Design 

Uniform parabolic distribution of liquid. Headers, equipped with these nozzles, show a highly uniform total distribution of liquids, even at different installation heights and centers. Nozzle position fixed by self-setting dove-tail Flat jet preset at 15⁰ and 5⁰ pipe axis.

Characteristic : Uniform flat spray with knife-like cutting edge. accurate jet alignment.

Application :  Roll Cooling, Descaling, High pressure Cleaning etc.

Range:

Spray angle :  15⁰ to 120⁰

Flow rate : 1 to 100 LPM

Pressure : 2.0kg/cm² or specified

Connection : Mounted with Aid of Dovetail Fixing Dovetail Nipple & Retaining Nut.

Standard Accessories : welding nipple and screwed nut