In the flat jet spray nozzle the pattern of the sprayed droplets appears as a flat sheet of liquid. The flow geometry facilitates uniform spray pattern and has impact for various spray angles that are required for various applications. The special features of our flat jet spray nozzles are listed below:
Non clogging
Efficiently handle pressure fluctuations
Offer a variety of spray angles (20, 30.45, 60, 80, 90, 120 degrees)
Flow rate at 2 bar pressure ranges from 0.5 to 280
The connection specification is 1/8” to 2” BSPT/NPT or BSP
These are required in many sectors such as surface treatment, roll cooling, high impact washing, degreasing, rinsing, washing crushed stone, gravel sand, spray costing and lubricating.

The descaler flat spray nozzle gives a uniform flat spray with knife like cutting edge and accurate jet alignment. It has the following features:

• Maximum impinging force
• Minimum loss of energy
• Forms dove tail design
• Varied spray angles such as 15,25,30, 45 degrees
• High flow rate at 100 bar pressure that ranges from 12 to 150
• Standard accessories are welding nipple and screwed nut.

These can be used for descaling and high pressure cleaning.

The full cone spray nozzle gives complete spray coverage in a round or square shaped area. It provides medium to large size drops and features large flow passages and control character sticks. It is mainly used in style industries how ever other applications are listed below:

• Washing
• Rinsing
• Quenching and cooling of coke, metal and other materials
• Suppression of fugitive dust
• Deluging combustible dust

Scrubbing washing and cooling of the fuel gases in many industries mainly steel making and machine making industries
To fly away ash and other end products of combustion

Its features are as follows:.
Varied spray angles such as 30,45,60,80,90,110,120 degrees
Flow rate at 2 bar pressure is from 1 to 8000
The connection specifications are 1/8” to 4” BSPT/NPT or BSP flanged

This spray nozzle is a combination of small sizes with wide flow openings. These are essentially non clogging as these have no internal parts. It has applications in gas washing, cooling towers and fire fighting systems. Its specifications are listed below:

Spray angle is available in the following ranges 60,90,120,150,180 degrees
The flow rate at 2 bar pressure is from 10 to 4000
The connection available is 3/8” to 4” BSPT/NPT or BSP flanged

This gives a circular ring of liquid. These are ideal for good atomization of liquids ay lower pressure or when the quick heat transfer is needed. These facilitate unhampered flow without clogging. Tangential type offers a nozzle free passage to the liquid and has the following application sectors:

• Cooling, conditioning, cleaning
• Water cooling
• Cooling of tanks
• Air washers
• Chemical engineering
• Dust suppression
• Foam control
• Fire fighting.

Its specifications are listed below:

• Spray angle is available in the given ranges 45,60,80,90,120, 130 degrees
• The flow rate at 2 bar pressure is from 1to 1200
• Connection available is ¼” to 4” BSPT/NPT or BSP

Through this type of nozzle the supply of liquid takes place axially and form fine uniform hollow corn spray pattern. The sectors where it finds its usage are given below:

• Cooling and cleaning of air
• Spray drying
• De superheating
• Metal treatment
• Brine spraying

Its specifications are stated below:
It has spray angle that comes in the following ranges: 45,60,80,90,120 degrees
The flow rate at 2 bar pressure is 1 to 40
The connection specifications are 3/8” to ½ “ BSPT/NPT or BSP

It gives a compact stream jet with a defined jet length due to the optimum flow geometry. It is demanded for its efficient and economical performance. It is not affected by turbulence and a high impact force is always achieved. It is mainly useful in the area where concentrated jet power is of importance. Its sector of applicationsa is mentioned below:

• High pressure
• cleaning systems
• Jet cutting and separating

Its specifications are as follows:

• Spray angle is 0 degrees
• Flow rate at 2 bar pressure ranges from 1to 300
• The connection details are 1/8” to 1” BSPT/NPT or BSP

These are mainly used for cleaning tanks and vessels. It is useful in tackling the following problem areas such as high cost of labor involvement, increased sanitary requirements, disposal problems of contaminated cleaning solutions and safety requirements at work for cleaning solvents
Its application areas are mentioned below:

• Cleaning of barrels and tanks
• Introduction of stream into tanks
• For circulation of liquids in chemical processes to enhance reactions
• aeration of bulk material by injection of compressed air

Its specifications are listed below:

Spray angle comes in the following angles 120,180,240,270,300,360 degrees
• Flow rate at 2 bar pressure is from 10 to 1120
• The connection specifications are ½” to 3” BSPT/NPT or BSP
• 
  Stationary type is also available.

It makes use of collision of sir and liquid to provide an atomized spray. It comes in various nozzle designs that suit different applications which are as follows:

• Coating
• Gas cooling
• Conditioning or humidifying
• Atomizing of viscous liquids
• Chemical process engineering

Its specifications are listed below:

• It has spray angle of 15,20,25,45,60,90,120 degrees
• The flow rate that it offers is 0.05 to 6

The connection specification is as follows: 1/4” to ¾”BSPT/NPT or BSP,/b>

The cooling of hot strand is very crucial and this is exactly what this nozzle is used for. It gives a uniform distribution of cooling water and quick removal of cooling water from the strand surface which is considered important for fine quality steel.

Its specifications are listed below:

• It has the spray angle of 60, 75, 90,120 degrees.
• The flow rate it offers at 2 bar pressure is from 1 to 40
• The connection specification is dependent on the site conditions

It offers a spray of small sized drops that have a dense full cone type pattern with large flow rates. It finds applications in the following areas:

• Fire protection
• Dust control
• Aerating
• Chemical processing industry

Its specifications are as follows:
It has the spray angle of
The flow rate at 2 bar pressure is 16 to 225
The connection specification is as follows:3/4” tp 1 ½” BSPT(f) or BSP

This type of nozzle gives a fine atomization with the help of several hollow cones that spray in to each other. Its areas of applications are stated below:

• Cooling of gaseous and solid material
• De super heaters
• Chlorine precipitation
• Improving of chemical reaction by magnifying the contact surface

Its specifications are stated below:
Spray angle comes in 70,90,120,130 degrees
the flow rate at 2 bar pressure is 6 to 70
The connection specifications is as follows: ½” to 1” BSPT/NPT or BSP