	All the product contact parts are made from Stainless Steel corresponding to SS 316
	Non-contact parts and outer surfaces made from Stainless Steel corresponding to SS 304.
	All doors, safety guards and covers are provided with a suitable food grade seals
	Pan speed 1 to 15 RPM
	Perforated pan with more than 53% perforation opening for process optimization and to reduce the losses while during the process
	Pan speed control via variable frequency flux vector control AC Drive
	Tablet discharging facility will be through the special diverter assembly
	On the front Stainless steel cover with a glass door for process visualization.

Inlet Air Handling Unit

	Supply air Fan (Control Through Frequency Drive)
	Chill Water Coil
	Steam Heating Coil
	Pre Filters
	Micro Vee Filters
	HEPA Filters

Fluid Bed Dryer

Technical Specification

	Fluidized Bed Chamber [Main Housing], retarding chamber and filter bag housing made from Stainless Steel grade SS 316
	Chamber will be provided with an inspection window duly sealed with toughened glass
	Chamber will be provided with a light window duly sealed with toughened glass
	Filter Bag fixing through SS Fixing ring and equipped with an inflatable seal
	Pneumatically operated Inflatable seals with electro-pneumatic signaling device to ensure fail-safe operation
	Inner surface of the container will be mirror finished
	Outer surface of the container will be 180 grit finished
	Waste Water Drain is provided on the Bottom chamber for ease of cleaning
	Basic equipments with PLC.

Lifter

Technical Specification

	Lifter is designed with considering the loading capacity
	Lifter is specially designed for lifting of IBC / IPC / BINS
	IBC holding arm will be made of AISI 304
	Main structure will be made of AISI 304 and covered with SS 304 guard
	Main control panel will fixed on main pillar in construction of SS 304
	lifter is designed on hydraulic system.
	Mounting of lifter main structure is on base plate with bearing support at bottom and top end , bottom plate will be fixed on ground floor with anchor fastener Or Solid J bolt grouting.
	Top end of lifter main structure is on bearing and will be fixed in ceiling
	For up and down position of lifter there will be a limit switch for safety
	Surface finish will be matt
	Front side will be covered with flexible belt.

Octagonal Blenders ( Vacuum Rated)

Technical Specification

	Any blender will be in a Vacuum rated design
	Complete structure will be made from SS 304 & covered with SS - 304
	All the contact parts made of SS – 316
	All the non contact parts will be made of SS – 304
	Discharge out put Via. manually operated butter fly valve
	Standard dust proof control panel made of SS – 304
	Driving end will be cover from SS – 304 guards
	Inside mirror finish with buff
	Out side mat finish.

Optionals For Octagonal Blander

	Flame Proof Construction
	Documentation:
	PLC control panel

Paste Kettle

Technical Specification

	Hemispherical design for proper mixing of paste
	Jacket for heating element as a part of kettle
	External jacket for Insulation as an option
	Heating element via steam ( Provided by customer)
	Discharge from bottom via butter fly valve
	Inside mirror finish
	Driven via motor & gear box assembly mounted on top
	Discharge of paste Via. Bottom from butter fly valve
	Anchor type impeller design for proper mixing of paste
	75% closed & 25 % open top cover deign with proper locking
	All the contact part from SS-316
	All the non contact part from SS- 304
	Main pillar of Kettle will be from SS 304
	Operating panel will be fixed on pillar.

Pharmaceutical Conveying System

Powder conveying system

Pharmaceutical Machinery

Get complete information on various pharmaceutical machines like processing machines

Rapid Mixture Granulator

Technical Specification

	All the product contact parts are made from Stainless Steel SS 316 & non contact from SS 304
	All doors, safety guards and covers are provided with a suitable food grade seals
	4- Blade Impeller Design for efficient mixing as a standard,
	Granulation blade laterally mounted with a 4- blade design to have a better granulation
	Binder charging port will be provided on the Top lid of the bowl with binder charging funnel and ball valve manufactured from SS-316
	Glass window will be provided at the top lid for process visualization from SS-316 and Food grade material
	2 nos.- 2” Tri-clover joint with a blind ferrules will be provided at the top lid for Material charging system
	Filter assembly will be provided on top lid in Stainless steel housing
	Pneumatically operated Top Lid & Discharge gate with Electro-pneumatic positioning for fail safe operation and operator safety
	Top lid & Discharge gate opening and closing with Non contact magnetic switch/ Proximity switch, and interlocked with central control system
	Main structure will be manufactured from heavy duty square MS tube with paint and is covered with SS 304 guard
	Stair case , platform and main structure will be covered from SS 304 chequered sheet
	Control console Via. PLC based controls.

Single Bowl Processor

Technical Specification

	All the product contact parts are made from Stainless Steel SS 316
	Non-contact parts and outer surfaces made from Stainless Steel SS 304.
	3- Blade Impeller Design for efficient mixing as a standard
	Chopper blade mounted on a top lid with a 4- blade design to have a better granulation
	Impeller blade positioning through position sensor,
	Binder charging port& toughened glass provided on the Top lid
	Multi filter Assembly in Stainless steel housing with a connection the equipment to Vacuum system with a air blasted filter clean system
	Bowl is having jacket design for supply of steam, hot water and/or cold water, as a heating / cooling media
	Control console/ Operator with 7.5” Color Touch screen based graphical user interface with flame-proof compliance
	Programmable Logic Controller, Touch Screen based operator Interface are of Allen-Bradley or Equivalent Make
	All the Pneumatic components are of “Festo” or Equivalent make
	In built Compressed air unit
	Seal purge will be facilitate to have purging of Air or Nitegron
	Scrubber system is with condensation tower is inbuilt with basic machine
	Solvent recovery vessel is a part of machine.

Tablet Deduster

Technical Specification

	Tablet Output	5,000 to 2,00,000 Tablets/ Hour (Depending upon size and speed)
	Contact Parts	Manufactured from Stainless Steel 316
	Electric Power	0.18 KW, 3 Phase, 415 VAC, 50 Hz
	Maximum Tablet Diameter	36 mm
	Minimum Tablet Diameter	5 mm
	Net Weight	115 Kgs.
	Overall Dimension	400 mm (L) X 400 mm (B) X 800 mm (H)
	Through Put of Tablet	5 to 120 Seconds (Depending upon the size and speed)

SALIENT FEATURES

	Efficient De dusting and is suitable for high speed tablet machine
	Tablet outlet speed will be of 26 to 35 second from top to bottom finally it depends up on shape size and weight of tablet
	All the contact parts are manufactured from Stainless Steel SS 316
	All the non-contact parts are manufactured from Stainless Steel SS 304
	De Duster works on the principle of Rotary vibratory action
	Single Phase- Un balance vibro-motor for better vibration amplitude
	DOL Starter on the machine for ease of operation
	Very low Electrical power consumption
	Very low noise level
	No moving component, Hence almost maintenance free
	Height adjustment RAM Assembly to adjust the Tablet Press output discharge
	Do not require any tool for cleaning
	Tablet de-dusting route is geometrically designed as to achieve optimum de- dusting.

Different Models
08 tray model ( Suitable for High Speed tablet Press )
Transparent Guard
Dual motor with frequency drive in 08 tray model
04 tray model ( Suitable for Medium Speed tablet Press )
SS 304 Guard
Single motor with out frequency drive
Top to bottom ( Suitable for Medium Speed tablet Press )
SS 304 Guard
Single motor with out frequency drive

Vibro Sifter

Vibro Sifter (Vaccum Rated)

Technical Specification

	Basic Equipment in vacuum rated designed & is enabled for inline sifting process
	Vibro sifter works on specially designed unbalance Vibro-motor
	Detachable sieve design to accommodate user’s requirements
	Mounted on set of heavy duty spring and metal plate
	All contact parts are manufactured from SS-316
	All non-contact parts are manufactured from SS-304
	All the gasket and seals manufactured from food grade sealing
	Equipment in trolley based design with PU castors for ease of movement
	Very low noise level
	All the cleaning parts can be easily open able without the use of spanner
	Easy to clean
	Material charging pot will be provided for Manual loading
	Output will be approximately 100 to 150 Kgs./ Hour depending upon the mesh size and material density.

Utility Requirement

440 volts, 50 Hz, 3 phase , 4 Wire System, 1 HP Power Connection.

Wash In Place System

Technical Specification

	WIP System in Trolley based design mounted on a set of UHMW tiring for ease of movement
	WIP system structure manufactured from stainless steel SS 304 so as to maintain environmental hygiene
	System is equipped with high-pressure pump with a displacement rate of 1200 LPH manufactured from stainless steel SS 316 and driven via a flameproof electrical motor
	Equipped to accommodate- Potable Water, Hot Water and Purified Water cycles
	All the valves are manufactured from Stainless Steel SS316
	WIP System is having a 10 Liter detergent tank with a detergent cycle valve manufactured from stainless steel SS316
	All the pipes and fittings are manufactured from stainless steel SS 316 and are electro polished from inside and outer surface is mirror polished
	System control via Programmable Logic Controller and 3” Graphical User interface
	Temperature control probe will be installed in hot water connection line to measure and record temperatures
	System is having capability to handle up to 10 Recipe for user specific requirement.

Other products & services we offer

Pneumatic Conveying System Type 1

Pneumatic Conveying System Type 2

Tray Tablet Deduster