Success Hydroparts Private Limited

General Features

1. Direct Operated Valve.

2. Puppet with cushion technic, avoids hammering.

3. Available as cartridge valve, threaded port connection & subplate mounted.

4. Two type of Pressure Setting

(a) Knob without lock (b) Knob with

Electrically operated direction control val Type LR - 06 (cetop -3) GENERAL FEATURE 1. Porting pattern as per international standards like CETOP, ISO 2. Oil immersed solenoid with indexable coil to any position & can be easily replaced by opening the knob. 3. Hand emergency is a standard feature 4. AC & DC both voltage. 5. Electrical connection through plug in connector. 6. Direct operated valve.

Pilot Operated Pressure relief Valve

Type PRP

 

General Features

1. PRP is pilot operated poppet type pressure relief valves.

2. Sub plate mounting valve.

3. Solenoid unloading.

4. Two type adjustment

(a) Hand knob, (b) Set screw with check nut,

 

 

Type PRP

System pressure acts on the main poppet. At the same time pressure acts via apilot on the spring loaded side the main poppet and on the pilot poppet. If system pressure exceeds the value set with the spring, the pilot poppet open, and pilot oil is allowed to flow return to tank. The pilot causes a pressure drop at the main poppet. This is lifted formits seats and opens the connection pump to tank, while operating pressure drop at the main poppet. This is lifted formits seat and opens the connection pump to tank while operating pressure is mainted in system.

 

 

General Features

1. SCG is Pressure Control Valve.

2. Sub plate mounting valve.

3. Four type Valve.

(1) Counter Balance Valve (Internal Pilot - Internal Drain)

(2) Counter Balance Valve (External Pilot - Internal Drain)

(3) Sequence & Check Valve. (Internal Pilot - External Drain)

(4) Sequence & Check Valve. (External Pilot - External Drain)

TECHNICAL DATA

General

Ambient temperature	Up to 50 C
Fluid temperature	Up to 80° C
Weight of valve	7.5 Kg
Mounting bolt	M10x80L(4 nos.)

 

Hydraulic

Operating pressure	210 bar
Flow LPM	125
Fluid	Mineral Oil/Phosphate ester
Viscosity	2.8 to 300 mm2/sec.
Filteration	20 micron
Pressure Adjustment Range	A-2.5-4.5 B - 4.5 – 9 D- 18-35 E - 35 – 70 F-70- 140

 

 

General Features

1. PRC is Pressure Reducing & Check Valv

2. Sub plate mounting valve.

 

General

Ambient temperature	Up to 50 C
Fluid temperature	Up to 80 C
Weight of valve	8.5 Kg
Mounting bolt	M10x80L(4 nos.)

Hydraulic		Max. Flow
Operating pressure	210 bar	Set Pressure (bar)	Max. Flow (Lpm)
Flow LPM	50, 100, 125	7-10 10-15 15-205	50 100 125
Fluid	Mineral Oil/Phosphate ester
Viscosity	2.8 to 300 mm2/sec.
Filteration	20 micron
Pressure Adjustment Range	A - 7 - 70 B-35-140 C - 70 - 205

Type PRC is Pressure Reducing & Check Valves are used to set the Pressure of a hydraulk cuit below that of the main Circuit. They have Check Valves, Which allow a Free Flow From the Secondary Side j Primary. Operation under Remote Controle is also Possible by using the Remote Control Port.

 

 

Radial Piston Pump Type RP

General Features:-

1. Radial Piston Pump with 3,5,7 pumping piston construction.

2. Fixed delivery pump.

3. Oil immersed mounting pump.

4. Bi-directional rotation of shaft with extension shaft for through drive available.

 

TECHNICAL DATA

General:-

Ambient temperature	Up to 50 C
Fluid temperature	Up to 80 C
Mounting	Face mounting
Nominal delivery Speed	300 to 1450 rpm
Direction of rotation	can be run in either direction
Weight of pump	10.5 kg to 22 kg
Connection suction side	sucks oil directly from tank no suction port in this pump
Connection "P"	3/8 BSP
Mounting bolt	M8 x 30L(4 nos.)

 

 

Hydraulic:-

 

Operating pressure	200 to 550 bar
Flow	1.5 Ipm to 27 Ipm
Fluid	Mineral Oil/Phosphate ester
Viscosity	2.8 to 300 mm2/sec.
Filteration	20 micron