We offer surgical combistim, which is an electro therapy device compact and portable light weight unit micro computer controlled LCD based programmable device. These are used to reduce the deep muscle pain and weakness, joints pain and vascular disorders etc. This is possible by low frequency, low intensity impulse stimulation, which is carried by a medium frequency, carrier consist, programmable treatment parameters.

Some of the technical specifications of our product are:

Therapy Modes	4P IFT 4P Vector 2P Modulation
Display	Program LCD Display
Intensity	99mA
IFT Medium Freq.	4 Khz
Russian current Freq.	2.5 Khz
Base Freq.	0-150 Hz
Sweep Programmed	Rectangular Wave - 1/1 Triangular Wave - 2/2 Trapezoidal Wave- 6/6
Muscle Stimulator	Galvanic, Interrupted Galvanic, Faradic, Surge Faradic Adjustable50 to 100 Hz
TENS	1Hz to 250Hz (in13 Freq. Modes)

The standard accessories offered with our range includes:

Output Cable with Jack pin	2 Pairs
Silicone Conductive rubber pads	2 Pairs
Main Line Cord	2 Pairs
Cover	1 No.
Jelly bottle	1 No.
Belts (Small & Lumber)	2 pair
Output Cable with Jack pin	2 Pairs
Spare fuse	10 paces

We manufacture continuous passive motion system(CPM), which is an electro mechanical device, fully programmable with LCD display, lower limb flexion mobilization unit. These are noiseless high torque gear motor with seat conveyer for excellent flexion angle setting. Our range can be used for septic arthritis, ligament tendon healing and for the treatment of intra-artricular fractures etc. Further, our product have a provision for treatment time, setting of flexion angle and extension provision, hold on flexion and hold on extension cyclic time. Moreover, our range can also be used for improvement of blood circulation, reduction of venous engorgement of deep venous thrombosis, extra and intra adhesions, joint stiffness and pain reduction etc.

Some of our features of our products are:

• User friendly operation of unit.
• Fully programmable with LCD display and key pad.
• Jerk free and noiseless high torque gear motor with speed control.
• Easy leg holding hollowed cushioned leather seat and straps.
• Patient remote to switch off the machine in absence of doctor.

The technical specifications of our range includes:

Input voltage	220v Ac /50Hz
Treatment time	0-99min
Power consumption	35w max.
Flexion hold time	0-9 Sec.
Extension hold time	0-9 Sec
Flexion Angle	10° -120°
Dimension	(1050x270x300) (LxWxH) mm
Weight	16.5 kgs.

We offer interferential therapy machine, which are commonly used in pre and post-orthopedic surgery, joint injury syndrome, cumulative trauma disorders, increasing circulation and pain control of various origins. Further, this therapy is also used in the treatment of circulatory disorders, range of motion, edema and muscle spasms.

Some of the technical specifications of our product are:

Operating Voltage	230 volts AC supply 50 Hz, 5 AC current
Output type	100% Isolated
Medium frequency	4 KHz & 2 Khz
Output	Two separate outputs CH-1 & CH-2
Output Current	0 to 50 MA
Output frequency	It can be varied by intensity control. CH-1 – 4000 Hz - 3850Hz depending on the beat freq. on selection of scan. CH-2 - 4000 Hz[constant]
Display	Interference frequency indicator by 3 digit Digital Seven Seg.Display
Timer	0 – 99 minutes can be varied
Scan patterns	Rectangular, Trapezoidal, Triangular
Therapy modes	4 Pole interferential therapy, 4 pole vector interferentialtherapy, 2 pole interferential therapy.

We offer advance laser therapy unit with pen, which are widely used in hospitals, medicals and clinics.

Some of the technical specifications of our range includes:

Laser Beam Class	3B
Mode	Continuous & pulse mode.
Maximum Probe Power	20 mw
Beam Surface	0,025 cm2
Laser type	Semiconductor GaAs
Wave length	850 nm
Power density	0.8 w/cm2
Laser Beam Class	3B
Max energy within 1 min	1.2 joules

Our range of Ss2s is a compact solid state microprocessor controlled unit with digital timer & intensity display. These are useful for functional paralysis resulting for traumatic neurosis, hysterical, facial paralysis, cardiac vascular disorder, muscle strain and others. Further, our range comes in a compact ABS molded cabinet.

Some of the technical specifications of our range includes:
 

Pulse Duration	03,1,10,30,100 & 300 m-seconds
Pulse repetitive Frequency	0.3,1,3 seconds
Intensity	Variable form 0 to 130 volts
Power supply	190 to 260 volts , 50 hz
Working Modes	Galvanic, I. Galvanic, Faradic, S. Faradic

The standard accessories with our products are:

Main cord	1 pc
Pad electrodes	2 pairs
Electrode wires	2 pairs
Jelly bottle	1 pc
Belt (small)	2 pc
Belts (large)	2 pc
Carry case	1 pc

We manufacture surgical daithermy 250 watts, which is a high-frequency surgical unit for cutting and coagulation. These have a built in alarm system for malfunction of the unit. Further, our range have an independent output and controls for all the mode like cutting and coagulation. In addition, our product have a built in audio and visual alarms and indication for all the features.

Some of the technical specifications of our products are:

Cutting output	250 watts
Coagulation output	150 watts
Bipolar output	75 watts
Cutting output (blend)	200 watts
Coagulation output (blend)	100 watts
Bipolar output (blend)	75 watts
Voltage required	220 volts

The standard accessories with our range includes:

Main cord	1pc
Bipolar forceps with cable	1pc
Unipolar handle with cable	1pc
Patinet cable and plate	1pc
Spare fuse	1pc
Electrode set	1pc
Foot switch	1pc
Hand switch	1pc

We have specially designed SWD 250 keeping in view the various needs of the profession for induction heating of the tissues using condenser pads. Being a portable unit, it can be used by the beside in Hospitals & Nursing Homes & can easily be taken to patient’s home by Orthopedic surgeons & Physiotherapists. This simple to use & highly efficient unit utilizes high frequency mode in five stage to maximum of 250 Watts. The resonance can be controlled by a tunning knob. The treatment time is set by a built in Timer which also work as on – off switch. The unit is automatically switched off after the completion of dosage time. The unit is housed in a sturdy & attractive cabinet.

Technical Specifications:

Power Output	250 watts
Operating Frequency	27.12 MHz .
Wave Length	11 Metres.
Main Supply	220-240 volts 50 cycles
Fuse	5 Amp .
H.F. Power Source	Vaccum Generating Valve

Standard Accessories:

Main cord	1 pc
Pad electrode	1 pair
Electrode wire	1 pair
Machine cover	1 pc
Spare fuse	10 pcs

Our SWD 500 is specially designed for hospital and large physiotherapy centers where the machine is required to fun constantly for many hours to cope with the rush of patients. The unit is user-friendly and can be continuously used for many hours due to its heavy components. Following are some essential aspects of our product:

Sailent Features:

• Mechanical Timer Switch 0 to 30 minutes.
• Intensity Control in 5 steps forms 0 to 500 watts
• Endless tuning system
• Voltage filament control to provide safety to the Vacuum tube
• Cooling fan to keep the Vacuum tube cool.

 Technical Details:

Power output	500 watts (approx)
Operating frequency	27.12 MHz
Wave length	11 meters
Main supply	220 volts 50 cycles
Fuse	5 Amp
H.F power source	Vacuum Generating Valve

Standard Accessories:

Main cord	1 pc
Pad electrode	1 pair
Electrode wire	1 pair
Machine cover	1 pc
Spare fuse	10 pcs
Instruction manual	1 pc

Our SS 75 muscle stimulator is compact solid state Microprocessor controlled unit with digital timer & intensity display. Fun function display is useful for functional paralysis resulting for traumatic neurosis, hysterical, facial paralysis, cardiac vascular disorder, muscle strain and others. This therapeutic stimulator for Galvanic, Interrupted Galvanic, Faradic and surge Faradic Currents. The unit comes in a compact ABS molded cabinet.

Technical Specifications:

Pulse Duration	03,1,10,30,100 & 300 m-seconds
Pulse repetitive Frequency	0.3,1,3 seconds
Intensity Variable form	0 to 130 volts
Power supply	190 to 260 volts , 50 hz
Working Modes	Galvanic, I. Galvanic, Faradic, S. Faradic

Standard Accessories :

Main cord	1 pc
Pad electrodes	2 pairs
Electrode wires	2 pairs
Jelly bottle	1 pc
Belt (small)	2 pc
Belts (large)	2 pc
Carry case	1 pc

We offer transcutaneous electrical nerve stimulator (TNS), which help to generate electrical impulses that are sent through electrodes placed over nerve centers. These are safe, non-invasive, drug free and has no side effects. Our range gives relief to the patients with the continuous mild electrical activity, which blocks the pain signal traveling to the brain. Further, our range is microprocessor controlled.

The technical specifications of our product include:

Output Channels	4
Frequency	2, 40, 80, 130 kHz
Timer	0 to 99 minutes
Treatment Programmer Burst	7 sec on, 7 sec off.
Sweep	It generates impulses
Frequency	2~40~80-130 Hz
Pwm	It generates impulses of variable
Pulse width	Variable intensity 150 to 250 micro sec.
Wave Shape	Monophonic
Main Supply	230 volts A.C

With our range, we offer the following standard accessories:

Patient cable with pad	4 pairs
Belts	4 pc
Main cord	1 pc
Machine cover	1 pc
Patient cable with pad	4 pairs
Jelly bottle	1 pc

We are a trusted name in manufacturing of Traction machine, which delivers peak performance and are available at cost effective prices.

Following are some of the features of our product:

• User-friendly
• Long lasting service
• Minimum maintenance

Our range of ultrasonic machines are designed and developed with fully solid state microprocessor controlled unit, with digital timer & intensity display and is very lightweight compact and portable. Further, in our range, we have incorporated with sound head with a special transducer is designed to keep a very good skin contact for deep ultrasound therapy. Our products are widely used in neuromuscular and muscular-skeletal diseases including arthritis, sinusitis etc. The sound head generator in our range minimizes heat and helps to eliminate any discomfort of the patient. Moreover, our range operates on 220/240 volts A/C.

The technical specifications of our range includes:
 

Operating Modes	Continuous & pulse mode
Pulse Mode Ratio	1:1, 1:4, 1:7, 1:10
Operating Frequency	1 Mhz
Output	15 Watts Max Continuous Mode 21 Watts Max Pulse Mode
Ultrasonic Power Density	Up to 3 Watts / Sq Cm
Treatment Time	0 To 60 Minutes
Power Supply	210 To 260 Volts

Further, the standard accessories with our range includes:

Ultrasonic applicator	1 pc
Jelly Bottle	1 bottle
Ultrasonic applicator	1 pc
Main Cord	1 pc
Unit cover	1 pc
Instruction manual	1 pc