Shalimax decorative waterproof cement paint is an exterior coating made in powder form with Portland Cement as its base. We offer clients a wide range of waterproof cement paint solutions for meeting the exterior waterproofing demands. 

Advantages

• Provides a durable, hard & waterproof surface
• Does not rub, flak or peel off when applied as per instruction
• Hygienic and resistant to climatic changes
• Easy to use
• Excellent heat and light reflector
• Ideal coating for exteriors of houses, factories etc
• Available in myriad shades

Note : Darker shades are liable to fade / fleet once recommended for interiors.

Surface Preparation

Care has to be taken & seen that all surfaces are free from dirt, dust lichen, algae, etc. Loose material and dirt needs to be removed by brushing and where necessary by washing. All surfaces in hot climatic has to be saturated with clean water & moisture needs to be allowed partially to dry off the surface before applying the first coat.

Mixing Instruction

Mix the content of the pack by shaking it before opening for the first time. Easily crushable limps if found, are to be crushed and then used. Mixing with water is to be done in two stages.

First Stage
Take 1 measure of the paint. To it and ½ measure of water and mix well, so as to achieve a smooth creamy paste like consistency.

Second Stage
Allow the paste to remain in the same consistency for a short period of time & then, again add ½ measure of water slowly, stirring well. Now the cement paint is ready for use.

Packing
Bags are available in 25kg and 5kg.

The plastic emulsion paint offered is a new type of surface coating for interiors of cement asbestos cement and hard board buildings. It dries quickly to a smooth durable finish with no brush marks and patches. It is best suitable for colour conditioning in construction of houses.

Paint surface can be washed with soap and water periodically for maintaining the look. The paint has an excellent alkali resisting property and adheres tightly to cement mortar or plaster surfaces. It hardly changes in colour and is ideal decorative coating in a light room.

Application

Depending on porosity of surface the paint can be thinned with water and applied by brush. Two coats of paint delivers good results.

Surface preparation

Surface needs to be sand prepared for making it free of grease etc., and also ensure to make it free of moisture. To prevent patches, checking efflorescence coat of plastic primer is advisable.

Application

Wet the surface well, allowing the water to run down. Then apply our plastic emulsion paint with a brush of good density & smooth bristles. The first coat has to be so brushed into the surface so that a good bond is formed. The second or subsequent coats can be brushed or sprayed.

Curing

The surface on which this emulsion paint is applied should be wetted at the end of the day with a fine water spray. There has to be an interval of 6-8 hours for wetting after the application of paint.

Recommended Method of Curing

After the first coat of this emulsion paint, curing is recommended in upward direction especially when dark shades are applied, so as to avoid any watermarks. 

Note : Dark shades generally require more curing than light shades.

This acrylic washable distemper is a preferred choice of billions of household users. Known for unmatched durability and good wash-ability, this acrylic washable distemper comes at a very reasonable price. The distemper is available in a vast array of shades that are completely devoid of dirt & microbes thus delivering unmatched clean and bright look. Based on time tested Acrylic co-polymer emulsion the distemper is offered in snow white and variety of unique range of pastel shades.

Surface Preparation:

• In case of previously painted surfaces ensure to remove all loose & flaking particles properly
• Then scraped off all previous coating of lime wash, colour wash or powder distemper
• Make the surface clean and dry for good effective.

 Application:

• Use a coat of cement primer (water or solvent thin-able)
• Add water slowly to the distemper paste mixing the contents thoroughly & thinning it for application consistency ( 2 parts of water should be added 3 parts of shalimax)
• On surface primer as above apply 2 to 3 coats by a brush roller or spray
• Keep 6-8 hours interval between coats.

 
Covering Capacity

Approximately 4 to 6 sq. meter per kg.

Packing Available in:

1 Kg. Packet
5 Kgs. Bucket
10 Kgs. Bucket
20 Kgs. Bucket 

We offer a wide range of dry distemper. The suited economical treatment of interior walls and ceilings this dry distemper imparts solid decorative finish various interiors.

Mixing Instruction

Add to moderate hot water, gradually by stirring constantly until a stiff paste is formed. Allow the pate to stand for 30 minutes and then thin it to the required consistency by adding water.

Surface Preparation

The surface has to be sand papered down and defects like cracks holes etc. should be filled with plaster & smoothened. Let the surface dry off before the surface is washed clean & free from dust and grease.

Application

The distemper is applied evenly with a good brush. Ensure to stir the distemper from time to time during application. For very absorbent surface a coat of glue size is recommended.

Drying Time: Approximately 6 hr.

Packing: Available in 1.5 Kgs. & 20 Kgs.

Covering Capacity: 9 to 12 sq. meters per Kg. depending on surface.

This cement colour takes the drabs out of plain grey and white cement and transforms dull concrete into fascinating coating. Fast to light and alkalies, the colours it delivers are widely used by tile and distemper manufacturers and situ workers.

Beauty in Colour

These cement colors are available in 17 attractive shades for limitless use. Used for making paving stones, coloured renderings on buildings, concrete bricks and composition flooring. It is also available with colours that used for camouflage by defense.

Application

Mix thoroughly with dry cement and pass it through a fine sieve. Then add water and aggregates in proportion according to intensity of colour needed. For example if you need pastel shades, 5 kg. of per bag of cement is recommended.

Packing Available in:

1Kg Pouch
5 Kg. Bag.
25 Kg. Bag.
50 Kg. Bag.

We offers integral waterproofing compound. During the preparation of concrete right composition small capillary pores are formed in the process of adding water to achieve the required workability and compactness. Due to these pores, this concrete is permeable to water and it contains chemicals that cause contraction of the capillaries thus converting the water absorbing capillary forces to water repellent forces.

Advantages:

• Increases Workability of the concrete mix.
• Reduces capillary action.
• Reduces vapour transmissions through walls and slabs
• Non-toxic
• Does not corrode the reinforcement due to Chloride free contents.
•  Makes concrete watertight.

Typical Applications :

• Used in mass concrete.
• Foundations walls.
• Floors.

Most suitable powder polymer based tile adhesive / fixture with good fixing and water proofing capacity. This tile adhesive is suggested for fixing tiles tightly & for the long run.

We offer sand textured wall finishes, made up of touch flexible resin and specially selected aggregates. They provide everlasting texture, a decorative finish and also protection against extreme climatic variations. These sand textured wall finishes are highly reliable, durable and weather resistance exterior coatings.

Application : One coat of Primer or Cement Paint and two Coat of wall finish

Covering Capacity:

 Approximately 60 to 70 sq. ft. per 1 Kg. per coat.

Packing Available in packs of:

5 Kg.
10 kg.
20 kg.
30 Kg.

This exterior emulsion is specially formulated coating for protection of exteriors from polluted climate & rough weather conditions. It is a 100% Acrylic Resin with selected grades of additives, pigments and chemicals that ensure best possible protection. This exterior emulsion does not pick dust or fades & peels off thus preventing the structure from fungus / algae growth.

Covering Capacity : Approximately 80 to 110 sq. ft. per litre. Per coat

Packing
Available in
1 Litre Box.
4 Litre Buckets.
10 Litre Buckets.
20 Litre Buckets.

We offer white cement based wall putty with extraordinary adhesion strength that is manufactured by us. These are suitable for cement-plastered walls and ceilings and are also used to fill the uneven surfaces of cement-plastered walls and concrete walls. Putty manufactured by us assures smooth and strong finish to the surfaces for further application of paints. The smooth finishes deliver better look & enhances the colour effect of the applied paint.

We offer high quality specialty industrial use minerals like hydrated lime, dolomite powder, soap stone powder, graphite powder, bentonite powder, chalk mitti, china clay, POP and Quick Lime.

These industrial moinerals are available in variety of custom packed options depending on bulk buyer