Telecom Equipment Rental / Services

The jdsu fst-2802 is a handheld ethernet, fibre channel, and ip services test instrument designed to meet the needs of service providers for turning up and troubleshooting these various services. The jdsu fst-2802 enables technicians to use one test set to turn up services ranging from 10/100 ethernet, gigabit ethernet, fibre channel, and ip – all from a single testpad module

 

Features:

• Full line rate traffic generation with variable traffic load characteristics to stress test A0/100/1000 mbps ethernet interfaces.
• Ability to test 1. 0625 and 2. 125 gbps fibre channel services at 100% wire speed.
• Ip ping and traceroute testing for verification of network connectivity.
• Ability to perform ip throughput verification and round trip delay testing.
• Filtering capabilities at l2 and l3 enable users to perform circuit troubleshooting.
• Dual-port capability for ethernet and fibre channel traffic generation.
• Ber testing at layer 1 and layer 2 for ethernet and fibre channel circuits.
• Loopback frame generation to automatically loop the far-end test at l2 and l3.
• Remote graphical user interface (gui) application for remote testing via an analog modem, ethernet lan, 802. 11, or bluetooth.

 

The jdsu fst-2802 is a handheld ethernet, fibre channel, and ip services test instrument designed to meet the needs of service providers for turning up and troubleshooting these various services. The jdsu fst-2802 enables technicians to use one test set to turn up services ranging from 10/100 ethernet, gigabit ethernet, fibre channel, and ip – all from a single testpad module!

 

Features:

• Full line rate traffic generation with variable traffic load characteristics to stress test 10/100/1000 mbps ethernet interfaces.
• Ability to test 1. 0625 and 2. 125 gbps fibre channel services at 100% wire speed.
• Ip ping and traceroute testing for verification of network connectivity.
• Ability to perform ip throughput verification and round trip delay testing.
• Filtering capabilities at l2 and l3 enable users to perform circuit troubleshooting.
• Dual-port capability for ethernet and fibre channel traffic generation.
• Ber testing at layer 1 and layer 2 for ethernet and fibre channel circuits.
• Loopback frame generation to automatically loop the far-end test at l2 and l3.
• Remote graphical user interface (gui) application for remote testing via an analog modem, ethernet lan, 802. 11, or bluetooth.

 

We offer network sync audit-

The aim of this network synchronization audit (sync audit) is the quality verification of the network clock distributed by SDH as well as 2 Mbit/s PCM lines within the Customer network.

But due to the limited time frame to perform long term measurements the results can only deliver a snapshot of the current situation for parts of the network. Basically this reflects the performance of the whole network.

Generally two measurements were made, a short term measurement to evaluate jitter and a long term measurement to evaluate wander. The gathered datas were then compared to the network requirements as specified by ITU-T.

 

The ITU-T requirements for traffic lines used for Network synchronization

(Sync Audit) are specified in terms of MTIE and TDEV with limits set over a range of values.

These  limits are represented by a mask which the measurement results should not exceed. Primary reference timing signals are required by ITU-T to meet a frequency accuracy of 1 x 10-11. All synchronization signals should be traceable to PRC’s which must meet this frequency accuracy.

SDH analyzer(ant 20 se)—easy to use compact test kit  for sdh bit rates upto stm-64 including jitter &  wander testing platform offerings sdh,atm,pdh capabilities. testing of bert, errors, alarms, performance & pointer analysis, and clock synchronization testing.

We are offering network analyzer.

 

Network analyzer( hp 8751 a) – provides capability to measure refletion & transmission characteristics like return loss  of two port device in either direction with a single connection. Frequency range is 5 hz to 500 mhz. Measures transfer functions, insertion loss/gain, attenuation gain compession, s-parameters, electrical ength, group delay, deviation from linear phase, impedence- magnitude phase; return loss, full accuracy enhancement.

Offering EMF Testing.

We offer broadband & frequency selective measurements by spectrum analyzer for rapid, high-precision, cost-effective signal investigations. It provides a large number of measurement functions and of a mobile radio base station for development and service an extensive range of applications. precise measurements a frequency-selective receiver with high sensitivity, a large dynamic range and precise measurements of the field strength is required. for accurate and reproducible measurement results.

- Broadband power meter
- Super fast real time display
- Very easy to use
- Shows puls/ modulation frequency
- Peak, peak hold and average (AVG)
- Direct display in dBm and dB V (switchable)
- Full 70dB dynamics without switching
- High-performance DSP (Digital Signal Processor)
- High resolution multi-function display
- AM demodulation (audio function)
- Frequency range: 100 Khz to 6 GHz
- Typ. level range: -70dBm to 0dBm
- Typ. precision base unit: +/-3dB.

 

We offer agilent & narda spectrum analyzer with 3D Isotropic  antenna.
Providing sheets as per TEC Formats.

High-precision, cost-effective signal investigations. It provides a large number of measurement functions and of a mobile radio base station for development and service – an extensive range of applications. precise measurements a frequency-selective receiver with high sensitivity, a large dynamic range and precise measurements of the field strength is required. for accurate and reproducible measurement results.

 

• Broadband & Frequency selective measures.
• Superfast REALTIME display
• Shows puls/modulation frequency!
• PEAK, PEAK Hold and average (AVG)
• Direct display in v/m and w/sqM (switchable)
• Full 70dB dynamics WITHOUT switching
• High-performance DSP (Digital Signal Processor)
• High resolution multi-function display
• AM demodulation (audio function)
• Frequency range: 100KHz to 6GHz
• Typ. level range: -70dBm to 0dBm
• Typ. precision base unit: +/-3dB

THE Power Meter and RF Meter for the novice with high sensitivity and easy operation.

This unit provides a quick overview of various signal sources and even shows the modulation and puls-frequency! Large, very responsive FSTN digial display incl. bargraph for perfect visualization of results. Integrated speaker and audio output with volume control. Battery powered.

We are offering site master (vswr meter).

Site mater (bird & anritsu)   

Offers fault location or dtf mode indicates vswr or return loss levels at each point along the cable and antenna system length

 

Cable loss function measures insertion loss of the cable system over a given frequency range site analyzer® is the user-friendly test solution for installing, maintaining, and troubleshooting your antenna and cable systems. Field engineers and technicians rely on this rugged handheld tool to get the job done. Wireless equipment manufacturers, service providers, contractors, tower erectors and military field personnel worldwide approve of the analyzer’s precision vswr and return loss results. this versatile product also includes a digital power meter option to accurately measure the output power of your base station. Wideband power sensors are available from bird up to 4 ghz for use with this option.

We are offering E1 Tester.

Ber Meter (EDT-135) is a multipurpose field service tester designed for commissioning, maintenance, and troubleshooting on E1 PCM circuits. They can perform a wide variety of tests, including: framed and unframed monitoring, framed and unframed end-to-end testing, drop and insert, channel associated signaling monitoring, Round Trip Delay measurement and repeated BERT. The EDT-130 and EDT-135 have a similar range of features for E1 circuit testing, plus an extended range of interfaces for data circuit and primary multiplexer testing.

We are offering e1_data tester.

ber meter (edt-135) is a multipurpose field service tester designed for commissioning, maintenance, and troubleshooting on e1 pcm circuits. They can perform a wide variety of tests, including: framed and unframed monitoring, framed and unframed end-to-end testing, drop and insert, channel associated signaling monitoring, round trip delay measurement and repeated bert. The edt-130 and edt-135 have a similar range of features for e1 circuit testing, plus an extended range of interfaces for data circuit and primary multiplexer testing.

 

We are offering OPM.

Optical power meter can meet general test requirements of fiber identification, attenuation/loss measurements, continuity verification and transmission quality evaluation on singlemode and multimode fibers in LAN/WAN/CATV infrastructure. OPM is ideal for both lab and field applications offering high quality, high stability and competitive low costs.

Offers network optical power management applications at different wavelengths

ie. 850nm, 1300nm,1310nm,1490,1550nm etc.

 

CONTACT: Mr. Devendra 9827056888

               Mr. Akhilesh 9826950088

 

We are offering OVA.

Easy-to-use variable attenuator for reducing the power

level of an optical signal.

Idea tool for field work, with features of compact size, stable performance

and shock proof design.

Used for single mode fiber together with laser source and power meter.

Provides  variable attenuation at 1310/1490/1550nm wavelengths, for the measurements of test instruments and communications equipments.

Offering Sync Audit Services.

Summary of Service Provided

Audit is performed by Techno Fibre Industries Services field engineer using precision timing

instruments and sophisticated audit software to make measurements and assess network synchronization

performance.

The Techno fibre engineer will work with your design or network management team to determine appropriate

sites for taking measurements and data gathering.

Measurements include:

                · Jitter

            · Short-Term Accuracy

            · Long-Term Accuracy

            · Time Interval Error (TIE) / Phase Deviation

             ·  Maximum Time Interval Error (MTIE) – short-term and long-term wander

            · Time Deviation (TDEV) – short-term and long-term wander

· All measurements adhere to ITU-T, ETSI, Telcordia and ANSI requirements. T1, E1 or

    SONET/SDH signals from your live network are plotted against current ITU-T, ETSI, or ANSI

     masks

· Measurements can be used to determine compliance with national or international standards and

    to locate the source of system anomalies and to determine the effectiveness of your current

    synchronization equipment

· Analysis of the network is conducted without disrupting current services

· Confidentiality is maintained. Measurement data will not be disclosed to any third party without

                 The prior written consent of the customer

Deliverables

· Complete set of graphs showing individual measurements and cumulative results

 

Offering rubidium timing reference source.

The rubi source 2000 is a powerful reference source, used to enable fast measurement and testing of the synchronization quality of PDH/ SDH/ SONET digital networks. MTIE and TDEV measurements for up to 1000 seconds can be easily performed without a GPS reference. Coupled with a GPS antenna, the range of observation time can be  largely extended to meet specific requirements.

 METROLOGY:- Standard 5 MHz and 10 MHz reference sources are also provided for metrology and calibration laboratory equipment such as universal counters, spectrum analyzers and synthesized signal generators.