We offer rotary aluminum melting furnaces, which are designed for fuel efficient. These are of different capacity. Further, our products are duly lined with refractory lining in combination with castable of different grades to achieve the maximum efficiency of the furnace and also to reduce the skin temperature of the furnace.

Some of the advantages of our products are-

• Reduction in electricity consumption of more than 90%
• Reduction in oil consumption about 30%
• Reduction in initial / subsequent heating time
• Auto control on/off or modulating type.

Our range of oil, gas fired bale out furnace are made of qualitative raw materials. These are duly lined with ceramic fiber lining along with highly efficient monoblock type burner. Some of the advantages of these products are as follows.

• Reduction in electricity consumption of more than 90%
• Reduction in oil consumption of about 30%
• Reduction in initial /subsequent heating time.
• Auto control on/off or modulating type
• Accuracy in temperature control by digital controller

Our superior quality and energy-efficient Film Burner comes with the following features and benefits:

• Billet heating furnaces for forging industry
• Billet heating furnaces for rolling mills - ferrous and non - ferrous
• Heat treatment furnaces such as salt bath, normalizing and annealing furnaces
• Galvanizing furnaces.
• Ceramic and glass furnaces
• Drying ovens.


• Ladle heating furnaces for mini steel plants.

Our products are incorporate with the following features.

• 15% or more reduction in fuel oil consumption


• Higher turn down radio of 7: 1


• Operates at low percentage of excess air, which is less than 10%


• Reduces sulphur corrosion due to lesser formation of sulphur tri-oxide


• Can handle heavier viscosity grades of fuel oil as compared to convectional burners.


• Less sensitive to variations in oil pre-heating temperature and saves energy


• The flame stabilizes within seconds of start up due to improved atomization.


• Can handle pre-heated combustion air up to 250 C without associated problems of oil cracking, thereby preventing choking of burner nozzles.


• Reduces heating time, leading to higher productivity


• Eliminates the problem of fuel oil dripping.


• Convenient to maintain because it is easy to clean and can be refitted immediately. So, reduces the maintenance and shut down time.


• Requires less maintenance time as compared to convectional burner


• Choking in the burner block and oil passage totally eliminated


• Existing burners can be easily replaced, without the need of replacing accessories such as the air blower, burner block, etc.

We offer fuel oil pumping & heating units, which are made of qualitative components, pre-engineered and are properly packed. These are custom design to meet the requirement of our customers. Further, our products are applicable to deliver heavy viscosity fuel oils to furnaces, kilns, oven, dryers, boilers etc at a pressure of 15-20 psi and at a temperature of 90-100°C and near burner tip. Apart from this, our
fuel oil handling system minimizes start up and operating difficulties and also reduce maintenance costs. These are available in the models such as-

• Simplex (single gear pump with motor & single heater)
• Duplex - I (two gear pump with motor in parallel & single heater)
• Duplex - II (two gear pumps with motor and two sets of electric heaters, all in parallel.

Features of our products

• Pre-engineering to meet the specific clients requirements
• Skid mounted and pre-pied
• Easy field installations
• Built in thermostat for automatic control of oil temperature

We manufacture centrifugal steel plate air blower, which are designed to give maximum CFM volume & pressure of air with low power consumption. These are applicable to supply air to combustion systems and in low pressure air. Further, our products are equipped with TEFC, squirrel cage, induction motors like NGEF, ABB, Crompton etc. Apart from this, these products have options of direct drive / shaft driven through 'V' belts.

Features of our product

• Rigid construction.
• Statically and dynamically balanced.
• Field adjustable discharge position.
• Capacity range from 3 HP to 60 HP.
• Pressure 6'' w.g. to 44'' w.g.

We offer waste incenerator, which help in protecting the environment from hazardous wastes. These are installed and designed as per the clients requirement.

Some of the features of our product are:

• Complete combustion and smoke free & very low emissions of carbon monoxide
• Dual chamber design, which help to minimize emission of particulate matter and to provide sufficient oxygen, turbulence, high temperature and residence time in secondary chamber for complete combustion
• Simple & effective pollution control : Quenching and scrubbing in one unit, no plugging ,compliance with strict air emission standards
• Venturi scrubber to quench the hot flue gas and to remove particulate matter and acid gases. Our product is a simple system without clogging or plugging potential and designed for the removal of liquid droplets in the outlet gas
• Versatility : Auto allows incineration of all type of waste at maximum capacity and minimum use of auxiliary fuel
• Automation : A simple control system based on first principles of combustion has been designed and tested which prevents 'black smoke' generation
• Energy recovery : Optional hot water generation with the help of a condensing heat exchanger, which is used to recover energy in the form of hot water
• Cost effective : Simple design operation and maintenance
• Fine polishing emission control (Optional) : Helpful in meeting standard for particulate matter and acid gases and also trace organic compounds and other pollutants. This is incorporated with activated carbon and HEPA filters

Our products range include:

• Bio medical waste incineration system, ranging from 20kg./hr.t to 500 kg./hr.& above
• Industrial waste incineration system, ranging from 20kg./hr. to 1000 kg./hr. & above

We can provided the electrically Heated furnace as per your size and capacity for the Heat Treatment process, Non Ferrous Melting Furnace. upto 1600 Deg. C. The Furnace will be lined with 115 mm High alumina Element Holding Bricks backed by Hot face Insulation further backed up by Milk Board to achieve the minimum skin temperature and reduce radiation losses.

We can also offer Hot Air Generator Direct/IndirectType of different capacity suitable for oil and Gas. The capacity of Hot Air Generator start from 25, 000 K cal/Hr. to 10,00,000 Kcal/Hr. These type of Hot Air Generator Generally used in for Drying Process, Rice Mills Dryer, Wood Drying Process and other related drying process. We can also design electrically heated Hot Air Generator as per your requirement.

Our range of ring main system are made of superior grade raw material, which ensures the durability and reliability of our range. These are oil circulation system for furnace oil. Furthermore, we offer our products at industry leading price.

We provide Paint Soaking Oven for soaking the Liquid paint and Powder also. These oven can be Electrically Heated, Gas Fired and Oil Fired as per the requirement. These Oven can be Batch Type and Conveyor type for continous production.