Telenet has a wide range of well-designed high-speed and high performance ADSL2+ /VDSL router, supports kinds of network protocols, steady runs preferred by the individual users, the SOHO, and the small enterprise to access the internet. High performance gateway.
 
Our ADSL2+ /VDSL routers is available in different configuration:

ADSL2+ CPE

• Adsl2+ Combo Router 1(With 1 Ethernet &USB) TNDSL 2120
• Four Ethernet Adsl2+ Router TNDSL 2140
• Ethernet Wireless ADSL2+ router TNDSL 2220
• Four Ethernet Wireless ADSL2+ router TNDSL 2240
• ADSL2+ Integrated Access Device/Router (2 Ethernet, 1USB) TSIAD 22120
• 4 Port ADSL2+ Integrated Access Device (4 Ethernet, 1USB, 2 FXS, Windows) TSIAD 22420

 VDSL2 CPE

• VDSL2 Integrated Access Device TSIAD 42420
  

Features:

• Bridging & Routing
• Support SNMP & TR 069 (optional)
• Maximum Transmission range up to 6 Km
• 8 permanent virtual circuit
• NATing
• IP Filtering
• Port Mapping/Forwarding
• DHCP
• IGMP Snooping
• Compatible with all VPN
• QoS Support
• Firmware Upgradable
• 800 DMIPS MIPS32 processor core
• 32 MB DDR SDRAM running at 133MHz main clock(DDR266)
• 8 MB Flash memory
• ADSL2+ ANNEX A interface complied with G.994,G.992.1,G.992.2,
• G.992.3 (ADSL2 ), G.992.5, ANSI T1.413.
• Hardware ATM segmentation & reassembly engine with CBR, VBR,UBR and MCR shaping4X 10/100BASE-T/TX Ethernet Switch PORT
• IEEE802.11 b/g compatible Wireless Access Point
  

Telenet has a range of broadband router, adding considerable power and flexibility to the network. This broadband router assures continuous connectivity to the network resource and the internet. This high tech equipment allows sharing of broadband access with all the networked computers wirelessly or with Ethernet cables. Enables easy downloading of large files, videoconference, and distribute& play high-quality digital movies, photos, and MP3s with in frictions of seconds.

Our broadband router are available in configuration

• 4 Ethernet ports & Wifi. Model: TNDSL 4000 Series.
  

Wireless  Features:

• Compliant with Network Standard IEEE 802.11g
• Frequency Range : ISM band , 2.4GHz - 2.4835GHz
• Modulation : OFDM (Orthogonal Frequency Division Multiplexing)
• Support Dynamic data rate : 6, 9, 11, 12,18, 24, 36, 48, and 54Mbps
• Security : WEP 64/128, WPA ,TKIP , WPA2 , 802.1x, 802.11i .
• Protocol: CSMA/CA
• Support QOS Quality of Service – 802.11e , WMM (Wireless Multimedia)
• Cisco CCX V1.0 V2.0 V3.0 Compliance
• RF Transceivers :
• Tx Output Power 6dBm
• Rx Receiver Sensitivity(54Mbps) : -73dBm
• Up to 5dBm Driver Output for External PA
• 90 dBm Rx Gain & 16 dBm Tx Gain
  

Networking Features:

• DHCP server/client
• Enhanced NAT/NAPT for high throughput data service
• Packet filtering and firewall
• IP static routing
• DMZ and virtual server
• Support DNS and DDNS
• Support PPP and PPPoE
• NTP client
• 802.1d bridge
• Up to 1k MAC Learning Address
• VPN pass through
• Protocols: IP, TCP, UDP, DHCP, ICMP, ARP, DNS, DDNS, PPP, PPPoE,
• NTP
• RIP v1/v2
• UPnP

Telenet’s midspan POE is a power over ethernet (PoE) power supply with integral DC Injector. It provides DC power for one power over ethernet equipped device by "Injecting" DC power through the CAT5 (10/100Mbps) Ethernet cable on the data pair itself. Since our power over ethernet device is completely self-contained, a separate power supply and injector is not required
 
Electrical Specifications

• Ethernet Connectors RJ45 Jacks (2)
• Ethernet Data Rate 10/100Mbps Ethernet
• Ethernet Devices that can be powered Single Pair 1: Pins1/2
• Data Lines Pair 2 : Pins 3/6 VDC: Pins ½ or Pins 4/5
• Cat-5 Power (PoE) Pinout –VDC: Pins 3/6 or Pins 7/8
• Operating Temperature 0° C to 70° C
• Power Supply 48VDC @15.4W
• Max Output Current 0.35A
• Input 100-250 VAC 50H~
• IEEE Compliant Single IEEE 802.3af Compliant
  

Applications For The Telenet Power Over Ethernet

• Wireless LAN Access Points and Bridges
• Wireless LAN WiFi Amplifiers and Amplified Antennas
• VoIP (Voice over Internet Protocol) Telephones
• IP Surveillance Cameras
• Bluetooth® Access Points

Telenet’s G.SHDSL modem is a high quality and good performance SHDSL device. Its design improves the transmission performance and economize resource. As the new generation product, has not only the technical advantage but also very simple installation and maintenance procedure at the same time.

Our G.SHDSL modem are available in following configuration

• 10/100Mbps Ethernet, V.35 or E1 interface, 2 wires or 4 wires Optional Model: TNDSL 5000 Series:
  
• G.703 E 1Interface with 2 Wires TNDSL 5010
  
• V.35 Interface with 2 Wires TNDSL 5020
  

Features:

• New generation SHDSL technology, maximal transmission speed 4.6Mbps.
  
• One-pair wire or two-pair wire optional.
  
• Flexible data ports. Support dual data port in one device.
  
• Can support long distance transmission.
  
• Optional Power Supply 230V AC or -48V DC.
  
• 10/100Base-T interface accordant with standard IEEE802.3 and 1Mbytes buffer inserted.
  
• MAC address list inserted and 4096 MAC address available.
  
• E1 interface accordant with standards as ITU-TG.703???G.823 and G.742.
  
• DSL speed is modifiable
  
• Easy to install and operate. Working preferences by DIP switch and software control.
  
• Using 16TC-PAM Code to reduce ISI and to improve the transmission performance.
  

Telenet’s ISDN devices network termination for basic rate access enables subscribers to use services such as high-speed transmission of data, text and video signals in digital format over an access line in addition to voice transmission. Acting as a main gate to the world of ISDN, this ISDN devices forms a link between the subscriber lines and the user interface to the network. 

Our ISDN devices are available in following configuration

• ISDN NETWORK TERMINATOR (NT-1) Model No: NTB
  
• ISDN INTELLIGENT NT(NT TA) WITH 2 Analog ports, 1 RS232, 1 USB INTP-DPS
  
• ISDN INTELLIGENT NT(NT TA) WITH 4 Analog ports, 1 USB with PBX functionality INT –DPBX4
  

Features:

• Up to 8 access sockets can be connected to the S/T interface via a 4-wire bus.
  
• Two services like telephony and Data transmission can operate simultaneously.
  
• Data rate of 144 Kbps is available to the customer at the S/T interface.
  
• It has three bus configurations, which have different coverage ranges 
  • Point to Point.
    
  • Point-to-Multipoint: Short passive Bus.
    
  • Point-to-Multipoint: Extended passive Bus.
    

• Has four operating modes depending on whether transmission is active or inactive and whether the integrated power supply is working or not.
  
• Echo cancellation at the U interface ensures that Data Signals are transmitted bi-directionally.
  
• The interface modules operate in the automatic mode.
  
• The U interface module recovers clock synchronization signal, monitor transmission errors and initiate appropriate reactions.
  
• In the event of a long-term short circuit, the power supply module is auto switched off and resumes operation automatically with only a delay of few seconds.
  
• The design is in compliance with ITU/CCITT/ANSI/ETSI and industry standard 2B1Q line code for the U interface.
  
• It is easy to install at the user’s premises and can be installed in a wall-mounted cabinet or used as a desktop version.
  
• Testing and operation configurations can be adjusted quickly by means of switches and jumpers.
  

Telenet’s WiMax CPE Series offer the flexible frequency band, in 16d & 16e MIMO/SISO solution and the lowest power consumption of WiMAX production solution, supports the interoperable security, MIMO solution for coverage expand and using OFDM technology transmit NLOS(Non Line Of Sight) environments. User can manage the WiMax CPE by Web GUI and SNMP Manager.

Our WiMax CPE are available in following standards

• 16d (802.16_2005)
• 16e (802.16_2006)
  

Available Models

• Indoor CPE
• Outdoor CPE
• USB Adaptor
• Express Card

Telenet’s protocol converter is a high performance, remote, self-learning Ethernet Bridge. Protocol converter compact size and low cost make it ideal for cost-sensitive bridging applications.

Our protocol converter are available in following configuration

• E1 to Ethernet Converter TPC 3010
• E1 to V.35 PROTOCOL Converter TPC3020
• 4E1 to Ethernet Protocol Converter TPC 3140
• 8E1 to Ethernet Protocol Converter TPC 3180
• FX Ethernet to 4 E1 Converter TPC 3140
• FX Ethernet to 4 E1 Converter TPC 3180
• TDMoIP-4E TPC 3340
• G.703 to Ethernet TPC 3410
  

Features:

• E1 channel: both framed & unframed are OK, both 75 & 120ohm are OK
• Standard: G.703, line code: HDB3
• Alarm system for E1 loss
• Support local/remote loop test
• DB25 connector for V.35, in DCE mode
• Multiple clock selection: internal clock, V.35 line clock and E1 recovery clock
• Panel instruction for easy understanding of equipment working status
• Internal power supply, 220V AC and -48V DC optional
• Standalone and module at your selection
• Realize transparent transfer Ethernet data in 1 to 8 E1 channels
• 10/100Base-FX, full/half duplex self adapt, support VLAN.
• 10/100Base-FX support SC/FC to choice and 1550nm single mode / 850 nm Multimode to choice (For Fiber Model).
• 10/100Base-FX support IEEE 802.3 standard and 802.3U fast Ethernet standard (For Fiber Model).
• E1 port support 120Ù and physical port using RJ45.
• Setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error
• Rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
• Allow 8 E1 channels up to 10ms transfer delay. When the delay over the limitation, can stop transfer automatically.
• Support Dynamic Ethernet MAC address (4096), having local address filter function.
• E1 interface compatible with ITU-T G.703, and G.823. Signaling slot not supported.
• E1 interface having internal clock resume circuit and HDB3 codec circuit.
• Support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
• supporting 1 to 8 E1 channels customized configuration, auto detect the number of E1 channels and select the available
• E1 at reset.
• Support reset remote system from local system.
• Having Ethernet monitor auto reset function.
• SNMP Management (Optional)
  

Telenet’s ethernet switches provide a new level of flexibility and easy migration between bandwidths. The ethernet switches designed with the latest technology, support non-blocking, wire speed forwarding rate and resolves the head of line blocking problem. Our ethernet switches available in Layer 2 fast Ethernet Layer 3 fast Ethernet, Layer 2 & 3 Gigabit Ethernet, Also Unmanaged Switches & Web Smart switches with configuration 8 port 16 port & 24 Port.

Our ethernet switches are available in following configuration

Managed Switches

• 8 Port L2 10/100 Fast Ethernet Standalone Switch TSW1008
• 16 Port L2 10/100 Fast Ethernet Standalone Switch with Gigabit combo Ports TSW 1026XA
• 48 Port L2 10/100 Fast Ethernet Standalone Switch with 4 Gigabit Combo Ports TSW 1052XA
• 24 Port L2 10/100 Fast Ethernet Stackable Switch with 2 Gigabit Combo Ports TSW 1026YA

Unmanaged Switches

• 8 Port 10/100 Fast Ethernet Unmanaged Switch (PVC) TSW 8008P
• 16 Port 10/100 Fast Ethernet Unmanaged Switch (19" Rack Mountable) TSW 8016
• 24 Port 10/100 Fast Ethernet Unmanaged Switch (19" Rack Mountable) TSW 8024
  

Features:

• Plug and Play installation with automatic port configuration
• Supports sixteen 10/100Mbps auto-sensing and auto-negotiation ports.
• Provides non-blocking wire speed forwarding.
• Provides 10Mbps, 100Mbps hub and 10/100-switch functionality in one unit.
• Boosts network performance.
• Easy to view 3 LED level indicators for power and status and diagnostics.
• Embedded entries of look up table and entries of CAM.
• Supports Full/half duplex support for each port.
• Flow control fully supported
• Half duplex: back pressure
• Full Duplex: IEEE 802.3X
• Supports store-and-forward switching method
• Broadcast storm control.
• Supports VLAN & TRUNK based on ports.
• Standards
• Standard: IEEE 802.3, 802.3u, 802.3x, 802.1q 802.1P (Q.O.S), Ethernet N-Way
• Negotiation.
• Protocol: CSMA/CD
• Forwarding Rate: Non blocking, 148800-packets/second wire speed forwarding
  

Voice over internet protocol IP Phone is a revolutionary IP terminal for modern enterprises and residential. With sophisticated design. Voice over internet protocol can support versatile features. High performance and outstanding capability. But most attractive point is exquisite design and unbeatable price. With a full range of interoperability tests, voice over internet protocol is extremely compatible with a variety of soft switch. However, it will be the best competitive products for the general application from home, SOHO, SME and up to enterprises. Also Voip Gateway is an inexpensive, easy-to-install and simple to use.

Our voice over internet protocol are available in following configuration

• 1 LAN, 1WAN, 2 FXS TVP 7020
• 1 LAN, 1WAN, 1 FXS, 1 Lifeline Gateway TVP 7030
  

Features:

• Most VoIP and networking protocols support
• User-friendly interface and exquisite design
• Good interoperability for IP Centrex, IPPBX and Soft switches
• Support good voice quality and storm attacking protection
• Auto-provisioning, management and security enhancement
• Rich supplementary call services and phone features
• Built in Ethernet and Router functions
  

Telenet network transceivers has a good range of factor pluggable transceiver. Incorporating a highly reliable laser and a driver circuit, this network transceivers converts data to light. Our network transceivers is extremely safe to use. An excellent medium over the fiber optic and twisted pair cables

Our network transceivers are available in following  configuration

• SFP Transceiver 1.25G 850nm Multimode 550 Mtrs TNSFP 320 MM
• SFP Transceiver 1.25G 1550nm Single Mode 2 Km TNSFP 320 SM 2
• SFP Transceiver 1.25G 1310nm Single Mode 10 Km TNSFP 320 SM 10
• SFP Transceiver 1.25G 1310nm Single Mode 40 Km TNSFP 320 SM 40
• SFP Transceiver 1.25G 1550nm Single Mode 80 Km TNSFP 320 SM 80
• SFP Transceiver 1.25G 1550nm Single Mode 120 Km TNSFP 320 SM 120
• 1.25Gb/sSFP Transceivers with DDMI-: TNSFP 330 SM10, TNSFP 330 SM40

Features

• Hot-pluggable capability
• Digital diagnostic monitoring (Optional)
• compliant with ITU –T G.957, G.958 and MSA
• MQW FP Structure or DFB Laser
• 850nm/1310nm/1550nm/VCSEL/FP/DFB
• Duplex LC or SC (BI-DI) connector
• Single 3.3V supply & LVPECL data interface
• LVTTL logic level RX LOS
• Class 1 Laser Safety Compliance with IEC 60825-1
• Excellent EMI & ESD protection
• Qualified to meet the intent of Bell core reliability practices
• Compliant with SFP MSA specification and SFF-8472
• Links of narrow intermediate or long reach with single or Multi-mode fiber

Telenet’s media converter are meant for converting signals capable of transmission on one type of cable to signals capable of transmission on another type of cable. This media converter allows connecting longer distance fiber cables between devices that are designed only for shorter distance cables. Simple and easy installation as well as operational methods enables monitoring of Operation status.


Our range of media converter are available in following configurations

Model TFC 100 & 1000 series

Fast Ethernet - Dual Fibre, Single Fibre, Multimode, Singlemode, Gigabit Ethernet

Features:

• All Converters comply with IEEE 802.3 & 802.3u Fast Ethernet Standards
  
• LED Indication for Converters
  
• Metal Case
  
• Voltage supervisor
  
• External power supply
  

Telenets power line converter provide the transmission of broadband data service via power line which are suitable for use in a wide range of both residential (in home) and commercial (offices, apartments, hotels and warehouses) network applications in which existing power line can be utilized. There is never any need to install new wires. These power line converter adapters enable the effortless creation of a high-speed network that supports video, voice and data.
 
Features:

• Universal supply works over a power line voltage range of 85 to 265 VAC, 50- 60 Hz
• Support QAM 256/64/16,DQPSK,DBPSK and ROBO modulation schemes
• Up to 85 mbps data rate on the power line
• Home plug Turbo 1.0 compatible
• Integrated Quality of Service features such as prioritized random access,contention- free access, and segment bursting.
• Low power consumption