We offer highly efficient and low maintenance Agitators in mild steel/ stainless steel grade 304 or 316 along with different types of blades for different types of uses. We offer various types of agitators such as Industrial Agitator, Anchor Type Agitator, Laboratory Agitator etc. Our agitators are provided with rigid extra heavy taper roller bearings for a better life and load taking capacity. Also, there is a provision of self lubrication and is designed for easy maintenance. These agitators are extensively used for the varied mixing needs of Chemicals, Pharmaceuticals, Adhesives, Paints, Coatings, Pigments, Foods, Dairy, Varnish Industries etc. further, sturdy construction and low energy costs have made us one of the well known Agitator Manufacturers and Exporters from India.
We offer a complete range of vertical air receivers used for storage of compressed air. Our Air Compressor Tank is highly famous and are demanded by all. We are also one of the well known Industrial Air Compressor Tank Exporters from India. Our Portable Air Compressor Tank is equipped with the following:
Volume of tanks ranges from 50 to 2000 liters. We perform quality checks on these tanks by pneumatic/hydraulic testing at pressures much higher than the operating pressures. We also manufacture in compliance with the relevant standards used for pressure vessels. Material of construction - S.S. /M.S. We also manufacture receiver tanks according to client’s specifications and demands. These tanks are provided with necessary accessories such as safety valve, drain cock and pressure gauge.
Air Preheater is basically heat transfer equipment to heat air before another process. These types of air-pre-heaters find application in papers mills, sugar mills and in power plants.
The primary objective of using an air Preheater is to increase the thermal efficiency of the process.
One of the purposes of the air pre heater is to recover the heat from the boiler/furnace flue gas, which increases the thermal efficiency of the boiler/furnace by reducing the useful heat lost in the flue gas. Fresh Air enters from topside vertically on one end & passes down through a number of tubes. It collects at the bottom in a chamber from where it again rises up vertically before exiting the Preheater. The numbers of tubes are used to increase the surface area of contact between flue gases & fresh air & to enable better & more even heat transfer.
As a consequence, the flue gases are also sent to the flue gas stack (or chimney) at a lower temperature, allowing simplified design of the ducting and the flue gas stack.
Most of the industries allow flue gases to escape at a temperature of 600-900 Deg. C allowing significant percentage of fuel between 35-50% input as wastage to the atmosphere.
Preheating of combustion air is the most commonly used method of waste heat recovery in almost all types of furnaces. Care has to be taken that the preheated air ranges between 250-500 deg. C depending on what the burners can withstand.
The L.A.P. type burners fitted on most of the furnaces have a limitation of preheated air temperature of 250 Deg. C.
We are also one of the well known manufacturers of air preheater.
Ms. Thermal Engineering Corporation offers highly efficient, sturdy and low maintenance costs Axial Flow Fan for use in ventilation and exhaust. We offer various types of axial flow fans such as Industrial Axial Flow Fan, Tube Axial Flow Fan, Marine Axial-Flow Fan etc. Our Axial flow fans are compact in nature and the air delivering capacities ranges from 2500-100,000 CMH. Our axial flow fans are available in seven sizes from 12” to 48” in diameter. Our fans are used for the various applications such as:
Cooling towers Air heat exchangers for various chemical processes Power generation Petroleum refining and petrochemicals etc.
Ball Mill is used to grind materials into extremely fine powder. It is electrically operated and fitted with slip ring motor. We offer various types of ball mills such as Planetary Ball Mill, Cement Ball Mill, Industrial Ball Mill, Steel Ball Mill etc. We are also one of the well known Steel Ball Mill Manufacturers and Exporters from India. Some of the features of our ball mill are given below:
Output ranges from 1500 Kgs. To 5000 Kgs. Per batch. Ball mill consists of a cylindrical shell into which material is fed. The shell is supported on both ends with the help of bearings mounted on a stand. The shell rotates around a horizontal axis. The support below bearings is fabricated from heavy channel and plates & is machined to give perfect seating. Drive is either by gearbox or pulley. Ball mills operate continuously, the material to be fine grinded is fed inside from one end and discharged at the other through pressure created by the help of an Air Blower. A dust collection system comprising of cyclone separator, bag filter houses, suitable ducting and air blower collects output of ball mill in the form of fine powder. We manufacture ball mill for manufacturing grey oxide used in making Lead acid battery. We manufacture these battery oxide ball mills from mild steel and as per customer's requirements and design specifications. We are also capable of suggesting on the different design aspects to deliver an energy efficient ball mill.
Basket Strainers are used for straining foreign matter from pipe line and provide inexpensive protection of pumps, motors, valves and other mechanical equipments. We offer various types of sturdy and reliable basket strainers such as Sink Basket Strainer, Industrial Filtration Basket Strainer etc. We are one of the prominent Basket Strainer Manufacturers in India. Features of our basket strainers are given below:
Sizes 100 NB to 500 NB Flanged inlet and outlet connections Low-pressure drop Easy to install Different screens available in basket as per fluid to be handle Material of construction - S.s. Free straining areas minimum of 6 times the pipe cross section area
Functioning Unfiltered liquid enters the basket housing and passes down. Solids are contained inside perforated screen in the basket and foreign matters are collected inside perforated screen in the basket.
The foreign material collected is removed when the unit is opened from the top and the basket is cleaned manually.
Our company provides heavy construction and sturdy Cyclonic Dust Collector which is used in the dust collection systems. These dust collectors can also be used as pre cleaners for fine and more efficient dust collection systems such as filter bag houses. We also provide with the complete plant erection, commissioning and installation at the customer’s site. We are one of the well known manufacturers of cyclonic dust collectors.
Designed for combustion air, fluid bed aeration, cooling drying & many other process applications
Maximum pressure available – 60” WG Can be provided with optional suction damper, which can be used to obtain a variety of air configurations Available in 8 discharge positions. Impeller can be either V belt driven or mounted directly on motor shaft. Standard flanged outlets Strong & durable casings are made from heavy sheets & ably supported by angles. Stand is fabricated from heavy channel sections.
We provide highly efficient Dust Collection System which is available nowhere else. We offer various types of sturdy and heavy construction dust collection systems which include Industrial Dust Collection System, Automatic Dust Collection System etc. We are also one of the reliable dust collection Exporters from India.
We manufacture Finned Tube Heat Exchanger by a process in which a continuous strip of fin material is wound spirally on the tube.
The usage of finned tubes gives heat uniformly and increases the heat output depending upon the height of fins per unit length employed.
Fin Material: M.S
Finned Tubes Material: Mild steel
Industrial Finned Tube Heat Exchanger can be manufactured in maximum length of 2 meters along with outside diameter of pipe up to 30 mm dia and the fining can be controlled from 2 to 9 fins per inch.
Finned Pipe / Tube Design Considerations
These Air Cooled Finned Tube Heat Exchangers are usually used in rice mills, tea factories, chemical & pharmaceutical industries.
We are also one of the reliable exporters of Finned Tube Heat Exchangers from India.
We offer one of the exclusive Fume Exhaust Systems which are available nowhere else. Our fume exhaust systems are sturdy, reliable and durable. We offer various types of fume exhaust systems such as Industrial Fume Exhaust Systems, Laboratory Fume Exhaust Systems etc. One of the best equipments and parts are used for the manufacturing of our fume exhaust systems. We provide our fume exhaust systems at competitive prices and also well within the stipulated time. We are also one of the well known fume exhaust systems Manufacturers in India.
We offer sturdy and low maintenance cost Industrial Ovens which are made up of the best quality parts. Our industrial ovens are highly efficient and also give low energy costs. We also offer Industrial Ovens which can be used for small or large volume applications in a variety of temperatures, sizes and configurations. Also, these ovens are used in industries such as chemical, food production, electronics, etc. One can also avail Custom Industrial Ovens from us which are made just according to the customer needs. We are one of the renowned exporters of industrial ovens from India.
Rotary Furnaces are used in secondary smelting units for re -processing Copper / Lead from scrap.
Rotary furnaces have an inner brick lining over which scrap is transformed from solid to molten state due to heat given by oil firing. Oil firing is done with the help of a high -pressure air blower.
For copper smelting & refining: Refined material is discharged into moulds, which are kept in vertical position on trolleys
For Lead smelting & refining: Refined material is discharged into moulds.
Rotary furnace is installed on rotary base. It rotates on heavy wheels mounted on base & for pouring finished material; it is lifted by hydraulic cylinders through a power pack.
The Salient features are: -
Low Fuel Consumption. Long Refractory Lining Life. Reduced Initial Heating Time. Gives more number of batches per shift.
We offer both stainless steel storage tanks and mild steel Metal Storage Tanks. Our Metal Storage Tank is highly efficient and reliable and cannot be availed through anywhere else. We also offer Liquid Storage Metal Tank, Industrial Metal Storage Tank etc. We are on of the well known Manufacturers of metal storage tank. Some of the features of our storage tank are listed below:
Our storage tanks are fabricated using supreme quality stainless steel / m.s. The storage tanks are extensively used for storing of pulp and other liquid / oils. This tank is also corrosion resistant and is available in various sizes and dimensions as per client's requirements and demands. These tanks are absolutely safe and available in size of 1 kg to 3000 kg. The storage tanks are durable and low in cost. These tanks are leak proof.
FRP Storage Tanks
We are providing well - manufactured storage tanks that are used for storage of highly corrosive chemicals. Manufactured as per the client’s requirement, these tanks are non-corrosive, long lasting, leak proof & require less maintenance.
We offer sturdy, reliable and durable Oil Burner which is highly efficient in its working. There are various types of air burners such as Waste Oil Burner, Air Pressure Oil Burner etc. Our burners are available in a variety of designs and therefore it can burn different varieties of oils such as light diesel oil, furnace oil, C.T.F etc. These find usage in various applications such as:
Oil fired furnaces for glass, bricks and ceramics. Bakery ovens Kilns and galvanizing equipments. Varnish pots Tea driers etc.
We offer highly efficient and low maintenance Pulse Jet Bag Filters which have choices for automatic and manual cleaning. We also offer Reverse Pulse Jet Bag Filters, Pulse-Jet Bag Filters etc. which have sturdy construction and low maintenance costs. We also offer services for complete plant erection, commissioning and installation for the customers. We are also one of the well known Pulse Jet Bag Filters manufacturers in India.
Lead oxide is a general term & can be used to describe either – Lead Monoxide – PbO – Litharge
Lead Tetroxide – Pb3o4 – Red Lead – Brilliant Orange Red Pigment. Black or Gray Oxide – 70% PbO + 30% Metallic Lead
Red Lead is used in Ferrous Metal Protective Paints Stationary / Traction / Tubular Plate Batteries Crystal Glass Television Tubes Glazes
Red lead forms through an oxidation process when the raw material (lead oxide from ball mill) is heated to around 450 ° C in a furnace. In the oxidation process, the controlling has to be done of – Lead Oxide Oxygen Temperature Time
After the desired % of Red Lead has been reached, it is discharged & ground in a low impact hammer mill to adjust for particle size, distribution, acid adsorption, apparent density etc.
Process: -
A vertical agitator is used for constant mixing of powder inside the furnace. A vertical shaft supports & turns agitator arms to stir the batch lying on top of furnace.
We offer highly efficient Red Lead Furnaces which also include Litharge Red Lead Furnaces, Red Lead Oxide Furnaces etc. We are one of the reliable red lead furnaces Exporters from India.
Ribbon Blender is used for uniform mixing of dry powders, granules etc. In ribbon blender, Shaft is welded with two sets of spiral ribbons, one inside the other. Inner and outer helical ribbons are accurately proportioned and oppositely pitched to prevent localized material accumulation. We offer various types of Ribbon Blenders such as Stainless Steel Ribbon Blender, Pressure Ribbon Blender, Double Spiral Ribbon Blender etc. We are also one of the well known Manufacturers of ribbon blender in India.
Some of the features of ribbon blender we provide are:
All contact parts made in SS, Top cover also made from SS. Heavy & enlarged base stand assembly on a MS structure.Outboard bearings in rugged cast steel housing Designing of ribbons is done in such a way that it imparts both radial and linear motion for complete homogeneous mixing of material. Shaft sealing on out side with Teflon bush and SS stuffing box. These ribbon blenders are extremely useful in chemical industries, ayurvedic formulation pharmaceutical industries, pesticides and fertilizer and food processing industries and other industries. These are manufactured in a range of 25 Kg to 1000 Kg batch capacity in S.S.
We are one of the reliable exporters of Screw Conveyor from India. We offer various types of screw conveyors which are available in both stainless steel and mild steel construction. We have Screw Conveyor, Industrial Screw Conveyor to offer. These screw conveyors are sturdy, efficient and durable. We make use of the best parts and equipments for the manufacture of our screw conveyors. We have become one of the reliable Exporters of screw conveyor from India.
Two fluids at different temperature flow through Shell Tube Heat Exchanger. One fluid flows through the tube inside and the other flows through tube outside but inside the shell. Heat gets transferred from one fluid to another through tube wall.
We manufacture and supply an extensive series of shell & tube heat exchangers adhering to TEMA/ASME standards. These shell & tube heat exchangers are able to handle high temperature & pressure applications that are suitable for various industrial applications.
We develop and export these exchangers in a wide range of sizes and capacities catering to suit individual applications and purposes.
Heat Exchanger includes boilers, evaporators, super heaters, condensers, and coolers.
We offer various types of Silos which are sturdy, efficient and reliable. Our range of silos encompasses of Steel Silos, Industrial Silo, Commercial Hopper Silo etc. We offer sturdy construction of Hopper Silos. They are used to store bulk material. To meet the demands of different sectors, we also offer the facility of customization. We have the capability to manufacture, different sizes to suit the requirement of our diverse customers. We have become one of the preeminent manufacturers and exporters from India as well.
End Requirement: Temperature attained: - 200 - 250 ° C Material of construction of circulation coil: M.S / S.S. Heat capacity: Up to 3 lakhs Kcal. Insulated with Glass wool from outside
We offer reliable and sturdy Vibrosieves which are available nowhere else. Vibration Sieve is continuous process equipment which provides solution to variety of needs of screening, sifting, classification, grading oversize or undersize, de-dusting, de-watering, de-lumping etc. We also provide customization of Vibrosieves just according to the customer’s requirements. One of the best quality parts and equipments are used to manufacture this product. We also offer Vibrosieves and that too at quite competitive prices. We have become one of the well known Vibrosieves Manufacturers and Exporters from India.
Designed for combustion air, fluid bed aeration, cooling drying & many other process applications
Maximum pressure available – 42” WG Can be provided with optional suction damper, which can be used to obtain a variety of air configurations. Available in 8 discharge positions. Impeller can be either V belt driven or mounted directly on motor shaft. Standard flanged outlets Strong & durable casings are made from heavy sheets & ably supported by angles. Stand is fabricated from heavy channel sections.
Electronica Hi Tech Machines Pvt. Ltd. Manufacturing and supplying of table type spot welding machines, industrial table type spot welding machines, automatic table type spot welding machines and semi automatic table type spot welding machines.
Processing...
