We source and supply superior quality heat shrinkable bus bar insulating tubes. Our tubes are sourced from reliable manufacturers to ensure efficiency. Our insulating tubes avoids short circuit fault caused by small animals such as mice, snakes and so on. Our tubes prevent bus bar from chemical corrosion effected by strong acid, alkali & salt and thereby minimizing accidental injure.

Specifications:
 
Test Item Value:

• Volume resistivity: 4.3 x 1014 ©.cm
• Dielectric strength: 25kv/mm
• A.C. voltage withstand: 42kv,1min
• Thunderbolt impact: 75kv Peak

 Flammability Pass:

• Suitable for 11 & 33 KV
• Sizes from 30 mm to 150 mm
• Color-Red

We provide heat shrinkable anti-tracking insulation tubes that are sourced from reliable and trusted manufacturers. Our insulation tubes are widely used owing to the following salient features:

• Material: polyolefin
• Operating temperature: -55'C - 100'C
• Shrink temperature: Start at 100"C, and shrink totally at 130'C
• Standard Color: red
• Application: Suitable for termination kits for XLPE Cable, PILE Cable up to 36 kV

Test Method
 
Our insulation tubes are tested for standard value, operating temperature, tensile strength, elongation, dielectric strength, tracking resistant, volume resistivity, dielectric constant, longitudinal shrinkage, eccentricity, water absorption flammability, (oxygen index) copper corrosion, cold bend and others.

We source and supply pure silicon rubber tubes which are fabricated using raw material sourced from Japan and USA. Our tubes are used for electric product, lighting fixture and in medical equipment. Our tubes are appreciated for high transparent, half-transparent, milky white and flame-resistance.

Specifications:

• Diameter: 1-30mm
• length: 50m/roll or 100m/roll
• Break down voltage: 7000V,10000V
• Temp Withstanding:-60---200°C
• Color: milky white, clear or yellow

We offer flame retardant heat shrinkable tubes which are environment friendly due to the formulation using high polymers, through cross-link by electronic accelerator and continuous expansion. Some of the salient features such as flexibility flame retardant, quick shrink and stable performance make these suitable for applications in the field of electronics, communication, automobile and widely applied for connecting or end-handling, electric wire, insulating and harness of electric wire, corrosion and rust-proof of metallic rods or tubes, antenna protection and marking for other products.
 
Characteristics

• Operating temperature: -55°C-125°C
• Shrinking Temperature: Start at 70°C, and shrunk totally at 110°C
• (for thin wall-CB) or 125°C (for normal wall), longitudinal shrink ratio: 8%
• Flexible, flame retardant
• Sizes: from0.6~180mm,
• Easy for use, using oven or heating gun and it will shrink.
• Meet RoHS standard.
• Standard Colors: Black, White, Red, Yellow, Green, Purple, Blue, Grey, Brown (Other color available upon request)
  

Technical Data

Property	Test Method	Standard
Physical	Tensile strength (Mpa)		GB/T 1040	≥ 10.4
	Elongation%		GB/T 1040	≥200
	Tensile Strength after Aging(Mpa)		UL 224 158??Cx168hr	≥7.3
	Elongation after Aging%		UL 224 158??Cx168hr	≥100
	Heat Resistance		UL 224 250??C x 4hr	No viscidity No cracking
Electrical	Cold Blend		UL224-30??Cx4hr	No cracking
	Dielectric Strength (kV/mm)		GB/T1408	≥15
	Dielectric Withstand	150 V	UL 224	No breakdown for 1500 W
		600 V	UL 224	No breakdown for 2500W
	Volume resistance (??.cm)		GB/T1410	≥1x10
Chemical	Anti Corrosion		UL 224 158??Cx168hr	Pass
	Copper stability		UL224 158??Cx168hr	Pass
	Flammability		UL 224	VW-1

Our dual wall heat shrinkable tubes are flame retardant cross-linked polyolefin, with an inner coating hot-melt adhesive and an outer layer that shrinks to provide electric and mechanical protection. These are used for insulating and sealing electric wirings.Our dual wall heat shrinkable tubes are flame retardant cross-linked polyolefin, with an inner coating hot-melt adhesive and an outer layer that shrinks to provide electric and mechanical protection. These are used for insulating and sealing electric wirings.
                      
Characteristics:
 

• Operating Temperature: -45??C~ 125??C
• Shrink temperature: Start at 70??C; shrunk totally at 120??C
• Inner layer glue melt temperature: 70-90??C
• Shrink ratio: 3:1, 4:1,
• Longnitudinal Shrink ratio≤8%
• Waterproof, RoHS compliant
• Standard Color: Black (Other color available upon request)

Technical Data

Property	Test method	Standard
Tensile Strength (Mpa)	ASTMD 2671	≥12
Elongation at Break	ASTMD 2671	≥300
Tensile Strength after aging(Mpa)	UL 224 158??Cx168h	≥7.3
Elongation at Break after aging (%)	UL224 158??Cx168h	≥200
Dielectric Strength	IEC243	≥15
Volume Resistance	IEC93	≥1x 10

Hot melting adhesive property

Property	Test method	Standard
Water Absorption	ASTM-D570	<0.2%
Vicat Softening Point	ASTM-E8	95??C
Peel Strength (PE)	ASTM-D1000	120N/25m
Peel Strength(AL)	ASTM-D1000	80N/25m

W-1-SB (4X) Specifications:

Size	As supplied Min.I.D.	After Recovered (mm)	Standard package m/spool or m/pc
Mm	inch	Max.I.D.	TotalW.T.	Adhesive thickness
??4.0	------	4.0	1.0	1.0±0.15	0.4±0.15	200
??6.0	------	6.0	1.5	1.1±0.15	0.4±0.15	100

	Mylar Tube We source and offer mylar heat shrinkable and non-heat shrinkable tubes which is procured from reliable and trusted manufacturers. Our spiral tubes are fabricated using NOMEX® .MYLAR®, or KAPTON ® with different shrinkage rate. Our tubes are used in thermostat, motors or transformers. Specifications: Insulating Material Thermal Class °C Shrinkage % Dielectric KV/mm MYLAR,,,A 130 - 280 MELINEX,,,238 140 - 280 MYLAR,,,HS 130 35 280 MYLAR,,,,SCS (Clear) 130 8 ~ 12 280 MYLAR,,,,KBS (Hazy) 130 8 ~ 12 280 NOMEX,,,MYLAR,,,,A 155 - 50 ~ 200		Send Your Enquiry

	Send Your Enquiry		Thin Wall Flexible PVDF Tubing We source and supply superior quality thin wall flexible PVDF tubing (H-150K) which are excellent flame-retardant heat-shrinkable polyvinylidence fluoride tubes. Our tubes are ideal for applications which require high -temperature resistance, outstanding abrasion and cut-through resistance or superior chemical and solvent resistant properties. Our tubing protects solder joints, terminals and connections from most industrial fuels, solvents and chemicals. The glass-like appearance enhances to inspect the mark on protected harness. Specification:  Minimum fully recovery temperature: 135??C Approvals: UL, VW-1, File No E249362 Meet: SAE-AMS-DTL-23053/18 Standard color: Clear, Black Technical Data Property Test Method Typical Data Operating temperature IEC 216 -55°C to 150°C Un-aged Tensile strength ASTM D 2671 Min.30 MPa Elongation ASTM D 2671 Min.150% After Aging Elongation 180° C, 168hrs. Min.100% Heat shock 250°C, 4hr No cracking Cold bend -55°C, 4hr. No cracking Dielectric Strength UL224 Min.2.5KV/1minute Volume resistance ASTM D 876 Min.10° cm Flammability VW-1 Pass Copper corrosion 180°C, 168hrs No corrosion Copper stability 180°C, 168hrs No sigh of Degradation

	Chemical Resistant PVDF Tubing Our high temperature chemical resistant PVDF tubing (H-175K) is a semi-rigid, excellent flame-retardant hear-shrinkable polyvinylidene fluoride (PVDF) tube. Our tubing is ideal for applications requiring high-temperature performance, outstanding abrasion and cut-through resistance or superior chemical and solvent resistant properties. The PVDF tubing protects wires, solder joints, terminals, connections and components from most industrial fuels, solvents and chemicals. Specifications: Operating temperature:-55deg C to 175 deg C Meet: SAE-AMS-DTL-23053/8 Minimum shrink temperature: 175 deg C Standard color: Clear Technical Data Property Test Method Typical Data Operating temperature IEC 216 -55°C to 175°C Un-aged Tensile strength ASTM D 2671 Min.34.5 MPa Elongation ASTM D 2671 Min.150% After Aging Elongation 250° C, 168hrs. Min.50% Heat shock 300°C, 1hr No cracking Cold bend -55°C, 1hr. No cracking Dielectric Strength ASTM D 2671 Min.30KV/mm Volume resistance ASTM D 876 Min.10° cm Flammability VW-1 Pass		Send Your Enquiry

	Send Your Enquiry		HTG Fiberglass Sleeving We provide HTG Sleeving which is a non-alkali fiberglass braided sleeving with special resin coated. Our sleevings has tensile strength and heat resistance of 450°C. Our range finds its applications as an excellent insulating material for the wiring of electrical machinery and electrical appliances.

	Fiberglass Insulation Sleeving Our silicon rubber fiberglass insulation sleeving is sourced from reliable and trusted manufacturers. Our insulation sleeving is a class H high voltage withstanding sleeving and is used for class H motor, electrical appliance, heating equipment and special lighting fixture.   Specifications: Diameter:0.5----30mm length: 1 meter per pc or 100m/roll Breakdown Voltage: 4000V Class:H Color: White, black, red etc.		Send Your Enquiry

	Send Your Enquiry		Acrylic Fiberglass Insulation Sleeving We supply optimum quality acrylic fiberglass insulation sleeving which is fabricated using non-alkali fiberglass with acrylic resin coated. Our insulation sleeving is appreciated for heat resistance and excellent dielectric. Our insulation sleeving is ideal for applications as wiring insulation for motors, electrical instruments etc.   Specifications: Diameter: 0.5 - -30mm Length: 1 meter per pc or 00m/roll Breakdown Voltage: 1500V, 2500V, 4000V Class: F Color: Natural, black, yellow

	Polyster Tapes We supply optimum grade polyester and PVC tapes which are sourced from reliable and trusted manufacturers across the globe. Our polyester and PVC pipes are widely used across different industries owing to their salient features such high dielectric strength and tensile strength.    Technical Specifications: &   Polyester Backing mils Total thickness mils(mm) Adhesion to steel oz/in(N/cm) Tensile Strength lbs/in (N/cm) Dielectric Strength Total Volts Temp Rating °C Acrylic: Elongation 100%.Abrasion & moisture resistant. Applications: coil wrapping, anchoring, harnessing, holding, slot edging in transformers and motors. 51562 Flame retardant temperature& abrasion resistant. Excellent electrical insulating properties. Good for inter-layer insulation. Yellow, White 2 3.5 (0.089) 45 (4.9) 50(88) 7500 130 51589 Solvent resistant. Excellent long-term aging characteristics. Black, clear, Yellow. 1 2.2 (0.056) 35(3.8) 25(44) 5000 130 51592 Solvent resistant. Excellent long-term aging characteristics. Yellow. 2 3.7 (0.094) 55(6.0) 50(88) 7500 130 54113 High temperature shear, abrasion and puncture resistant. Ideal for film wrap capacitors and where maximum insulation builds up is required. Clear, Yellow. 1 2.4 (0.061) 45(4.9) 25(44) 5000 130 54143 High temperature Shear and abrasion resistant. Ideal for film wrap capacitors & where max.insulation builds up is required. Clear, yellow. 1.4 3.0 (0.076) 50(5.5) 38(66) 6000 130 Rubber Thermosetting: Elongation 100%.Tough & comfortable. Abrasion & moisture resistant. Excellent electrical insulating properties. 51587 Resists chemicals & solvents when thermoset.Excellent electrical insulating properties.Yellow,Black.MIL-1-15126F MF 2.5 1 2.2(0.056 50(5.5) 25(44) 5000 130 51588 Resists chemicals & solvents when thermoset.Excellent electrical insulation properites.Clear.MIL-1-15123F MF 2.5 1 2.2(0.056) 50(5.5) 25(44)		Send Your Enquiry