The range of hand tools supplied by us are of superior quality. The material used are good quality iron and polish.

• Screw Driver Bits


• Ordinary Pliers


• Electronic Pliers


• Bit Holder With handles

Insulation Test Standards:
Insulation according to IEC 900 ASTM F – 1505-01 New VDE 0682/part 201, DIN 7437, NFPA 70 E. Each safety tool individually tested to 10000 Volts and certified to 1000 Volt AC or 1500 Volt DC

We have a wide range of general hand tools that are used in various industries like automobiles, engineering, steel etc. The tools are available in various sizes.

Our range of non-sparking, non-magnetic, corrosion resistant tools are backed by a lifetime warranty, except for countries
where a lifetime warranty is not allowed, by local law or verdicts, (e.g. Germany where the warranty is limited to 30 years). If an Ampco tool breaks or fails to perform under normal service, it will be repaired or replaced without charge. Normal service wear or breakage, due to abuse or misuse, is not covered by the warranty.

5-Piece Complete Tune-up Kit .
This garage equipment and  tools kit provides the necessary tools to easily tune-up most imported and domestic vechicles with conventional, electronic, distributor less(DIS) and computer controlled ignition systems.

• 591 212 Compressure Tester


• 591 220 Vacuum/Fuel Pump Tester


• 591 230 Remote Starter Switch


• 591 531 Inductive Timing Light


• 591 100 Digital Multimeter

Other special automotive tools for clutch, engine and body work as well as for assembly non scratching tools.

Our torque tools have the following features:

Features

• Screwdriver with a fixed, pre-set torque setting


• Comfortable multi-component handle with soft zone for optimum torque transfer


• Accuracy 6%, acc. to EN ISO 6789, BS EN 26789, ASME B107.14M


• T-handle with fixed, pre-set torque setting to transfer higher torques


• Accuracy 6%, acc. to EN ISO 6789, BS EN 26789, ASME B107.14M


• With slipping clutch, triggered automatically

The X-4 Torque Multiplier is a Geared Head Wrench incomparable to any other tool. The multiplication is achieved through a planetary gear train at a ratio depending on the model. The precision gear train is totally enclosed.
An X-4 is a silent partner to all maintenance men, providing ample power to loosen the toughest threaded fasteners. As a torque multiplier it generates torque''s from a few hundred pound-feet to thousands of pound-feet with precision and ease.

Relatively small in size, the X-4 torque multipliers may be used with practically all accessory tooling yet provide ample wrench power in limited work areas. In many cases it eliminates dismantling of nearby equipment.
In addition to many applications where an X-4''s use is mandatory, general use will not only upgrade the quality of work but also vastly improve the overall efficiency of the operators.

Safety groups will find many reasons for specifying the use of X-4 Torque Multipliers and rather than interfere with production or efficiency, both factors will show improvement.
In use, standard drive sockets of appropriate size are placed on the male drive square. A suitable drive tool is inserted in the female input socket. This may be an ordinary ratchet drive, a torque measuring device or under controlled conditions, a power drive.

This assembly is now placed on the part to be turned with the reaction bar restrained against some substantial part of the equipment being serviced. At this point, any force applied to the input drive is multiplied at the output end of the X-4. For higher ratios of multiplication, two or more X-4''s may be directly intercoupled. Impact type driving tools should not be used.
Thousands of X-4 torque multipliers are in use throughout the world as maintenance, production, inspection or service equipment wherever high torque applications are found.

Rahsol or Dremotec Torque Wrenches made of high strength aluminium alloy. Available for variety of areas of application in the controlled screw tightening.
Robust and unsusceptible the full metal construction makes dremometer torque wrench particularly unsusceptible to grime and rough handling on construction sites, in work shops and in industry. Torque wrenches available from 6 NM - 2000NM in different models

This product is suitable for steel, stainless steel, cast iron and stone cutting.
It is also awarded with the Chinese National Standard "CNS" certification mark as one of the TAILIN stylish products. Tailin cut-off wheels offer a full range of wheel sizes and specifications for any cutting need

• ABRASIVES:
A: steel, iron

C: aluminum, copper, cast iron, stones

WA: stainless steel, alloy steel

• GRIT: #20 #24 #30 #36 #46 #54 #60

• GRADE: P. Q . R . S . T .