Seccolor makes a range of doors and door frames out of galvanized color coated steel (CCS), stainless steel, GI and CRCA. Panel Doors made of CCS/SS can be either partly or fully glazed. Laminated board can be used as infill (fully or in part). Door frames in CCS, SS, GI or CRCA are made in various shapes and sizes of sections with or without provision for gaskets with various rebates depending upon the thickness of the shutter and with or without provision for Fly Mesh shutter.

UPVC (Unplasticised Polyvinyl Chloride) & only those additives are used that are essential in producing sound extrusions in accordance to BIS 7413:1991. The main profiles shall be multi chambered with a min. of three chambers. The central chamber, being for reinforcement shall be fully sealed when main profiles are welded at joints. Water drainage path is in a separate chamber & does not affect the integrity of the central chamber. All profiles are tested regularly for heat reversion, heat ageing, impact resistance & weld factors in accordance to BS 7413:1991. Profiles are tested regularly for welded corner strength. The welded joint shall never fail below a stress level of 20 Mpa. On whole, when properly manufactured, windows & doors shall confirm to & comply with the specifications & standards of BIS 6375 Part 1 & 2. All reinforcements for profiles shall be either MS sheet hot dip zinc coated of grade N in compliance with BS 2989 or extruded aluminium alloy grade 6063 or 6082 in compliance with BS 1474.

Seccolor Partition / Curtain Glazing fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (Base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 GM/Sq.mtr) with total coated thickness of 0.55mm. Sections for shutter should be of 46x46mm and external frame should be of 46x52mm. Section for glass beading should be of 18x25mm and centre mullion should be of 46x70mm. Handle made of high grade Aluminium powder coated and with nylon receiver. Gaskets made of Ethyl Propylene Diamine Monomer (EPDM). Corner brackets made of CRCA with zinc phosphating. Mullion caps made of Glass filled nylon. The frame and shutter sections are to be cut to length, mitre joined with corner bracket. Centre mullions are to be fixed using mullion cap. Shutters & fixed portion should be paneled with 4 – 12mm glass.

Seccolor Structural Glazing fabricated from roll formed sections made of galvanized Steel colour coated/ powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 Gm/Sq.mtr.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade stainless steel of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel/ powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. The section should be of 50x100x0.72mm/ 33x58mmx0.72mm for frame verticals, 33x58mm for frame horizontals section for reinforcement should be of 48x98mm/ 31x56mm, glass holding section should be of 32.5x37mm for top and bottom grids in between should be of 32.5x18mm. Reflective glass 4 – 6mm toughened/ untoughened may be use.

Laminated wooden flooring of KRONO AC-3/ AC-4, size - 1210 x 193 x 8mm suitable for heavy domestic/ light commercial use having properties like water resistance, impact resistance, heat resistance, resistance to cigarette burns, stain resistance and resistance to dust mite & non fading. A/T profile size 2100 length.

WALL:

The walls are to be made of GI profile cement sheet & expended polystyrene core insulation. The bottom track is to be of “U” profile made of GI sheet 1.0 mm thick fixed by suitable dash fastener on the cement platform. The wall panels of width 1.22m are of 2 Nos. of 10mm thick NCL Bison Panel (Asbestos free) confirming to IS 14276 with 27mm gap in between filled with 27 mm thick expended polystyrene core having bulk 16kg/cum duly bonded with poly vinyl acetate base bonding compound. These sandwich panels are joined with one another duly fitted to the bottom track and the all round the edges of the panels are inserted with “H” profile GI steel section 0.63mm thick held in between “H” shaped G.I. 0.63mm thick profiles. The topsides will be concealed with “U” shaped top track of 1.0mm thickness and corners ends of the walls. Heights of the wall are approx 10’-0” or are kept as per customer’s requirements.

ROOF:

Made out of Prepainted steel sheet 0.50mm thick fixed with suitable “j” hook / bolts and nuts. Sheet fixed suitably to steel box / section purlin, Trusses & Column.

COLUMNS, TRUSSES & PURLINS:

Columns are made of standard suitable MS BOX as per design. Trusses are also made of steel box section of suitable size as top and bottom chards and as struts and purlins are made of steel box sections of suitable sizes of MS Box sections complete as per our design. (The trusses, column & purlins are designed as per recommended standards by qualified structural as per the span & design requirement.)

DOOR AND WINDOW:

M.S. door and windows will be provided.

FALSE CEILING:

3.2 mm thick Decocil Panel with Thermocol pasted over it fixed and G.I. “T” Grid.

PAINTING:

Internal OBD & Exterior with roller finish. Steel section to be primered and applied Enamel paint.