We are one of the leading manufacturers of single phase stabilizer air cooled which is widely in demand amongst our clients. These are highly efficient and energy saving and possess following specifications:
 
Technical Specifications :

Technical Specifications	Single Phase (L-N)	Three Phase (L-L)
Stabiliser type	Servo Stabiliser with O/P sensing feed-back system
Type of cooling	Air cooled / Oil cooled
Model	-	Balanced / Unbalanced
Servo motor drive	A.C. synchronous stepper motor
Input voltage range	170–270 V	360–460 /340–480 /310–480 V
Nominal output voltage (Internally Settable to)	230 V ± 1% (220 V or 240 V)	415 V ±1% (380 V or 400 V)
Voltage correction speed	25 Volts/Sec (L–N)	48 Volts/Sec (L–L)
Single phasing prevention	NA	By voltage sensing method
Input frequency	47 – 53 Hz
Output voltage regulation	± 1% of the set output voltage
Waveform distortion	Nil
Effect of load pf on output voltage	Nil
Efficiency	> 97 %
Output electronic under/over voltage protection	Upper Limit: 5% (± 2 V) above nominal voltage Lower Limit: –10% (± 2 V) below nominal voltage
Output electronic overload cut-off	Operative above 110% of rated out put current
Short circuit protection	Fuse at the input
Resetting mode	Manual / Auto restart with 15 seconds time delay
Stabiliser bypass switch	Optional	Built-in upto 50 kVA
Input / Output cable terminations	5-way terminal connector	7-way terminal connector
Front Panel Display / Indications	Digital voltmeter to read O/P voltage	Digital voltmeter to read
	I/P Present LED	O/P voltage
	O/P Normal LED	R / Y / B-Phase LED
	High Cut-off LED	O/P Normal LED
	Low Cut-off LED	High Cut-off LED
	Over-load LED	Low Cut-off LED
Standard Product Ratings	1 kVA - 20 kVA	Aircooled - 3 kVA - 60 kVA Oilcooled - 3 kVA - 1000 kVA

Adopting latest technological developments, we offer a wide range of Three Phase Stabilizer Air Cooled which caters to varying needs of our clients. These are customized as per the specifications of our clients and are qualitatively superior.

Technical Specifications :

Technical Specifications		Three Phase (L-L)
Stabiliser type	Servo Stabiliser with O/P sensing feed-back system
Type of cooling	Air cooled / Oil cooled
Model	-	Balanced / Unbalanced
Servo motor drive	A.C. synchronous stepper motor
Input voltage range	170–270 V	360–460 /340–480 /310–480 V
Nominal output voltage (Internally Settable to)	230 V ± 1%	415 V ±1%
	(220 V or 240 V)	(380 V or 400 V)
Voltage correction speed	25 Volts/Sec (L–N)	48 Volts/Sec (L–L)
Single phasing prevention	NA	By voltage sensing method
Input frequency	47 – 53 Hz
Output voltage regulation	± 1% of the set output voltage
Waveform distortion	Nil
Effect of load pf on output voltage	Nil
Efficiency	> 97 %
Output electronic under/over voltage protection	Upper Limit: 5% (± 2 V) above nominal voltage
	Lower Limit: –10% (± 2 V) below nominal voltage
Output electronic overload cut-off	Operative above 110% of rated out put current
Short circuit protection	Fuse at the input
Resetting mode	Manual / Auto restart with 15 seconds time delay
Stabiliser bypass switch	Optional	Built-in upto 50 kVA
Input / Output cable terminations	5-way terminal connector	7-way terminal connector
Front Panel Display / Indications	Digital voltmeter to read O/P voltage	Digital voltmeter to read
	I/P Present LED	O/P voltage
	O/P Normal LED	R / Y / B-Phase LED
	High Cut-off LED	O/P Normal LED
	Low Cut-off LED	High Cut-off LED
	Over-load LED	Low Cut-off LED
Standard Product Ratings	1 kVA - 20 kVA	Aircooled - 3 kVA - 60 kVA

We manufacture a wide range of Single Phase Stabilizer Oil Cooled which is designed and developed as per the specifications of our clients. Qualitatively superior, these are known for optimum performance and energy efficient operations.

Technical Specifications :

Technical Specifications	Single Phase (L-N)	Three Phase (L-L)
Stabiliser type	Servo Stabiliser with O/P sensing feed-back system
Type of cooling	Air cooled / Oil cooled
Model	-	Balanced / Unbalanced
Servo motor drive	A.C. synchronous stepper motor
Input voltage range	170–270 V	360–460 /340–480 /310–480 V
Nominal output voltage (Internally Settable to)	230 V ± 1% (220 V or 240 V)	415 V ±1% (380 V or 400 V)
Voltage correction speed	25 Volts/Sec (L–N)	48 Volts/Sec (L–L)
Single phasing prevention	NA	By voltage sensing method
Input frequency	47 – 53 Hz
Output voltage regulation	± 1% of the set output voltage
Waveform distortion	Nil
Effect of load pf on output voltage	Nil
Efficiency	> 97 %
Output electronic under/over voltage protection	Upper Limit: 5% (± 2 V) above nominal voltage Lower Limit: –10% (± 2 V) below nominal voltage
Output electronic overload cut-off	Operative above 110% of rated out put current
Short circuit protection	Fuse at the input
Resetting mode	Manual / Auto restart with 15 seconds time delay
Stabiliser bypass switch	Optional	Built-in upto 50 kVA
Input / Output cable terminations	5-way terminal connector	7-way terminal connector
Front Panel Display / Indications	Digital voltmeter to read O/P voltage I/P Present LED O/P Normal LED High Cut-off LED Low Cut-off LED Over-load LED	Digital voltmeter to read O/P voltage R / Y / B-Phase LED O/P Normal LED High Cut-off LED Low Cut-off LED Over-load LED
Standard Product Ratings	1 kVA - 20 kVA	Aircooled - 3 kVA - 60 kVA Oilcooled - 3 kVA - 1000 kVA

Fabricated using superior quality raw material, our range of Three Phase Stabilizer Oil Cooled is widely in demand in the market. Designed and developed as per the specifications of our clients, these are qualitatively superior and known for excellent performance.

Technical Specifications :

Technical Specifications		Three Phase (L-L)
Stabiliser type	Servo Stabiliser with O/P sensing feed-back system
Type of cooling	Air cooled / Oil cooled
Model	-	Balanced / Unbalanced
Servo motor drive	A.C. synchronous stepper motor
Input voltage range	170–270 V	360–460 /340–480 /310–480 V
Nominal output voltage (Internally Settable to)	230 V ± 1% (220 V or 240 V)	415 V ±1% (380 V or 400 V)
Voltage correction speed	25 Volts/Sec (L–N)	48 Volts/Sec (L–L)
Single phasing prevention	NA	By voltage sensing method
Input frequency	47 – 53 Hz
Output voltage regulation	± 1% of the set output voltage
Waveform distortion	Nil
Effect of load pf on output voltage	Nil
Efficiency	> 97 %
Output electronic under/over voltage protection	Upper Limit: 5% (± 2 V) above nominal voltage Lower Limit: –10% (± 2 V) below nominal voltage
Output electronic overload cut-off	Operative above 110% of rated out put current
Short circuit protection	Fuse at the input
Resetting mode	Manual / Auto restart with 15 seconds time delay
Stabiliser bypass switch	Optional	Built-in upto 50 kVA
Input / Output cable terminations	5-way terminal connector	7-way terminal connector
Front Panel Display / Indications	Digital voltmeter to read O/P voltage I/P Present LED O/P Normal LED High Cut-off LED Low Cut-off LED Over-load LED	Digital voltmeter to read O/P voltage R / Y / B-Phase LED O/P Normal LED High Cut-off LED Low Cut-off LED Over-load LED
Standard Product Ratings	1 kVA - 20 kVA	Aircooled - 3 kVA - 60 kVA Oilcooled - 3 kVA - 1000 kVA &l

We manufacture a precision engineered range of ultra isolation transformer that is known for excellent performance. These are customized as per the specifications of our clients and comply with international quality standards.

Specifications :

Technical Specifications	Single Phase (L-N)	Three Phase (L-L)
Transformer type	Naturally Aircooled for indoor application
Transformation Ratio	1 : 1 (Also Step-up / Step-down)
Primary Voltage	230 Volts 1 PH (L-N)	415 Volts 3 PH (L-L)
Secondary Voltage	110 V (OR) 230 V 1 PH	200 (OR) 415 V 3 PH (L-L)
Connection	-	Delta - Star
Input frequency range	47 – 53 Hz
Regulation	2 – 4% for 100% change in current @ unity pf
Type of lamination	CRGO (Cold Rolled Grain Oriented)
Working temperature	0 to 50°C & RH of 95% non-condensing at 40°C - Complied
Class of Insulation	Class ‘F’ for Air Cooled / Class 'B' for Oil Cooled
Insulation Strength	Withstands 2.5 kV for 1 minute
Efficiency	> 97 %
DC Galvanic Isolation	> 1000 Mega Ohms
Common Mode Noise Rejection	> 100 dB
Operating Power Factor	0.75 lagging to 0.75 leading
Input / Output cable terminations	Suitable termination arrangement for cable terminations and gland plates for fixing cable glands
Standard Product Ratings	1 kVA - 20 kVA	Aircooled - 3 kVA - 60 kVA Oilcooled - 3 kVA - 500 kVA

Features:
 

• Ultra Isolation Transformer (UIT) be physically located as near to the load as possible
  
• Dedicated Earth to be provided by the customer for the output of the isolation transformer

Our range of CVT (constant voltage transformer) operates at a relatively constant frequency providing substantial constant output voltage in spite of large changes in the input voltage. This power equipment comprises a high resistance transformer which has an air gap in a magnetic shut for providing a constant voltage output. Resonant action of the secondary winding of the transformer and the capacitor is responsible for the whole action.

 

Advantages:	Disadvantages:
1.No moving Parts 2.Faster correction rate (Almost instantaneous) 3.Provides Isolation from Electrical noises 4.Inherent short circuit protection	1.Output voltage is frequency dependent 2.Bulky & expensive compared to other   stabilisers

 
Technical Specifications :

Technical Specifications	Single Phase (L-N)
Transformer type	Ferro Resonant
Type of Cooling	Natural Aircooled; 2 kVA and above (Fan Cooling)
Input Voltage	90–130 /170–270 /310–460 V – 50 Hz
Output Voltage	110 V (OR) 220 / 230 Volts 1 PH
Output Voltage Indication	Analog Voltmeter
Effect Of Frequency	The output voltage will vary 1.6% for a variation of 1% (0.5Hz) Input frequency
Load Regulation	±5V
High & Low Cutoff	Electronic
Working temperature	- 5° C to 50° C
Class of Insulation	Class “B” (Upto 1.5 kVA) Class “F” (2 kVA and above)
Waveform Distortion(Nominal I/P Voltage 230 V)	5% (approx.) at full load
Output waveform	Sinusoidal
Harmonic Distortion	Integrated filter choke
Short Circuit & Overload Protection	Intrinsic & Instantaneous
Input / Output cable terminations	Suitable termination arrangement for cable terminations and gland plates for fixing cable glands
Standard Product Ratings	100 VA – 5000 VA

Note:

1) Avoid using CVT for high inductive loads.
2) Switch ON the CVT before switching ON the load & while switching OFF switch OFF the load  first and then the CVT.
3) Check the frequency before using the CVT with a generator.
4) Keep magnetic storage & display devices like diskettes, Monitors, etc., away from the CVT.
5) Switch OFF the CVT when not in use.

Supplying a wide range of power transformer, we are satisfying the ever increasing demands of our clients. These are qualitatively superior and can be customized as per the specifications of our clients. Our power transformers are robust in design and rugged in construction. These transformers maintain a constant voltage and are corrosion resistant.  

Following international manufacturing standards, we have been fabricating a qualitatively superior range of UPS-Single Phase. These are available in various models and can be customized as per the specifications of our clients.

Features:

• State-of-the-art IGBT System provides pure sine waveform
  
• High frequency design - Reduces the loss and noise
  
• Wide Input operating voltage range - Enhances the battery life
  
• LCD Display - Indicates I/P and O/P Voltage, I/P and O/P Frequency, Battery Capacity, Load Capacity and UPS Status indications
  
• Compact in size with small footprint and pleasing looks
  
• Complete protection against Over load, high/low voltages, low battery, short-circuit and Hot-Ground reversal, etc
  
• User friendly Power management and Auto shut down software

Technical Specifications:

Model	HF1	HF1X	HF2	HF2X	HF3	HF3X
	Capacity		2 kVA / 1.4 kW		3 kVA / 2.1 kW
Input Voltage	160 to 300 V AC (70% to 100% load), 140 to 300 V AC (50% to 70% load), 118 to 300 V AC (0% to 50%)
Input Frequency	50 Hz /- 5 Hz
Input Power Factor	> 0.97
Efficiency	> 89%
Battery Voltage	36 V DC		96 V DC
Battery Type	Lead Acid SMF / Tubular
Battery	12V 7AH 3 Nos.	External	12V 7AH 8 Nos.	External	12V 7AH 8 Nos.	External
Back-up time (in mts)	15 - 20	-	20	-	15-20	-
Output Voltage	220 V AC /- 2%
Output Frequency	Synchronous with input in the mains mode, maintained at 50 Hz /- 0.5% in the battery mode.
Overload	> 150% for 200 milli seconds and transfer to bypass
Output Wave form	Sinewave
Output THD	< 3% for 100% Linear Load
Transfer time	Zero
Alarms	Power Outage - Beeps every 4 seconds Low Battery - Beeps every second UPS Failure - Continuous Beep
Computer Interface	RS 232 Serial
Software	Power Management & Auto Shutdown
Environment Temperature -

We are one of the leading manufacturers, exporters and suppliers of UPS three phase of supreme quality for our clients. We have been engaged in manufacturing a precision engineered range of Ups-Three Phase which is fabricated using superior quality raw material. Qualitatively superior, these are available in customized as well as standardized models.

To overcome the daily power cut hassles, we offer a wide range of Home UPS (Domestic Inverter). These are qualitatively superior and can be customized as per the specifications of our clients.

Features: 

• True Online - State-of-the-art IGBT System provides pure sine waveform
  
• High frequency design - Reduces the loss and noise
  
• Wide Input operating voltage range - Enhances the battery life
  
• LCD Display - Indicates I/P and O/P Voltage, I/P and O/P Frequency, Battery Capacity, Load Capacity and UPS Status indications
  
• Compact in size with small footprint and pleasing looks
  
• Complete protection against Over load, high/low voltages, low battery, short-circuit and Hot-Ground reversal, etc
  
• User friendly Power management and Auto shut down software

Specifications :

VERTEX HF Series On-line UPS
Model	HF1	HF1X	HF2	HF2X	HF3	HF3X
	Capacity		2 kVA / 1.4 kW		3 kVA / 2.1 kW
Input Voltage	160 to 300 V AC (70% to 100% load), 140 to 300 V AC (50% to 70% load), 118 to 300 V AC (0% to 50%)
Input Frequency	50 Hz /- 5 Hz
Input Power Factor	> 0.97
Efficiency	> 89%
Battery Voltage	36 V DC		96 V DC
Battery Type	Lead Acid SMF / Tubular
Battery	12V 7AH 3 Nos.	External	12V 7AH 8 Nos.	External	12V 7AH 8 Nos.	External
Back-up time (in mts)	15 - 20	-	20	-	15-20	-
Output Voltage	220 V AC /- 2%
Output Frequency	Synchronous with input in the mains mode, maintained at 50 Hz /- 0.5% in the battery mode.
Overload	> 150% for 200 milli seconds and transfer to bypass
Output Wave form	Sinewave
Output THD	< 3% for 100% Linear Load
Transfer time	Zero
Alarms	Power Outage - Beeps every 4 seconds Low Battery - Beeps every second UPS Failure - Continuous Beep
Computer Interface	RS 232 Serial
Software	Power Management & Auto Shutdown
Environment Temperature -

Available with us is a precision engineered range of RFI, EMI fliter & surge suppressor and components. Besides, we also offer Lightning & Surge Suppressers that are used in wide industrial applications.

Specifications:

We offer a wide range of EMI Filters and Suppression components. In addition we can also offer Lightning & Surge Suppressers for various applications. Most of the filters are custom built are designed as per the customer requirement.

• SINGLE PHASE, HIGH PERFORMANCE TYPE
  
• VOLTAGE: - 110/240V AC, CURRENT: - 1 to 30 Amps
  
• SINGLE PHASE, GENERAL PURPOSE TYPE
  
• VOLTAGE: - 110/240V AC, CURRENT: - 1 to 100 Amps
  
• THREE PHASE, GENERAL PURPOSE TYPE
  
• VOLTAGE: - 440V AC, CURRENT: - 1 to 100 Amps
  
• THREE PHASE, HIGH PERFORMANCE TYPE
  
• VOLTAGE: - 440V AC, CURRENT: - 1 to 150 Amps

Further, our range of filters can be customized as per the specifications of our clients.

Specifications:

• Rating up to 200A & 440V AC
  
• Higher voltage ratings on request

We offer our servo stabilizer range of products on rental basis. Our range of products is very robust and is made to work continuously for long. These stabilizers can easily bear high electricity load and can be installed anywhere. Ligh in weight, we offer our stabilizers with complete warranty for repairing.