Industrial End Suction Pumps |
|
We are the leading suppliers of Industrial End Suction Pumps to our clients. These pumps are widely used in various fields including refinery, petrochemical, fire fighting, descaling and water supply. Our wide product range includes RKB Multistage- Multioutlet Pumps, Electrical Submersible Drainage pumps- Modi Industries, KPD-KPDS Process Pumps, Submersible Sewage pumps, Kirloskar End Suction Pumps Type DB, Horizontal Axially Split Casing Pumps, Kirloskar Vertical Multistage Inline Pumps, Kirloskar Solid Handling Non Clog Pumps and Kirloskar - Split Casting Pumps Type – SCT. |
| RKB Multistage - Multioutlet Pumps |  | We offer multistage pumps of type RKB from Kirloskar. These pumps are available in delivery size up to 250 mm with the capacity up to 850 m3/hr and head up to 850m. The pump consists of a number of ring section diffuser casings bolted between suction and delivery casing. We have various models on offer that operate at 1450 rpm and 2900 rpm at 50Hz and 1750 rpm and 3500 rpm at 60 Hz power supply frequency. Specifications of its components are as following:
- Casings: Its latest technique based casing ensures smoothness of hydraulic passages resulting in high efficiency and reliability under hazardous conditions. Its delivery flange is vertical and the suction flange can be oriented left or right viewed from driving end.
- Impellers: It has the enclosed impellers of the radial flow type that are provided with balancing holes to balance the hydraulic axial thrust. Due to this, the rotating elements are statically and dynamically balanced.
- Shaft: Its shaft is made of high tensile steel that is accurately machined and ground is supported by antifriction bearings that take the residual axial thrust and prevent axial float or radial run out. The shaft is protected by shaft sleeve from wear in stuffing box area.
- Stuffing box: Its stuffing box can be sealed by gland packing or by mechanical seal with minor modification. A cooling jacket is provided for the stuffing box while pumping high temperature liquids from 90C to 140C.
- Bearings: the bearings are lubricated using grease. However, oil lubrication is required for temperature above 90C to 140C.
Direction of rotation:
- Standard: Clockwise viewed from driving end
- Optional: Anticlockwise viewed from driving end
- Drive: The pumps offered in this range are suitable for coupling with electric motors, I C engines or steam turbine either directly or through belt drives.
Other specifications:
Flanges:
- Standard: DIN ND – 10, ASA 125, 150 BS 4504-16/11
Optional:
- Suction Flange: DIN ND - 40 or ND – 64
- Delivery Flange: ASA 250, 300 or 800 BS 4504-16/11
Some of the Application areas of our multistage pumps are:
- Sprinkler irrigation
- Fire Fighting
- Water supply to high rise buildings
- Descaling
- Mine dewatering and Boiler feed
| | Send Enquiry |
| Electrical Submersible Drainage pumps- Modi Industries | | We offer our clients a wide range of electrical submersible drainage pumps manufactures by Modi Industries. Apart from standard specifications, we can also supply these pumps in complete stainless steel construction (except elastomeric) as per the requirement of our clients. These can also be equipped with sacrificial Zinc Anodes for maximum life in a saline fluid environment. Our pumps in this range are used as portable electric submersible pumps for corrosive and abrasive applications. We have following models with respective specifications available with us:
Model M-100M/100
- S/M 1.5 HP Outlet 2" Hose
- (BSP/Flange Optional)
Model M-120M
- 2 HP Outlet 2 1/2" Hose
- (BSP/Flange Optional)
We also provide in different series from 1.5 HP to 50 HP.
The design advantages of model M - 100/120 include:
- Built-in ON/OFF thermal switches to protect the motor - M100M/ M120M (For three phase only)
- 410 Stainless Steel Shaft, 304 SS Hardware for maximum corrosion resistance
- 304 SS Strainer (optional)
We can provide our range of pumps in following choice of impeller materials:
- 304 Stainless Steel for sea water and corrosive applications
- 410 Hardened Stainless Steel (HRC 52-55) for abrasive applications
Other Specifications:
- Tungsten Carbide / Tungsten Carbide mechanical outer seal with a secondary inner lip seal
- Seals in wholly enclosed pressure compensated oil chamber
- Field adjustable Nitrile Rubber-moulded Diffuser/Wear Plate to optimize efficiency throughout the life of the pump
| | Send Enquiry |
| KPD-KPDS Process Pumps | 
| Our company offers Kirloskar Process Pumps in KPD, KPD QF types. These pumps are suitable for handling corrosive acids, alkalis, salt solutions, caustics, hydro carbons, oils, thermic fluids, liquefied gases, condensates and viscous liquids.
Our Kirloskar process pumps are available in following specifications:
Range:
- Delivery size up to 200 mm
- Capacity up to 750 m3/hr
- Heads up to 150 meters
- Working Pressures 16-25 kg/cm2
- Temperatures (ñ) 500C to 3500C
Constructional specifications:
- Pumps are as per DIN 24256 and ISO 2858 and generally conform to API 610 (7th Edition)
- Design: back pull out type
- Various available models to operate at 1450 rpm and 2900 rpm at 50Hz and 1750 rpm and 3500 rpm at 60 Hz
- Casing: The casing has axial suction and top centre line delivery. Smooth hydraulic passages ensure high efficiency. Normal design is for foot mounted pumps. Centre line mounting for special applications are also available.
- Impeller: Enclosed type and semi-open impellers as per requirement. Hydraulic balancing of impellers is achieved either by back vanes or by balancing holes. The impellers are statically and dynamically balanced. Reliable fixing of the impeller on shaft is achieved by using helicoil insert under impeller nut. Inducer can be supplied to improve NPSH performance,.
- Shaft: Two antifriction bearings support the shaft to take residual axial thrust and prevent axial float or radial run out. It is fully protected from the liquid handled by means of a shaft sleeve and PTFE gaskets between impeller nut, impeller hub and shaft sleeve.
- Stuffing box: It is sealed by gland packing or by mechanical seal. By changing some standardized parts, conversion from gland packing to mechanical seal is done. Re-machining of stuffing box is not necessary. Stuffing box cooling is provided for operating temperature 105 0C for gland packed and 140 0C for mechanical seal fitted pumps.
- Bearings: The bearings are oil lubricated. Bearing oil cooling arrangement is provided for high temperature (above 1800) application. All pumps are provided with reinforced bearing arrangement as standard supply.
- Direction of rotation: Clockwise viewed from driving end
- Drive: Pumps can be driven by electric motor or engine
Flanges:
- ANSI B 16.1, CL 125 Flat Face: for CI/BR
- ANSI B 16.5, CL 150 Raised Face - for sp. Metals such as stainless steel and cast steel
- Drilling as per DIN, ASA, BS (Optional)
Applications:
- Chemical Process Industries
- Petrochemical
- Nuclear
- Refinery
- Paper and Power Plants
| | Send Enquiry |
| Submersible Sewage pumps |
| Our company deals in submersible sewage pumps manufactured by Kirloskar. These pumps are available in delivery size up to 300 mm with the capacity up to 1800m3 /hr (Maximum) and Head up to 90m (Maximum). The maximum permissible sold size is up to 300 mm.
Our range of submersible sewage pumps finds application in following areas:
- Screened sewage
- Raw sewage
- Contaminated effluents
- Industrial waste water
- Storm water
- Trench and Tunnel water
- Drain water, Mine water etc.
Our submersible sewage pumps of type–NS are offered with following specifications:
- Constructional Specifications:
- Single stage, single suction pumps with overhung non-clogging impeller
- Pumps offered in stationary as well as transportable arrangements
- The stationary arrangement is supplied with pump connector unit
- The connector unit is connected to pump support bracket with rubber diaphragm to make it leak proof joint
Pump Casing:
- The radially split casing is provided with integrated delivery nozzle cast
- Suction is axial and delivery nozzle is central and horizontal
- Specially designed semi-concentric casing that reduces radial thrust and ensures vibration-free performance
- Wide volute passage ensures non-clogging operation of the pump
Impeller:
- These are of non-clog type that allows smooth passage of solids
- Offered with single or multi vanes in semi-open, enclosed, or free flow designs to cater to wide applications
Shaft:
- High tensile steel shaft is accurately machined and its ground is supported by two ball bearings in the motor above the impeller
- Designed to transmit the power without undue vibrations and deflections
- It is common for pump and motor of monoblock design
Mechanical Seals:
- Two mechanical seals in tandem arrangement are provided to ensure no ingress of water or sewage in motor
Bearings
- Bearings are grease lubricated and sealed for life, hence maintenance free
- Direction of Rotation: Clockwise when viewed from motor top
Drive:
- Motor is dry type submersible and cooled by liquid being handled
- Motors are air tested for leak-free operation
- Degree of protection for motor is IP68 as per IS:2147
- Class of insulation : F
- Voltage : 415V /- 10%
- Frequency : 50 Hz. /- 5%
- Type of starting : As per requirement (DOL/Star Delta/ATS)
| | Send Enquiry |
| Kirloskar End Suction Pumps Type DB |
| We supply and export a wide range of Kirloskar end suction pumps in DB type. These are centrifugal pumps available in delivery size range of up to 150 mm with the capacity of up to 550 m3 / hr and having heads up to 100 meters. These end suction pumps are suitable for circulation of water in various industrial application like air-conditioning plant, power station, mine drainage, lift irrigation, sprinkler systems, fire fighting, booster service, pumping brine, alkaline solutions, oils, benzene and others. It works for liquids having temperature in the range of -100 to 1000 C.
Constructional Specifications:
- Available in single stage, single suction, and horizontal shaft type
- Made in accordance with DIN 24255
- Models are available to operate at 1450 rpm and 2900 rpm at 50 Hz and 1750 rpm and 3500 rpm at 60 Hz
Material of Construction:
- Pump Casing and Casing cover: C.I. / Bronze / Ph.Br.
- Impeller: C.I. / Bronze / Ph.Br.
- Shaft: Carbon Steel / St. Steel
| | Send Enquiry |
| Horizontal Axially Split Casing Pumps |
| Our company offers a wide rang of horizontal axially split casing pumps in UP, UPL and UPH types. These pumps are available in delivery size up to 1220 mm with the capacity up to 24,000 m/hr and head up to 180 meters.
These pumps are used in following applications:
- For handling water with slight industrial impurities
- Water Works
- Storm Water
- Irrigation
- Sprinkler Irrigation
- Fire-fighting
- Air Conditioning
- Water Circulation
- Waste Water Treatment
- Processing
- Power
- Fertilizer
- Refinery
- Paper
- Sugar and Textile Mills
Constructional Features: Our pumps in this range are offered in horizontal axially split casing, single stage, double suction or single suction, single volute or double volute type with horizontal shaft.
Special Features:
- Bottom suction branch
- Rotating assembly accessible for inspection or maintenance by removing upper half casing without disturbing suction and delivery piping and motor
- Horizontal execution in standard specification
- Vertical execution in optional specification
- Vertical pump, direct drive or with universal shaft arrangement
- High hydraulic and overall efficiency due to superior design and manufacturing techniques
- Good suction performance and low NPSH
- Stable characteristics
- Low maintenance required
- Vibration free performance
- High reliability
Specifications of components:
- Pump Casing: Horizontal axially spilt volute type, suction and discharge nozzles and supporting feet are cast integral with lower half casing
- Impeller: Double or single suction type accurately balanced. In case of double suction impellers, the hydraulic thrust is balanced automatically because of pressure equalization on both sides of the impeller
- Shafts: The high tensile steel shaft accurately machined and ground is supported by antifriction bearings. The shaft is protected by shaft sleeves from wear in stuffing box area.
- Stuffing Box: Can be sealed by gland packing or by mechanical seal and is suitable for liquids having temperature up to 90C
- Bearings: Grease Lubricated deep groove ball / roller bearings are provided. Large pumps can be provided with Oil Lubricated/ Oil ring bearings.
Direction of Rotation:
- Standard: Anticlockwise (ACW) when viewed from driving end
- oOptional: Clockwise (CW) when viewed from driving end
- Drive: Suitable for coupling with electric motors, engines or steam turbines either directly or through belt drives, gear boxes etc.
Flanges:
- Standard: Drilled to BS:10 Table D/E/F or BS-4504, Table PN16 plain face depending upon model.
- Optional: DIN /ASA with suitable pressure rating depending upon model.
| | Send Enquiry |
| Kirloskar Vertical Multistage Inline Pumps |
| We offer Kirloskar vertical multistage inline pumps that are vertical multistage, high pressure centrifugal pumps in ring section design with inline suction and delivery. Its inline suction and discharge casing ensure easy installation and simple piping layout and negligible effect of outside nozzle forces/moments.
Some salient features of these inline pumps are as following:
- Durable and light parts of high quality materials like stainless steel, tungsten carbide and ceramic
- Energy efficient through superior hydraulic design and ultra smooth hydraulic passage
- Power saving of 10% to 30% when compared with conventional pumps
- All sealing by means of O-rings
Specifications of components of the pump are as following:
- Impellers: These are made of pressed stainless steel, enclosed and radial flow having ultra smooth hydraulic passages resulting in higher efficiency. These impellers have superior suction eye design ensuring lower NPSH.
- Diffusers: Diffusers are made in pressed stainless steel and designed to reduce the internal losses.
- Outer Casing Cover: Outer casing cover has specially shaped O ring grooves for optional sealing. Pressurised water between diffuser and outer casing dampens the noise to ensure quiet operation.
- Shaft: Bush bearing support high tensile stainless steel vertical shaft that is sealed with mechanical seal of DIN 24960 standard.
- Bearings: Radial type bush bearings of tungsten carbide on shaft and ceramic bearing in diffuser. These are maintenance free, self lubricated and highly wear resistant. Axial thrust is taken by motor bearings.
- Direction of Rotation: Clockwise viewed from driving end.
Flanges: Flanges are in DIN standard. Material of Construction 01 and 02
- Oval: 25 IL, 32 IL, 40 IL pumps up to 15 stages are supplied with oval flanges as a standard.
- Round: 25IL, 32IL and 40 IL above 15 stages 50IL, 65IL, 80IL and 100IL pumps in all stages.
- Material of Construction 03: Round flanges are supplied for all pumps.
Applications:
Liquid temperature from 150c to 1200c
Building industry
- Booster
- Fire fighting
- Hydro pneumatic system
- Heating
- Ventilation
- Air conditioning
Small capacity power plant
- Boiler feed
- Condensate transfer
Water treatment plants
Chemical, Pharma, Textile
- Cooling
- Transfer
- Hot water services
Engineering and Automobile:
- Industrial washing machines
- Coolant circulation
Dairy, Food processing, Beverages
- Clean water services
- Pressurised cleaning systems
- Irrigation
Sprinkler irrigation
- Golf course
- Parks
- Gardens
- Sports grounds
Water Supply
- Pressure boosting systems
- Hotels
- Resorts
| | Send Enquiry |
| Kirloskar Solid Handling Non Clog Pumps |
| Our company supplies a wide range of solid handling non clog pumps in types of SHM, SHS and SHV manufactured by Kirloskar. These pumps are available in delivery size up to 200 mm with the capacity up to 800 m3/hr and head up to 90 m. These can be offered in maximum permissible solid size up to 105 mm as per the model with standard consistency up to 5% and QP impellers for more than 5% consistency.
Applications:
- For handling liquids with solids in suspension
- Sludge or pulpy material in paper Industries
- Sewage or waste with soft solids in suspension
- Viscous liquids or liquids carrying fibrous material or powdered material slurries
- Contaminated process liquids like sugar factory waste
- Trade liquors
- Water carrying gravel
Constructional Features:
- SHM are horizontal non clog pumps having single stage, single suction with back pull out type design
- SHS are vertical non-clog pumps for wet pit applications
- The pump unit is suspended by a column pipe that also protects the transmission shaft
- Our pumps in this range can be offered with a column length up to 6.5 m.
- SHV are vertical non clog pumps for dry pit application in vertical orientation to be driven by vertical flange mounted motor that is directly coupled
- SHVT pumps are vertical non clog pumps for dry pit application in vertical orientation to be driven by vertical flange mounted motor but coupled through transmission shafting
- The pumps operate at 50 Hz and 60 Hz
Specifications of the components of the pump are as following:
- Casing: End suction with top centre line delivery as well as horizontal side delivery. High efficiency volute providing smooth unobstructed flow. Delivery flange and feet are cast integral with the casing. A large inspection opening is provided on casing with easily removable cover.
- Impeller: Single suction type non clog impeller dynamically balanced. Enclosed or semi-open impellers are available in code N, P, Q or R.
- Shaft: In SHM pumps, four driving units cover the entire range. Shaft is supported by two bearings. Shaft in stuffing box area is protected by a shaft sleeve. Axial clearance between semi-open impeller and suction wear plate can be adjusted externally without dismantling the pump. The shaft sleeves under bearing housing and bearing spider are shrunk fitted to shaft in SHS pumps.
- Stuffing Box: Standard stuffing box is gland packed with grease sealing. Without cooling up to 90 0C and with cooling up to 140 0C. Mechanical seal option is also available.
Bearings for SHM Pumps
Standard: Deep groove ball bearings at DE/NDE.
Optional:
- Deep groove ball bearing at DE and roller bearing at NDE.
- A pair of angular contact ball bearings (BECB) at DE & one cylindrical roller bearing at NDE.
- Standard lubrication is grease and optional is oil.
Bearing for SHS Pumps: Intermediate shaft bearing is rubber (For water Lubrication) and bronze bearing (For grease lubrication). Thrust ball bearing in combination with metallic journal bearing at head shaft. Transmission bearings are lubricated with external clear water or grease.
Thrust bearings are grease lubricated.
- Direction of Rotation: Clockwise viewed from driving end
- Drive: These pumps are suitable for coupling with electric motor or engine directly or through belt drives
Flanges:
- Standard: drilling to DIN 2533 ND 16
- Optional: drilling to ASA/BS/IS
| | Send Enquiry |
| Kirloskar - Split Casting Pumps Type - SCT |
| We offer our clients a wide range of horizontal axially split casting pumps manufactured by Kirloskar. These pumps are available in delivery size up to 250 mm with the capacity up to 1100 m3/hr and head up to 115 meters.
Application:
- Suitable for handling water with slight impurities in Industries
- Water Works
- Irrigation
- Sprinkler Irrigation
- Fire-fighting
- Air Conditioning Plants
- Water Circulation
- Processing Plants
Constructional features:
- Horizontal axially split casing, Single stage, Double suction or single suction pumps with horizontal shaft and detachable stuffing box called Insert
- Variety of models are available to operate to 50Hz and at 60 Hz
Some special features of these horizontal axially split casting pumps are:
- Direct or gear drive
- Suitable for higher working pressures
- Rotating assembly for inspection or maintenance by removing only upper half casing without changing suction and delivery piping and motor
- Pump axis horizontal or vertical
- Vertical pump, direct drive or with universal shaft arrangement
- Latest design and manufacturing techniques give highest hydraulic and overall efficiency
- Very high efficiency in the operating range
- Good suction performance and low NPSH
- Stable characteristics
- Low maintenance
- Vibration free performance
- High reliability
- High degree of interchangeability of components
Specifications of the components of our pumps are as following:
- Casing: The casing is horizontal axially split volute type, suction and discharge nozzles and supporting feet are cast integral with lower half casing.
- Impeller: Its impeller is double or single suction type that is accurately balanced. In the case of double suction impellers, the hydraulic thrust is balanced automatically due to pressure equalization on both sides of the impeller.
- Shaft: The high tensile steel shaft is accurately machined and ground is supported by antifriction bearings. It is protected by shaft sleeves from wear in stuffing box area.
- Stuffing box: The stuffing box can be sealed by gland packing or by mechanical seal and is suitable for liquids having temperature from (-) 8 0C to 90 0C. Packing or mechanical seal can be offered upto 120 0C in special cases.
- Bearings: Our pumps are provided with deep groove ball bearings. These are lubricated using grease.
Direction of rotation:
- Standard: Clockwise viewed from driving end
- Optional: Anticlockwise viewed from driving end
- Drive: The drive is suitable for coupling with electric motors, I.C. engines or steam turbines either directly or through belt drives.
Flanges:
- Standard: Drilled to BS: 4504 PN 16 F. F.
- Optional: DIN 2533, ND16, BS 4504, PN 25 ASA 125/150
| | Send Enquiry |
|
|
© Vijay Engineering & Machinery Co. All Rights Reserved (Terms of Use)