Vinko Auto Industries Limited

Features: 1. Permanent Matched Set. 2. No lateral whip, spin or jump-off. 3. Deep pulley grooves are not required even on horizontal drives. 4. Heat and Oil resistant.

Features:
1. Permanent Matched Set.
2. No lateral whip, spin or jump-off.
3. Deep pulley grooves are not required even on horizontal drives.
4. Heat and Oil resistant.
Construction
1. Tie-band.
2. Rubber impregnated cross woven cotton-polyester fabric.
3. Cushion rubber.
4. Low Stretch high modulous adhesive activated polyester cable cord.
5. Compression rubber.

Features * Designed specially for reverse-bend drive by positioning tensile members closer to the bottom compare to that of conventional multiple V-belts A, B, & C. * Particularly suitable to Agricultural Machinery such as combined harvester and garden tiller where belts are often driven with tension idler pulley on their back.

Features * Designed specially for reverse-bend serpentine drive. * New cross section for maintaining proper belt position in pulley groove even in case of extreme reverse-bend drive. * Owing to larger flexibility gien by as well as to NEW CROSS Section, the service life has become longer than that of traditional double V-belts.

F.H.P. V-Belts Alaska F.H.P. V-belts are built for maximum tension control, drive uniformity and long life, with minimum heat build-up and stretching on low horse power electric motors and gasoline engines. They are designed for high speed drive and short center distance. Classical V-Belts For classical drives, high speed and high torque drive on light or heavy industrial or automotive machinery. Alaska classical V-belts have exceptional length stability and drive uniformity.

Features: * High power rating. Requires about 33% of the space needed by classical V-belt drive. * Long Life. * High efficiency. * Heat and oil resistant. Belts are anti-static. * Length Stability. A matched set of Alaska Wedge. V-belts for multiple drive retains superior uniformity undertension. A Alaska matched set remains perfectly matchedeven after long period of storage.

* The use of smaller, less costly sheaves. * Smoother, vibration free performance. * High speed capability. * Space-saving, compact design. * Higher efficiency than conventional V-belts. * Speed ratios up to 40 to 1. * The use of small backside idlers. * Serpentine drive design capability. * Shorter centre distance drives. * Moulded belt with ground rib performance.

Features: * High power rating.Requires about 50% of the space needed by classical V-belt drive. * Long Life. * High efficiency. * Heat and oil resistant. Belts are anti-static. * Length Stability. A matched set of Alaska Wedge. V-belts for multiple drive retains superior uniformity undertension. A Alaska matched set remains perfectly matched even after long period of storage.

Flexible Radiator Hose designed to replace straight or curved hoses. The benefit is maximum coverage with minimum Inventory Hose inside diameter remains constant from end to end allowing free coolant flow. High abrasion & Heat resistant, Synthetic Rubber (EPDM) cover and tube. Extra strength knit ply reinforcement with helical steel wire spiral molded between tubes and cover provides collapse and kick resistance. Engineered to resist electrochemical degradation the leading cause of hose failure. Meets SAE 20 R 5 Class D-2 specifications. TEMPERATURE RANGE:- -40 F to 257 F (-40 C to 125 C) CAUTION :- Do not use for fuel or oil transfer applications.

Covers a wide range of light and heavy truck applications. Synthetic rubber (EPDM) construction Multiple-ply woven hose. Meets SAE J20e, Type 20R1, Class B Tube, Class C Cover, Standard wall construction. Available in 0.9M lengths. Range from I.D. 25.4mm to 101.6mm. Temperature Range : +40 F to +260 F (-40 C to +125 C)

Alaska moulded Radiator Hoses are pre-shaped designed to replace O.E.M. Hose. Knitted reinforcement and all synthetic rubber (EPDM) construction give shigh strength and resistance to heat and all recommended coolants. Engineered to resist electrochemical degradation the leading cause of hose failure. Meets SAE 20 R4 and 20 R3 Type Ee class D-1 to D-2 specifications.

Tube & cover constructed with synthetic rubber (epdm) compound with spiral reinforcement for high burst strength and good heat resistant for general service on most cars. Meet performance requirements of sae 20r3 class d-2, range from i. D. 6. 4mm to 25. 4mm. 6 meter to 15 meter length. temperature range:- -40? F to 260? F (-40? C to 125? C)

Covers a wide range of passenger car and light weight truck applications. Synthetic rubber (EPDM) construction reinforced with a ply of rayon knit cord. Meets performance requirements of SAE J20e, Type 20R4, Class D-2 requirements. All in 0.9M lengths. Range from I.D. 19.5mm to 101.6mm. Temperature Range : -40F to +26 F (-40 C to +125C)

Covers a wide range of Passenger Car, Truck, Stationary, Engines, Industrrial and home applications, Synthetic Rubber (EPDM) construction reinforced with a ply o knit cord. Meets SAE-J2-R1 class D-2 requirements available. TEMPERATURE RANGE:- -40 F to 257 F (-40 C to 125 C) for excellent burst strength. CAUTION :- Do not use for fuel or oil transfer applications.

Multi purpose hose for use of fuel line. PEV and EEC systems and for fuel return hose connections on Fuel injection systems. Approval for use with Gasoline, Diesel and Gasoline blends of ethanol, methanol and ethers. The Oil and Gasoline resistant Nitrile rubber cover withstands exposure to Fuel, Vapor, Heat and moisture. The Rubber tube, specifially compounded to resist Gasoline, oil, Diesel and other Fuels. Meets SAE 30 R 6 and 30 R 7.

This fuel injection hose is designed specially for auto and truck fuel injection system in synthetic rubber (epdm). This handle the higher pressure, temperatures and chemical problems produced by todays smaller, hotter running fuel injected engines safely and efficiently. Fluoro elastomer inner tube provides exceptional resistance to oxidised petrol, diesel fuel, bio decret plus methanol and ethanol additives that weaken normal fuel hose. A special braid reinforcement handles pressures to 225 psi, provides burst strength in excess of 900 psi. An abrasion resistant outer cover resists temperature extremes -30f to +300f (-34. 5 c to +149 c) as well as oil grease, ozone and coolants. Meets sae j30c, type 30r9 requirements. Range from : 6. 4mm to 9. 5mm i. D. Length upto 25 meter.

Are pre-shaped designed to replace O.E.M. Hose. Knitted reinforcement and synthetic rubber (EPDM) construction give high strength and resistance to heat and all recommended coolants. Engineered to resist electrochemical degradation the leading cause of hose failure. Meets SAE 20 R4 and 20 R3 Type Ee class D-1 to D-2. Temperature Range : +40 F to 260 F (-40 C to +125 C)

Synthetic rubber tube and cover designed to handle transmission oil coolers for auto and light truck and also used for power steering systems and resists oil, ozone and heat aging. Range from I.D. 7.9mm to 12.7mm. Length upto 10 meter. Temperature upto +275 F (+125 C).

The high temperature rated strong heater hose resist the effects of heat and electrochemical degradation. It is made with EPDM rubber and reinforced with heat resistant and extra long service life. Meets SAE 20R3 Class D-2. TEMPERATURE RANGE:- -40 F to 257 F (-40 C to 125 C) CAUTION :- Do not use for fuel or oil transfer applications.

Heavy duty heater hose requires higher heat resistant and higher temperature. Synthetic rubber (EPDM) compound with a spiral reinforcement. Excellent burst strength, heat resistant. Special insulation compound minimises heat loss. Meets performance requirements of sae 20r3 class d-2, range from : i. D. 6. 4mm to 25. 4mm. Length 6 meters to 15 meters. temperature: -40 f to 300f (-40 c to +149c)

Features: Variable speed V-belts, also termed V / S - belts, are temperature and oil resistant as well as anti-static. A special rubber compound with textile fibres oriented across the length of the belt provides high stability and minimizes deflection in the cross section. The moulded cog ensures maximum flexibility and optimum fit in the pulley grooves. The cord, the power transmitting element, has been designed for heavy power transmission while at the same time ensuring a very high degree of length stability. Special belts are produced to order, e.g.with Aramid cord .

Features: * Designed specifically to handle the "wear and tear" of clutching applications. Bias cut, cross woven fabric is oil and heat resistant. * Tensile cords transmit up to 20% more horsepower than traditional polyster construction. High modulous cords placed just above the neutral axis resist elongation, reducing or eliminating retensioning or expensive take-up mechanisms. * Formulated to reduce heat buildup for a cooler running, longer lasting belt. The compound used balances firmness with flexibility to maintain cross sectional uniformity.

Alaska Bonding Gum is having good adhesion & better storage stability properties. Available to suit 99C and 150C temperature processes.

Nitrile rubber tube & cover connects vehicle filler neck to tank on passenger cars, light trucks, boats, as well as auxiliary fuel tanks on rv's. Handles leaded, unleaded petrol and diesel fuel. Rugged double reinforced construction helps prevent collapse. Meets sae j30, r7, and sae j1527, type b2. Range from i. D. 19mm to 76mm. Length upto 10 meter. Temperature range : -30C to +100C.

Multipurpose fuel hose being used as a fuel line on all types of petrol engines, diesel fuel, gasoline blends of ethanol. Excellent resistance to oil, petrol, grease and weather. Synthetic rubber (EPDM) construction reinforced with a single ply of braided cord, neoprene cover, nitrile tube. Meets sae J30C, type 30r7 requirements. Range from 3. 2mm to 19mm I. D. Length upto 76 meter. temperature range : -40 c to +125 c

Features : * Cut edge moulded cogged V-belts have a precision cogged profile base which is designed for uniform stress distribution and superior heat dissipation. * Their construction permits greater flexibility and a higher kilowatt capacity for exceptional performance on small diameter pulleys using FHP, Classical, Wedge and Narrow section drives. * The robust construction is specially designed to fit the pulley grooves exactly, which allows maximum wedging action. * The belts are built with low stretch-high modulous stiff polyester tensile members to resist fatigue and shock loads. The cord and polychloroprene rubber are bonded to prevent separation and reinforcement layers on both sides of the tensile member improve cord stability. All belts are oil & heat resistant and static conducting.

1. Rubber impregnated cover cotton polyester fabric. 2. Low stretch high modulous adhesive activated polyester cable cord. 3. Cushion Rubber.

Resists oil, grease, and heat deterioration is to be used synthetic rubber (EPDM) tubing. Retains flexibility at low temperatures. Meets SAE J1037 Material Spec. Range from 2.8mm to 9.5mm I.D. Length upto 15 meter. Temperature : -40C to +125C.