The AMF Controller Module is a microcontroller based technology & is fully programmable at the site. It is totally different from mechanical/electro mechanical based AMF panels. It has a user-friendly man-machine interface with the help of a keypad, LED’s and a LCD display. Since, all messages are displayed on LCD, all the messages are in clear user friendly language.

Features

• Complete AMF logic: Auto, Manual & OFF, with additional PROGRAM Mode.
• Built in Line Voltage Monitor: LVM sensing the three phase supply for operation in safe limits.
• Generator Voltage Monitor: GVM, load is transferred to Genset only if running at the correct voltage.
• Built in timers: Mains Wait, Cranking Wait, Cranking ON, Cranking OFF, Cranking Attempts, Stop Solenoid, Engine Idle Run Timers are built in and fully adjustable by the user.
• Built in Engine Safety: Low Oil pressure, High Coolant temperature, V Belt failure, and Start failure.
• While the Mains or Generator is ON, different vital parameters are displayed on the screen. Each section of parameter screen changes after 10 seconds. If any parameter screen is meant to be 'freezed', it can be done by HOLD/RELEASE button, indicated with a ’HOLD’ LED. This LED is ON, when parameter screen is ’freezed’ and vice versa.
• The following parameter screens are displayed, when LOAD is ON:
  
  • Load ON Mains (or Load ON Gen)
  • Average Phase to Phase Voltage, with RY, YB and BR voltages.
  • Average Phase to Neutral Voltage, with RN, YN and BN voltages.
  • Average Current, with current on R phase
  • Average Current, with current on Y phase.
  • Average Current, with current on B phase.
  • Average KVA, with KVA load on R phase.
  • Average KVA, with KVA load on Y phase.
  • Average KVA, with KVA load on B phase.
  • Frequency (in Hz), with RPM (for Generator only)

Description

The main function of the AMF panel is to start the generator in case of mains failure. It ensures quick resumption of power supply without any attendant. Load is transferred from mains to the generator. Therefore there is no need to transfer the load by means of changeover switch. AMF resumes the supply in just a few seconds in case of mains failure.

Besides ensuring automatic resumption of power supply, the panel also provides many vital protections to the generator such as engine shut off at Low Lubrication Oil Pressure., Over Load, Over Speed, etc. Panel will not only switch off the generator but it will give an audio visual warning to call the attendant.

General Features

• All Waders AMF panels are equipped with microcontroller based Waders AMF Controller HJ110. Hence, all the features of HJ 110 are available to the AMF panel. (Kindly refer to details of our AMF Controller Module HJ-110).
• Panels can be made as per customized requirements.
• Single or dual generators control available, in customized panels.
• Multiple Fault Protection like LLOP, HCT, etc.
• Automatic battery charging system
• Generator supply within seconds
• Auto change over from generator to mains in milliseconds.
• Auto stop for generator
• Time Delay to ensure smooth power resumption
• Auto start on mains failure.
• Models 2 KVA to 1250 KVA
• One year warranty

Other panels like Automatic Synchronizing Panels, Power Factor Corrector Panels, Fire Fighting Panels, Motor Starter Panels, Standard Generator Panels, Busbar Ducts, Distribution Panels, etc. are also available.

Our engine safety units are microcontroller based and give protection against Low Lubricant Oil Pressure (LLOP) and High Cylinder Temperature (HCT) to the engine. This compact unit controls the entire operation of the engine and continuously displays various engine activities. The Engine Safety Unit (ESU) can be directly mounted with rubber pads on engine. There are two types of engine safety units available with us and they are Engine Safety Units - ESU-110.

This device is helpful in continuous monitoring of frequency of the input supply. If in case the frequency changes from the set limit, It energizes the electromagnetic relay. This type of safety relay is useful in generator control panels, frequency sensitive equipments, etc. This unit also protects any electrical load from over loading. Various types of programmable electrical protection we manufacture are Over / Under Voltage Relay - OUV-110, Over / Under Frequency Relay - OUF-110, Engine Start Relay, Over Current Relay, Earth Fault Relay.

• Panels provide complete automation needed for the parallel operation (synchronization) of two or more generators.
• Automatic and Manual Synchronizing Mode available
• All the synchronizing relays are microcontroller based and are fully programmable at site.
• AMF section is controlled by the microcontroller based Waders AMF Controller HJ 110. Hence, all the features of HJ110 are available to the AMF section of the panel.
• Panels can be made as per customized requirements.
  vi) Multiple fault protection.
• Capacity - 2 KVA to 1250 KVA

Other panels like Automatic Mains Failure (AMF) Panels, Power Factor Corrector Panels, Fire Fighting Panels, Motor Starter Panels, Standard Generator Panels, Busbar Ducts, Distribution Panels, etc. are also available.

The name itself describes the product; it is used control exhaust fans of canopy. This device helps in checking the status and display information regarding generator or voltage and other activities. We manufacture three types of models which are suitable for single phase fan dual and three phase fans. The models are canopy Exhaust Fan Controller - CET-110 DF, Canopy Exhaust Fan Controller - CET-110 TP, Canopy Exhaust Fan Controller - CET-110 SP.

Features

• All parameters are displayed on seven segment hi-bright red displays
• The canopy exhaust fan is switched on after 30 seconds, after the generator is turned on
• The fan remains on as long as the generator runs
• The generator voltage is displayed, in single fan models
• The exhaust runs for 15 minutes, when the mains supply is restored
• All the timers are digitally displayed in countdown format
• All the mentioned timings are factory set, and can be changed at the time of order
• The fan will remain off, as long as the generator is not operational
• The models available for single or three phase fans
• Controls all single or three phase fans, up to 3 H.P.

Digital programmable Time Switches are specially designed for controlling the operating time of general electrical loads. It is a fully automatic device which finds application in both domestic as well as industrial fields. It is widely used to control the operation of common domestic loads such as Porch Lights, Gate Lights, Garden Lights etc. and industrial loads such as Advertisement Hoardings, Glow Sign Boards, Neon Sign Boards, Commercial Lighting, Street Lights etc. The large display of the device doubles its utility as a digital clock also. The sturdy and aesthetic enclosure suits well into any kind of environment. The unit is extremely user friendly and easy to install.

Features

• Automate lights and equipments
  Control operating time (set ontime and off time)
• Save Energy
• Reduce Power Bills
• Flexible Time Configuration
• Upto 1 minute resolution
• 12/24 hour formats
• Secondary use as digital clock
• Available in 5 amps and 25 amps models
• 2 years Battery backup for RTC

Models

• CLK 110 (1 On-Off session/24Hr)
• TCS 110 (16 On-Off session/24Hr)
• TCS 110-X (64 On-Off session/24Hr)
• WPT 110 (5 On-Off session/ 7 days of week)

A complete microprocessor based solution to restrict generator supply automatically for the places where single generator supply is provided to many users as in multistoried apartments, commercial complexes, multiplexes etc.

Features
An advantageous and cost effective alternative to the conventional manual changeovers.
No restriction on choice of generator power points.
No separate wiring is required for generator supply.
Assured availability of allotted power on generator supply.
Failsafe, tamper proof and maintenance free.
Indications for all operating states.
Simplifies electrical wiring and complexity

Functions
i) The unit provides an uninterrupted supply to the user, on mains.

ii) Displays parameters like voltage, current, timers, etc. in 4-digits display or by LCD, depending on the model.

iii) It provides auto change over from mains to generator & vice-versa.

iv) While providing generator power, unit monitors allocated load (say 1000 W) to the user. If the user increases the load beyond the set limit (factory adjusted), the power to that particular user is interrupted for 10 seconds.

v) Generator supply is again restored after 10 seconds to check, whether the user has switched off the excessive load or else power is again interrupted.

vi) Once, the load is reduced to the limit (say 1000 W), user gets an uninterrupted generator supply.

vii) On resumption of mains supply, the unit checks the stability of incoming supply for 5 seconds and after that the load is shifted automatically to the mains supply.

viii) Models available in single phase and three phase, ranging from 0.5 A to 50 A. Systems up to 1200 KVA can be provided as per user demand.

ix) Model also available (K series only) for recording Kilo Watt Hour (KWH) reading, for generator.

We are engaged in manufacture and export of Programmable Temperature Controller which is based on a single chip microcontroller that turns on & off an auxiliary relay on temperature settings. It includes a seven segment, bright red display that displays temperature with precision of 0.1 C. The program mode allows setting temperature within a given range. The relay ‘ON’ timing can be set along with threshold temperature, where the relay turns OFF, again.

An ideal and economical solution to control single/three phase Submersible Pumps. It has an in-built water level controller.

Features
i) The complete operation of submersible pump is controlled by this compact unit.
ii) Parameters and process status like voltage, current, overload, dry, pump On, Full, etc. are continuously displayed.
iii) Easy to control auto and manual mode
iv) The unit digitally displays incoming voltage and current, while the pump is running.
v) Auto cutoff for Start signal.
vi) Programmable Over Load Protection for pump.
vii) Models available with or without Running & Starting Capacitors.

Digital Water Level Controller

A stand alone water level controller, added to the existing water pump and panel, to provide complete automation to the pump.

Features

i) The foremost purpose of the system is to make the user free of all his daily water filling requirements.
ii) Easy to control auto and manual mode.
iii) No chance of dry running or over flowing.
iv) Ideal for dual tank and storage tank systems.
v) Different processes like ’DRI’, ’P On’, ’FULL’, etc. are displayed through hi-red display.
vi) Rugged & aesthetic design suits well to nearly any environment.
vii) Models available for single and three phase pumps.

The main feature of this controller is that it ELIMINATES ALL THE ENGINE GAUGES AND ELECTRICAL METERS. In short, there is no moving coil meter in the generator system, neither for the electrical parameter nor for the engine.
It is a unique controller that provides all the standard electrical meters, along with engine meters for Cylinder Temperature, Oil Temperature, Oil Pressure, RPM, Hours, Battery Charger etc. in a single controller panel. The Controller SAP-110 is a state of the art; micro controller based technology, and provides total control to the user.

Features

i) The SAP110 is suitable for 2KVA to 1250KVA generators.

ii) The SAP-110 controller provides all the standard metering related to the generator, along with the standard engine gauges for Oil Pressure, Oil Temperature, Cylinder Temperature, Fuel Level, Battery Charger, RPM, Hour Meter, etc.

iii) All the parameter description is provided on 104 mm x 35 mm LCD screen.

iv) The Key Switch is provided on the panel to start and stop the generator.

v) The Engine Gauges are displayed on the LCD, in a graphical presentation.

vi) It uses existing engine gauge sensors like temperature, pressure, etc. to display the engine’s cylinder temperature, oil Temperature, pressure, etc.

vii) Basic safeties for LLOP, HCT and V-Belt Failure are provided.

viii) Parameters Displayed:
a. Average Phase to Phase Voltage, with RY, YB and BR voltages.
b. Average Phase to Neutral Voltage, with RN, YN and BN voltages.
c. Average Current, with current on separate phase
d. Average KVA, with KVA load on separate phase
e. Frequency (in Hz), with RPM.
f. Oil Temperature (in Bar Graph)
g. Cylinder Temperature (in Bar Graph)
h. Oil Pressure (in Bar Graph)
i. Fuel Level (in Bar Graph)
k. Battery Level (in Bar Graph)
l. Engine Running Hours

ix) Display starts blinking, with audio warning, if any gauge, exceeds or decreases to ’RED’ mark (as in conventional gauges).

An ultimate pump controlling system, the product is microprocessor based and includes an in-built Water Level Controller. It is compact in size and handles (controls & manages) the entire array of operations of submersible pump.

Features

• 35 ON-OFF programmable sessions for one week

• Programmable protections against Over/Under Voltage, Over Current, Single Phasing, dry running, etc.

• Run Time Compensation mode gives a facility to compensate the running time of pump, in case of power supply failure during preset pump running time

• The unit is equipped with a LCD display, which displays supply voltages, pump current, clock, current timing of the pump operations, time left for current session

• There is a manual mode operation to start & stop the pump manually in case of any emergency

• The system uses separate PCON-110 and VCS-110, to provide complete pump management

• The device based on microcontroller logic allows both type of automatic operation of pump i.e. An automation through programmable time settings, to operate the pump according to the clock hours or as per the running duration of the pump

• The system has also the facility to operate the pump automatically by monitoring water level in the over head tank

• The device has various protections for the pump i.e. dry running protection, over current, over load, single & reverse phasing protection, under and over voltage protection etc.

• The system is equipped with a battery backup system for approximate 2 years.