ADT Industries

• Reebaklens RR is used as a rust remover from steel bars prior to encasing in concrete / microconcrete. It can also be used on ohter steel surfaces prior to coating with epoxy systems.

• Rapid Action: Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action. Penetrates oil and grease.

• Reebaklens RR cleaning agent is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear green solution.

• Fosroc provides a technical advisory service to specifiers, end-users and contractors as well as on-site technical assistance in locations all over the country.

• For rusted metal (iron base): Apply Reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.
• Removal of rust and mill scale: Prewet the floors, then using a stiff bristle broom, brush the affected areas with a solution of Reebaklens RR cleaning agent and water. Strength of the solution required will vary but should be between 1 : 1 and 1 : 4 (Reebaklens RR cleaning agent to water) When the action has finished, wash down thoroughly with clean water. Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water. Repeat if necessary. High degree of rust or scale can be removed by soaking in the Reebaklens RR cleaning agent solution for 60 minutes.

• For the removal of mortar and plaster runs, droppings and stains from brickwork and concrete surfaces. Also for removal of hardened concrete from tools, machinery and equipment, or rust and mill scale from steelwork. 
• Suitable for etching of concrete floors and surfaces prior to application surface coatings.

• Rapid action Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action. Penetrates oil and grease.

• Reebaklens is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear blue solution.

• Fosroc provides a technical advisory service to specifiers, end-users and contractors as well as on-site technical assistance in locations all over the country.

• Cleaning brickwork: A small trial area should be cleaned first to determine the most suitable Reebaklens cleaning agent dilution. Pre-wet the brickwork, then using a sponge, rub the affected areas with a solution of Reebaklens cleaning agent and water. Strength of the solution required will vary but should be between 1:1 and 1:4 (by volume of Reebaklens cleaning agent to water). When the action has finished, wash down thoroughly with clean water.

• On re-bars during repairs to reinforced concrete structures.
• Maintenance of mild steel structures like tanks, water pipelines, shuttering plates and other corroded steel surfaces.

• Ease of application - Ready to use, easily applicable by brush.
• Penetration & effect - Effective rust removal even from areas difficult to reach & penetrate.
• Chloride free - Contains no chloride hence no chance of enhancing further corrosion.
• Economical - Cost effective because of good coverage.

• New/ old reinforcement steel in new construction.
• Embedded steel in repairable structures.
• Various steel structures like tanks, water pipelines, effluent pipelines, trusses, purlins, rafters and other structural members. 

• Rusticide Performs Rust Removal And Rust Prevention In One Operation In Mild Conditions.

WD-40 lubricates moving parts such as hinges, wheels, rollers, chains, and gears. It protects against rust and corrosion on items like tools, and sporting equipment. It penetrates to free stuck corroded parts like nuts, bolts, valves and locks. It quickly removes adhesives, corrosion and paint. It displaces moisture to restore water flooded equipment such as engines, spark plugs and power tools.

• Water can be added in a small proportion to get workable consistency.