Ametek Electronics

• 1 x Cooling fan 
• 1 x Fan gauze 
• 1 x Guide cold plate 
• 1 x Radiator 
• 1 x Thermal insulation gasket 
• 1 x Semiconductor refrigeration piece 
• 1 x Silicon grease
• 10 x Screws 

This module is a non-isolated step-up (boost) voltage converter featuring adjustable output voltage and high efficiency. The XL6009 module uses second generation of high frequency switch technology as the core chip for conversion. 

Note 1 : Vin * Iin * Efficiency = Vout * Iout 
Note 2 : The output voltage must be higher than the input voltage 

Sample Test Results: 
- Input 3V Output 12V 0.4A 4.8W 
- Input 5V Output 12V 0.8A 9.6W 
- Input 7.4V Output 12V 1.5A 18W 
- Input 12V Output 15V 2A 30W 
- Input 12V Output 16V 2A 32W 
- Input 12V Output 18V 1.6A 28.8W 
- Input 12V Output 19V 1.5A 28.5W 
- Input 12V Output 24V 1 A 24W 

Note: Vin * Iin * Efficiency = Vout * Iout 
- - Vin: Input Voltage 
- - Iin: Input current 
- - Vout: Output Voltage 
- - Iout: Output current

• Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range;
• Low ultra wide output voltage 5 v ~ 35 v;
• Built-in 4 a efficient MOSFET switch tube, make efficiency up to 94%; (LM2577 current only 3 a)
• High switching frequency, 400 KHZ, can use the small capacity of the filter capacitor can achieve very good effect, ripple smaller and smaller
• Operating temperature:-40 degrees ~+85 degrees

MPU6050 sensor module is complete 6-axis Motion Tracking Device. It combines 3-axis Gyroscope, 3-axis Accelerometer and Digital Motion Processor all in small package. Also, it has additional feature of on-chip Temperature sensor. It has I2C bus interface to communicate with the microcontrollers.

It has Auxiliary I2C bus to communicate with other sensor devices like 3-axis Magnetometer, Pressure sensor etc.

If 3-axis Magnetometer is connected to auxiliary I2C bus, then MPU6050 can provide complete 9-axis Motion Fusion output.

1. USB type B receptacle.
2. SD Card add on available.
3. Fits 5 Pololu stepper driver board.
4. LEDs indicate when heater outputs on.
5. Expandable to control other accessories.
6. Heated bed control with additional 11A fuse.
7. Option to connect 2 motors to Z for Prusa Mendel.
8. I2C and SPI pins left available for future expansion.
9. It has provisions for the cartesian robot and extruder.
10. All the Mosfets are hook into PWM pins for versatility.
11. 3 mosfets for heater / fan outputs and 3 thermistor circuits.
12. Fused at 5A for additional safety and component protection.
13. These boards are on pin header sockets so they can be replace easily or remove for use in future designs.
14. Servo style connectors are use to connect to the end stops, motors, and led. These connectors are gold plated, rated for 3A, very compact, and globally available.

This is USB controlled relay board with 4 channels. It’s uses HID USB, so no need to install any driver in  windows system. You just need to install the software. We also provide an application and the  C++ develop library that you can easy to integrate this module to your project.

This 2 Road/Channel Relay Module (with light coupling) 12V module meet the safety standard as control areas and load area have the isolation groove. Optical coupling isolation module.

The triggering of 2 Road/Channel Relay Module is reliable, more stable. The double FR – 4 circuit board design, high-end SMT process. It has power and relay operation instructions. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy.

The inputs of 2 Channel 12V Relay Module are isolated to protect any delicate control circuitry.

A wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on can control it.

The use of such high-voltage relay eliminates the risk of heating up of the relay as electromechanical relay limit the current consumption in accordance with a voltage rating.

The positive (according to the relay voltage VCC: connect power supply)
GND: connect power negative
IN1: relay module (effective) high-level trigger signal trigger end
IN2: relay module (effective) high-level trigger signal trigger end

1. High-level trigger refers to using the anode voltage at the VCC connection way of a trigger and triggers the end when the trigger side has the positive voltage or to trigger voltage when the relay is off.
2. Low-level trigger refers to using the negative voltage at the GND connection way of a trigger and triggers the end when the trigger side has 0 v low voltage or voltage to can trigger, the relay is off.

The Joystick V2.0 has added Nokia 5110 LCD and nRF24L01 interface. You can easily develop your Joystick games, and even communicate each other with wireless nRF24L01. These pinouts also helps it to easily get associated with other processors which helps to develop an user friendly environment.

The shield sits on top of your Arduino and turns it into a simple controller. 7 momentary push buttons ( 4 big buttons + 2 small buttons + joystick select button ) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers.

The Joystick v 2.0 with Nokia 5110 does not support standard Arduino board Because of standard Arduino board 3.3 v just supply 50mA current, which can't support Nokia5110 backlight need.

Features:

• One normally closed contact and one normally open contact
• Triode drive, increasing relay coil
• High impedance controller pin
• Pull-down circuit for avoidance of malfunction
• Power supply indicator lamp
• Control indicator lamp
• Indicator for Relay output status
• Can Be controlled various appliances & other Equipment With Large current.
• Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
• The module is compliant with international safety standards, control and load areas isolation trenches;

• Arduino Mega 2560 
• Pulse sensor 
• HookUp Wires 

• Pulse sensor is a plug-and-play heart-rate sensor for Arduino Mega 2560 
• It can be used to check the pulse in our body.
• It can be used by students, artists, and developers.  

• The first can be a negative pin connected to the Gnd of the Arduino Mega 2560.
• The second can be a positive pin connected to the 5V of the Arduino Mega 2560. 
• The third can be a input pin connected to the Analog pin A0 of the Arduino Mega 2560.  

Use this power regulation module to provide 5V and 3V3 power supply to your breadboard based project.This power supply board is designed to plug into a Breadboard panel with 2 power Distribution strips. The module can be powered by a USB port or an external power supply 7-12V. The module has two independent power lines, which can be set to output voltage of 5V or 3.3V, or completely remove power from the line. The module has ON / OFF switch to turn on and off module. It comes with reverse polarity and short circuit protections, which greatly helps during building and testing circuits on the breadboard.

Features:-

• Designed to fit the standard MB102 bread board
• Power Supply comes with On/Off Switch
• Green LED power indication
• Built-in protection against short-circuit through power limiting circuitry
• Compatible with 5V, 3.3V
• Two way independent control
• Output VoltageCan be switched to 0V, 3.3V, 5V
• On-board Two sets of 3.3V, 5V DC output pins, lets you connect directly to external circuits and to multiple breadboards.