Arham Agencies

Packaging Size	18.2L
Packaging Type	Can
Brand	Jotun
Solids by volume	63 +/- 2%
Gloss level	70 GU at 60 Degree
Flash Point	30 DegreeC
Density	1.4kg/L
VOC	2.7 lbs/gal
Dry Film Thickness	2 mils
Wet Film Thickness	3 mils
Theoretical Spreading Rate	510feet/gal

Hardtop XP Classic polyurethane performance

Hardtop XP is our most popular polyurethane topcoat because it combines excellent application properties with good colour and gloss retention.  

Area of use: 
Marine: Topsides, decks and superstructures Protective: Offshore environments, refineries, power plants, bridges, buildings and a wide range of industrial structuresThis is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good gloss retention. It is a high solids product. The product has good application properties with low dry spray.To be used as topcoat in atmospheric environments.

Typical use

Marine:
Recommended for topside, deck and superstructure.

Protective:

Recommended for offshore environments, refineries, power plants, bridges and buildings. Suitable for a wide range of industrial structures. Used as a topcoat in pre-qualified NORSOK systems

Approvals and certificates
 This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards.
 NORSOK System 1, Rev.5Grain, Newcastle Occupational HealthFood, Compliant with USA, FDA Title 21, Part 175.300 for dry solids
When used as part of an approved scheme, this material has the following certification:- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8
Consult your Jotun representative for details.
Additional certificates and approvals may be available on request.
 

• Good colour- and gloss retention
• Excellent application properties by airless spray
• Tailor made variants available

Packaging Size	20L
Packaging Type	Can
Brand	Jotun
Application Method	Spray, Brush
Solids by volume	51 +/- 2%
Gloss Level	35 GU at 60 DegreeC
Flash Point	25 DegreeC
Density	1.3kg/L
VOC	440g/L
Theoretical Spreading Rate	18.5m2/L
Spray Pressure at nozzle	150 bar
Surface Dry	2hrs
Induction Time	30min

Product description

This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new construction. Can be used as primer as a part of a complete system in atmospheric and immersed environments.Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop primed steel and thermally sprayed zinc substrates.

Typical use
 Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment

Approvals and certificates

When used as part of an approved scheme, this material has the following certification:- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8

- Grain, Newcastle Occupational Health
Consult your Jotun representative for details.
Additional certificates and approvals may be available on request.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures

Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system recommendation.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work.

Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation

When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to sunlight and weathering.

Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your local Jotun office for further information.

Packaging Size	10Ltr
Packaging Type	Bucket
Brand	Jotun
Finish Type	Matt
Coverage Area	9.5 sq,mtr
Provide Home Painting	No

This is a two component polyamide cured zinc epoxy coating. It provides corrosion protection as part of acomplete coating system. To be used as primer in atmospheric environments. Suitable for properly preparedcarbon steel substrates only. This product complies with ASTM D520 type II zinc dust

Additional Information:

• Delivery Time: 7 days
• Packaging Details: 10

Packaging Size	20Ltr
Brand	Jotun
Usage/Application	Metal
Grade Standard	Industrial Grade
Color	Grey
No. Of Components	Two Component
Packaging Type	Drum
Form	Liquid
Paint Base Type	Solvent Based
Is it Anti Corrosive	No
Country of Origin	Made in India

This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high buildproduct. It is reinforced with glass flakes for improved abrasion and scratch resistance. Specially designed forareas where optimum surface preparation is not possible or desired. Provides long lasting protection inenvironments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system inatmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces.It can be applied at sub zero surface temperatures.

Additional Information:

• Delivery Time: 8 to 10 days

Packaging Size	20 ltr
Packaging Type	Drum
Brand	Jotun
Finish Type	Matt
Provide Home Painting	No
Usage/Application	Industrial
Type	Alkyd Primer
Color	Gray
Country of Origin	Made in India

 This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphatepigmented product. Can be used as primer or mid coat in atmospheric environments. Suitable for properlyprepared carbon steel, aluminium and wooden substrates.

Additional Information:

• Production Capacity: Pilot QD Primer
• Delivery Time: Week
• Packaging Details: 20Ltr