Atlantis Erudition & Travel Services Private Limited

We offer a wide range of single cell Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries, that are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.2V. While the nominal voltage of the battery remains at 3.7V, which is also a safe voltage to store the battery at. 

The batteries come with a 2-pin JST connector.

The included protection circuitry keeps the battery voltage from going too high (over-charging) or low (over-use), which means that the battery will cut-out when completely dead at 3.0V. It will also protect against output shorts. However, even with this protection it is important to use a LiIon/LiPoly constant-voltage/constant-current charger to recharge and at a rate of 2A or less (500mA is best). We suggest our Micro Lipo charger, which has a 100mA default rate. You can also set the Micro Lipo to 500mA rate for a faster charge.

NOTE: We can provide custom LiPo batteries for BULK orders on demand. Please contact us for a quote. 

Physical Dimensions

In order to facilitate accurate use of these batteries, and help the use with optimum enclosure design, we are providing below, the right cube size needed to house each battery (L X B X H) and weight (including wire and connector)

1. 45 mAh (Long): 16mm X 11.5mm X 5mm | Weight: 1.85 grams
2. 45 mAh: 13mm X 9.5mm X 5mm | Weight: 1.5 grams
3. 55 mAh: 15mm X 10mm X 6mm | Weight: 1.6 grams
4. 60 mAh: 17mm X 10mm X 6mm | Weight: 1.8 grams
5. 150 mAh: 40mm X 10mm X 5mm | Weight: 3.6 grams
6. 200 mAh: 32mm X 12mm X 6mm | Weight: 4.2 grams
7. 350 mAh: 38mm X 12mm X 8.5mm | Weight: 7.3 grams
8. 400 mAh (Long): 36mm X 19.5mm X 6mm | Weight: 8 grams
9. 400 mAh: 32mm X 19mm X 8mm | Weight: 10 grams
10. 500 mAh: 36mm X 20mm X 7.5mm | Weight: 10 grams
11. 800 mAh: 41mm X 29.5mm X 5mm | Weight: 12.5 grams
12. 850 mAh: 35mm X 25mm X 9.5mm | Weight: 15 grams
13. 1000 mAh: 50mm X 20mm X 10mm | Weight: 19 grams
14. 2500 mAh: 50mm X 40mm X 10mm | Weight: 40 grams

The TS832 Transmitter packs a whopping 600mW of ultra clean 5.8GHz power! A must for those looking for longer range and locked in video. The TS832 is transmitting a full range of 32 channels and uses an easy to use 2 button interface, it also comes with a clean pre-wired harness, and only weighs in at 21g, it’s perfect for a wide range of aircraft!

Note: This is the new 48-channel edition of the 5.8Ghz 600mW AV Wireless System

• 40 channels: Cover A, B, E bands and F band (Airwave band), 4 bands and all frequencies compactable;
• Two switching buttons: CH button for frequencies channels switching, FR button for frequencies bands switching;
• Two digits display: one for CH and the other for FR, real-time positioning which frequency band and which channel received;
• Power off memory: Replay the very last frequency band and channel
• Independent video and audio signal outputs

Specifications

TX TS832 specs:

• Power input: 7.4-16V (3S Lipo suggested)
• Transmitting power: 600mA
• Antenna gain: 2db
• Working current: 220mA at 12V
• Video bandwidth: 8M
• Audio bandwidth : 6.5M
• Weight: 22g
• Dimension: 54x 32x 10mm(excluding antenna)

Resources

Datasheet

Tutorials

Universal GPS Folding Antenna Mount is used to mount GPS device on the flight. GPS devices are most accurate if their antennas have a clear view of the sky.

GPS/Compass modules are also prone to the electromagnetic interference generated by motors, ESCs, and radio transmission equipment.

Given both of these factors, for the best possible performance, it makes sense to use an extended mount to position your GPS/Compass far away from the sources of interference and well above your multirotor.

This mount measures 16cm, which is more than tall enough for most installations. Best still, the mount can be quickly folded without any tools for transportation or storage.

• CNC manufacturing, carbon fiber hole: 4.0mm
• Antenna base section can be folded, light weight and small size, compact structure, easy to use, is playing an essential tool for multi-axis ..
• The shaft hole is 4MM,
• Baby screw top containing tear carbide consistent picture! Suitable high-grade multi-axis aircraft!

Specifications

• Product Name: 4-Axis GPS Foldable Antenna Holder Base
• Size:150*38 mm
• Color: Silver, Red
• Material: Aluminum alloy + carbon fiber
• Compatible device: Quadcopter
• Functions: DJI signal bracket
• Net weight: 30 g
• Package weight: 40 g

Tutorial

1. Brand new Bullet Series (purple), super-mini, ultra-light ESC.
2. BLHeli-S firmware/ Supports MULTISHOT, ONESHOT42, ONESHOT125.
3. New heatsink design both effectively reduces the core temperature and avoids propeller strike damage.
4. Featured with High-temperature silicone signal cable for wire flexibility and ease of installation.
5. Imported MOS tube, Japanese ceramic capacitors, 3oz High-TG PCB board, significantly reduces electrical heat soak and improves system efficiency.

Specifications

Resources

Datasheet

Tutorial

1. Race Spec Performances
2. Active Cooling Fins Greatly Reduce Motor Temperatures
3. Low CG, Lightweight Design
4. Japanese Bearing For Performances
5. Enhance Anti Off U Ring For Safety & Stability
6. Dual Lock CW/CCW Locknuts
7. Dynamic balancing treatment

Specifications

• Model: R2205
• Package Contains 2x Motor - CW and CCW Pair
• Framework: 12N14P
• No. of Cells: 3 - 4S
• KV: 2300/2500
• Max Thrust: 1024g
• Diameter: 27.9mm
• Propeller Suggested: HQ 5045 BN
• Weight: 33g
• The package includes 1 motor only. 

Tutorial

The NX3 3D flight controller features a micro design, small size, supports single aileron model, V-tail model, delta wing model and dual aileron (flaperons) aircraft - Can also be used for 2 - axis on jets using 2 servos for ailerons and a servo on the elevator or if the jet uses 2 servos only, one serving the left aileron and elevator, and the other servo serving the right aileron and elevator, it can be set to a delta wing.

Features:
Humanized design, independent potentiometer adjust for different axis sensitivity
Optional - Three-mode switched from controller,

1 - normal stability mode,
2- gyro off mode,
3- calibration.

Specifications

Input voltage: DC5 - 6V, directly connected to the ESC's BEC power supply can be use.
Operating Current: 18mA
Working temperature: -20 Celsius to 85 Celsius
Dimensions: 25 × 40mm
Net Weight: 6.5g

Resources

Datasheet

Tutorial

The FS-R6B Flysky 2.4ghz 6CH Receiver For Rc FS-CT6B TH9X Receives Signal From Compatible Transmitter.

In the world of racing of drones, the basic requirement is for small and lightweight components that will make a drone more and more nimble. This FS-R8S receiver fits these requirements superbly by being very small in size and light in weight.

Specifications

Channels: 6 Channels
Model Type: Heli, Airplane, Gliders
RF Power: Less than 20db
Modulation: GFSK
Code Type: PCM
Sensitivity: 1024
Low Voltage Warning: LED
DSC Port: Yes
Charger Port: Yes

Tutorial

This F450 Quadcopter Frame PCB Board is a well thought out 450mm quad frame built from quality materials. The Board is made of glass fiber. This board provides integrated PCB connections for direct soldering of your ESCs. New design PCB board version fit for standard 50mm controller board such as MK, KK, FF, MWC;

This eliminates the need for a power distribution board or messy multi-connectors keeping your electronics layout very tidy. It also comes with stronger moulded construction so no more board breakage at the hard landing.

Package included

• 6 x Flame Wheel(2 Red,2 White)
• 1 x F450 TOP Plate
• 1 x F450 BOTTOM Plate
• 16 x F-M3*8 Screws
• 24 x F-M2.5*8 Screws

Specification

• Color: White & Red
• Frame arm size: 21.5 * 3.8 * 5cm / 8.5 * 1.6 * 2.0inch
• Weight: 43g(Single)
• Weight: 250g / 4pcs
• Colour: Black Plate
• Material: Glass Fiber

Resources

CAD Files

Tutorials

Specifications

• Temperature: -25 ~ + 70 ° C
• Rel, Humidity: 35% ~ 85% RH
• Pressure: 86 ~ 106Kpa
• Environmental noise: Maximum: 36dB
• Operating voltage: 1 ~ 10VDC
• Operating Voltage Standard: 2VDC
• Impedance: Maximum: 2.2k Ω
• Current consumption: Maximum: 0.5mA
• Sensitivity:  (0dB = 1 V / Pa, 1 KHz) -58dB ± 3dB Vs = 2 V R1 = 2.2k Ω
• Directivity: Omni-directional
• S / N ratio: Minimum: 58dB
• Test temperature: 20 ° C ± 2 ° C
• Rel. Humidity: 45% ~ 65% RH

Specifications

Resources

Sample Code

Tutorial

Specifications

• power supply: 5V
• Frequency range: 76-108MHZ
• PCB size: 31*30mm
• With reverse polarity protection diode
• With power output filtering sensor
• Directly plug antenna interface
• I2C bus communication
• Multi capacitor combined filter
• Blue LED power indicator
• FM chip module TEA5767
• Onboard 3.5mm audio interface
• If connects with singlechip, only connect the Power Ground and two I2C communication cable

Features:

• LC harmonic oscillator use low cost fixed chip
• No need to adjust Intermediate frequency
• High sensitivity(low noise RF input amplifier)
• High power auto gain control AGC circuit
• Soft mute

Specifications

Resources

Datasheet

Library

Sample Code

Tutorial

• Solar panel input: 4.4-6V
• Max charge current: 500mA
• Interface: 2-pin JST connectors(or PH2.0)
• Short circuit protection
• Continuous Charge Current Up to 500mA
• Battery status indication ( Red : Charging , Green: Charged )
• Support USB Charge (Micro-USB Connector)

Specifications

Resources

Datasheet

Tutorial

Mini Stepper Motor for Lighter projects requiring precise geared control.

A stepper motor is an electromechanical device which converts electrical pulses into discrete mechanical movements. The shaft or spindle of a stepper motor rotates in discrete step increments when electrical command pulses are applied to it in the proper sequence. The motors rotation has several direct relationships to these applied input pulses. The sequence of the applied pulses is directly related to the direction of motor shafts rotation. The speed of the motor shafts rotation is directly related to the frequency of the input pulses and the length of rotation is directly related to the number of input pulses applied.One of the most significant advantages of a stepper motor is its ability to be accurately controlled in an open loop system. Open loop control means no feedback information about position is needed. This type of control eliminates the need for expensive sensing and feedback devices such as optical encoders. Your position is known simply by keeping track of the input step pulses.

Specifications

• Reduction Ratio: 1:64
• Step Angle: 5.625
• Voltage: 5V
• Diameter: 28mm
• 5-Line 4-phase can be driven by ordinary ULN2003 chip ,can also be connected in phase 2 development board used for supporting the use of a direct plug and easy to use stepper motor used in the development board

Resources

Datasheet

Sample Code

Tutorial

G1200 Digital / Electronic Microscope 1X-1200X

This is a digital microscope with continuous zoom, and it has a wide range of viewing options compared to other microscopes, ranging from 1 to 1200 times magnification, and always finding a suitable multiple for you.

Adjustable angle can solve the problem of high reflection by the LEDs lights. The microscope has a longer range than the others because it has certain amount of room to operate. It is very convenient to use tweezers, electric soldering iron and others under your microscope.

This product has a built-in battery backup.

• HD 12 megapixel
• Display Screen: 7-inch HD LCD display
• 1-1200 * continuous amplification system.
  

Specifications:

• Pixel: HD 12 megapixel
• Display Screen: 7-inch HD LCD display
• Magnification: 1X - 1200X continuous amplification system.
• Distance Between Object: 10MM to infinity (different distances correspond to different multiples)
• Sixteen Language Systems: English, Spanish, Russian, Korean, Japanese, Thai, Hebrew, Portugal, German, French, Italy, Turkey, Czech, Poland, Traditional Chinese, Simplified Chinese.
• Cell(built-in): 1 * 3.7V 3000mAh Lithium Cell
• Package Size: 205 * 160 * 80mm / 8.1 * 6.3 * 3.1in
• Package Weight: 1200g / 2.6lb

Advantage:

1. Vertical microscopes have an important drawback because they are used in many applications such as solder on PCBs, model designation of some tiny chips, and metals, and it is easy to lose sight of the details of the objects due to reflection. Our product specifically addresses this issue. It is an angle-adjustable digital microscope that solves the problem of high reflection. It's a suitable experience in the electronics maintenance industry, and it's important to note that. This machine has a longer range than the others because it has certain amount of room to operate. It is very convenient to use tweezers, electric soldering iron and others under your microscope.
2. Most other microscopes are two-gears magnification, either too large or too small. There will always be visual regret. This is a digital microscope with continuous zoom and zoom, and it has a wide range of viewing options compared to other microscopes, ranging from 1 to 1200 times magnification, and always finding a suitable multiple for you to.

Button Setting: Power: press 2 seconds to turn on/off

M Key: Function setting

• Screen Saver: Off * 30 sec/1 mins/2 mins (optional)
• Automatic Shutdown: Off * 3 minutes/5 minutes/10 minutes
• Hz Light Source: 50 Hz/60 Hz
• Language options: 16 Languages
• Date Adjustment: year, month, day｜hour, minute, second
• Format: YES/NO
• Default: YES/NO

In Video Mode:

• Resolution: 1080FHD, 720P, VGA
• Circulating Camera: Off/3 minutes/5 minutes/10 minutes. When the flash memory card is full, the foremost video data will be deleted and the video will be saved.

• Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz
• 1GB LPDDR2 SDRAM
• 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE
• Gigabit Ethernet over USB 2.0 (maximum throughput 300 Mbps)
• Extended 40-pin GPIO header
• Full-size HDMI
• 4 USB 2.0 ports
• CSI camera port for connecting a Raspberry Pi camera
• DSI display port for connecting a Raspberry Pi touchscreen display
• 4-pole stereo output and composite video port
• Micro SD port for loading your operating system and storing data
• 5V/2.5A DC power input
• Power-over-Ethernet (PoE) support (requires separate PoE HAT)

Raspberry Pi 3 Model B+ is a premium quality Raspberry Pi from Raspberry Pi Foundation. All Raspberry Pi 3 Model B+ are manufactured using quality assured material and advanced techniques, making them up to the standard in this highly challenging field. The materials utilized to manufacture Raspberry Pi 3 Model B+, are sourced from the most reliable and official Raspberry Pi vendors, chosen after performing detailed market surveys. 

Specifications

Resources

Datasheet

Tutorial

• This hot air rework station features a PID programmable temperature control system and real time temperature tracking of each component, as well as an automatic temperature correction with rapid speed compensation and minimum tolerance.
• It comes equipped with a hot air gun and soldering iron.
• The anti-static design prevents static or electricity leakage.
• Personalized Functions:
  A. Temperature Correction Function:
  The rework station will automatically correct the temperature due to environmental changes or replacement of the heating coil, soldering iron or other components.
  B. Sleep Mode:
  The soldering iron automatically goes to sleep if it is left in a still condition for 10 minutes, and the temperature will decrease to 200℃. This prevents the iron tip from oxidizing and other damage, as well as eliminates the need for a heat waiting period.
  Activation Method:
  a). Shake the iron handle several times.
  b). Press any button once.
  C). Power-off first and then power-on.
  C. Cold/Hot Air Switch:
  Switch from cold or hot air by pressing the button-the cold air function is especially designed to cool down heated elements processing.

The NX3 3D flight controller features a micro design, small size, supports single aileron model, V-tail model, delta wing model and dual aileron (flaperons) aircraft - Can also be used for 2 - axis on jets using 2 servos for ailerons and a servo on the elevator or if the jet uses 2 servos only, one serving the left aileron and elevator, and the other servo serving the right aileron and elevator, it can be set to a delta wing.

Features:
Humanized design, independent potentiometer adjust for different axis sensitivity
Optional - Three-mode switched from controller,

1 - normal stability mode,
2- gyro off mode,
3- calibration.

Specifications

Input voltage: DC5 - 6V, directly connected to the ESC's BEC power supply can be use.
Operating Current: 18mA
Working temperature: -20 Celsius to 85 Celsius
Dimensions: 25 × 40mm
Net Weight: 6.5g

Resources

Datasheet

Tutorial

Gens ACE High Discharge Lipo Battery 3S 11.1V 30C

Gens ace lipo battery packs have remarkable stacking technology which enables high current capacity cells. With High discharge performance and high energy density, GensAce batteries provide high quality, reliable power for MIKADO LOGO500, ALIGN T-REX550/600, GAUI X5, Outrage 550, Hirobo SDX, FPV and custom made racing drones.

Nominal Charge Current should be kept at 1C for peak battery life.

Gens ace 3S1P Lipo Battery Pack Specs:

• 1300mAh 30C 11.1V 3S
• Capacity: 1300mAh
• Electric core: 3S1P
• Voltage: 11.1V
• Discharge rate: 30C
• Discharge wire: 80mm, silicone wire
• Charging line: 45mm, silicone wire
• Size(HxWxL): 19x33x71mm
• Weight(士15g)：109.5g
• 2200mAh 30C 11.1V 3S
• Capacity: 3300mAh
• Electric core: 3S1P
• Voltage: 11.1V
• Discharge rate: 30C
• Discharge wire: 80mm, silicone wire
• Charging line: 45mm, silicone wire
• Size(HxWxL): 20x32x112mm
• Weight(士15g): 182g
• 3300mAh 30C 11.1V 3S
• Capacity: 3300mAh
• Electric core: 3S1P
• Voltage: 11.1V
• Discharge rate: 30C
• Discharge wire: 80mm, silicone wire
• Charging line: 45mm, silicone wire
• Size(HxWxL): 17x40x136mm
• Weight(士15g): 234g
• 4000mAh 30C 11.1V 3S
• Capacity: 4000mAh
• Electric core: 3S1P
• Voltage: 11.1V
• Discharge rate: 30C
• Discharge wire: 80mm, silicone wire
• Charging line: 45mm, silicone wire
• Size(HxWxL): 22x40x138mm
• Weight(士15g): 288g

NEMA 24 EASY SERVO MOTOR & DRIVER

NEMA 24 closed loop stepper motor as the controlled output returns to the control input in a certain way and exerts control influence on the input. The closed-loop control of the stepper motor uses position feedback or speed feedback to determine the phase conversion corresponding to the rotor position, which can greatly improve the performance of the stepping motor. These motors are also called Easy Servo Motors.

Motor Parameters:

• Model: 60HSE3N-D25
  
• Step Angle:  1.8°
• Rated Current: 5.0A
• Rated Voltage: 2.25VDC
• Phase Resistance: 0.45 ± 10%Ω
• Phase Inductance: 1.8 ± 20%mH
• Holding Torque: 3 N.m 
• Surface Treatment: Black Electrophoresis
• Dielectric Strength: 500VAC / 5mA / 1min
• Insulation Resistance: ≥100M Ω / 500VDC
• Insulation: Class B
• Motor Length: 76mm
• Total Length: 97mm
• Encoder Resolution: 1000 pulse per rotation
• Shaft Radial Play 0.02Max.(450g-load)
• Shaft Axial Play 0.08Max.(450g-load)
• Weight: 1.55kg

Torque/Frequency Curve

DRIVER DIMENSIONS

WIRING DIAGRAM

Features

• 3 lenses 18-720x, 1560-2040x, 2760-4080x continuous zoom in for hobby, Industrial and biologic purposes. Reversed quadruple nosepiece slots, Two empty lens slots (RMS 20.2mm) so users could use their own lens for certain use.
• 10.1 inch built-in monitor ensures an easy and comfortable observation for all users including eyeglass wearers. The device can take videos up to 2880*2160 resolution, picture resolution reaches 24M 5600*4200 (with interpolation).
• The lifting bracket is made of metal and plastic: the metal part helps to firmly fix the monitor still, plastic part effectively reduces static electricity. The lower part has a bigger diameter, which naturally gives a lower limit stop to prevent the monitor from accidental dropping to slides
• Mechanical stage, size of 122*138mm with a movement range of 0-58mm vertically, on where you place slides and what to move to find the best image and magnifications. It comes with a hole in the middle, where the bottom light goes through and to set the three backdrop boards to observe different slides
• Multiple outputs: HDMI to a monitor, USB to a computer or simply use a memory card to save all images you capture. The gift-giving Windows software offers image-development and measurement tools, as well as advanced compositing features such as "sharpness" and "edge detect".

Lens A-Coin Microscope Applications: coin, stones, stamp collection, circuit board observation. Highlights: Whole or partial Coin can be observed with a 12-320mm working distance.

The Mini Router is equipped with dual Gigabit Ethernet ports and dual USB 3.0 ports, making it suitable for soft router applications, while keeping the hardware to a minimum. We have pre-installed a Raspberry Pi Compute Module 4 with 4GB RAM and 32GB eMMC to enable fast boot-up times and a smooth overall experience. 

Features

• Fast boot times and smooth overall experience: Powered by Raspberry Pi Compute Module 4 and 4GB RAM/32GB eMMC
• Compact and highly integrated: 75x64x21mm in size, with dual Gigabit Ethernet ports and dual USB3.0 ports
• Highly scalable with rich IO peripherals: dual Gigabit Ethernet connectors, Micro-SD card slot, micro-HDMI interface, USB 3.0, MIPI CSI, MIPI DSI, etc.
• Easy to deploy with stability: DIN rail mount and keyhole slot allow you to hang it anywhere
• Pre-installed OpenWrt firmware: Out of the box, can easily implement software router applications

Out of the two Gigabit Ethernet Ports (RJ45), one Ethernet Port is connected to the Gigabit Ethernet PHY of the CM4 module which is based on Broadcom BCM54210PE. On the other hand, the other Gigabit Ethernet Port is connected to Microchip's LAN7800 which is a USB 3.0 to GbE (Gigabit Ethernet Bridge). The USB 3.0 interface here is extended from the PCIe interface of the CM4 Module. Also, both ports can support speeds up to 1Gbps.

It features a variety of I/O peripherals such as MIPI CSI, MIPI DSI, micro-HDMI to connect displays/ cameras, a standard 9-pin USB 3.0 header for more USB expansion, a micro-SD card slot, and an FPC connector while maintaining a compact form factor! This board is ideal for HTPC makers, Linux developers, software router enthusiasts, and the majority of regular Raspberry Pi users.

Also, this comes included with a PC/ABS case with an Aluminum alloy on top which has a large sink in order to cool down the CM4 at extreme loads. It provides better protection as well and is suitable to be used in industrial applications.

Heat Maps

Specifications

Item Name: Direct drive propeller
Model: 7035
Quantity: 1
Color: Orange
Weight: About 6g each
Center Bore: 4mm

1CW 1CCW

Seeed’s ReSpeaker 4-MicsLinear Array Kit for Raspberry Pi is an extension board, aka HAT designed for Raspberry Pi. It's a linear microphone array kit, comes with four microphones and designed for AI and voice applications. That means you can build a more powerful and flexible voice product with Raspberry Pi which can integrate Amazon Alexa Voice Service, Google Assistant, and so on.

ReSpeaker 4-Mic Linear Array Kit for Raspberry Pi consists of two boards, one is voice accessory HAT, another is four microphones linear array.

ReSpeaker 4-Mic Linear Array Kit for Raspberry Pi support 8 input & 8 output channels in the Raspbian system. The first 6 input channels for microphone recording(only first 4 input channels are valid capture data), the rest of the 2 input channels are echo channels of playback. The first 2 output channels for playing, the rest of the 6 output channels are dummy.

Features

• 2 ADC chips and 1 DAC chip
• 8 input and 8 output channels
• Four microphones array
• Grove support
• Compatible with Raspberry Pi 40-pin headers
• Headset and speaker voice output
• Compatible with Raspberry Pi 4

 What is ReSpeaker? 

ReSpeaker is an open modular voice interface to hack things around you. Let you interact with your home appliances, your plant, your office, your internet-equipped devices, or any other things in your daily life, all by your voice. The ReSpeaker project provides hardware components and software libraries to build voice-enabled device.

This is an ideal storage solution for Raspberry Pi 3 Model  B+ or Raspberry Pi 4, offering dual mSATA SSD Shield, it supports 2 picese of mSATA SSD working at the same time, with USB3.1 Gen 1 port, SSD sequential write speed >300MB/s, use the new USB 3.0 connector.

Features

• Ideal storage solution for Raspberry Pi - Dual MSATA SSD Shield
• Supports up to 2TB MSSD solid-state drive (SSD)
• Supports 2 MSATA SSD working at the same time
• Supports operating system installation and booting from your SSD
• Provides additional 2 USB ports for Raspberry Pi
• Powers the Raspberry Pi via on-board XH2.54 connector - Only one power adapter required
• Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controller
• Integrated USB 3.1 Gen 1 Hub Controller
• USB 2.0 connectivity offers plug-and-play functionality on your Raspberry Pi
• Quick file transfer with high-speed USB3.0 5Gb/s connectivity from a PC or a Mac
• Specially-made USB3.0 jumper to connect with Raspberry Pi - no additional cables needed
• LED blue indicator indicates drive status
• Fully compatible with X735 for intelligent and safe power management
• PCB Size: 107.5mm x 85mm

IMPORTANT NOTES

• USB3.1 Gen 1 port, SSD sequential write speed >300MB/s
• mSATA SSD is not included
• As with all SSDs, new media must be formatted before use
• Performance depends on host system, workload, and SSD media used
• SSDs use exceptionally high performance storage media that will run hot when under load
• Older SSD drives with less efficient flash media may not perform as well as newer drives

Power Supply: 5.1Vdc +/-5% , 4A

(Please use an external DC jack power supply to power X852 if the hard disk cannot be recognized.)

 Three Kind of Power Supply Mode:

1. Use DC 5V 4A power adapter with DC jack to power the X852, use 2Pin cable to connect Raspberry Pi GPIO and X852 (recommended).
2. Use DC 5V 4A power adapter with DC jack to power the X735 (you need to purchase X735 seperately), use 2pin cable to connect X735 and X852 (recommend)
3. Use common power adapter power Raspberry Pi via RPi micro USB, use 2Pin cable to connect Raspberry Pi GPIO and X852, this is not recommended. As the Raspberry Pi micro USB only support Max. 2.5A, so the X852 maybe not get enough current to recognize the SSD. Although this power supply mode is ok to power the kit, it is not be recommended strongly to use this mode.

Ports & Connectors

• USB socket - USB 3.0 type A x 1
• DC jack - 5.5x2.5mm x 1
• Power input / output connector - XH2.54 2-pin x 1

Packing List

• 1 x X852 Board (Not include Raspberry pi 3 model B+)
• 1 x USB3.0 Connector
• 1 x USB 3.0 A-Male to A-Male Data cable
• 1 x Screws Pack

The Yihua 853AAA BGA rework station is equipped with a pre-heating platform in addition to a hot air gun and soldering iron. This soldering equipment is more practical than similar rework stations as the integrated rework station can satisfy almost all applications thanks to its 3-in-1 design, compact structure, and powerful and economical functions.

The pre-heating platform heats up the processed IC components before de-soldering and soldering processes, resulting in higher efficiency and space saving performance.

Features:

• YH-853AAA soldering iron wire adopts thermal resistant silicon material, which displays no obvious damage after 30 seconds contact with a 300℃ soldering iron tip.
• Brand name high-power heater with superfast heating time, is applicable for the soldering and de-soldering of large terminals, welding joints other than regular welded workpieces.
• Pioneer technology in this industry regarding its handle protection function, the air gun and soldering iron handles have to be placed on the holder when powering on the rework station to begin normal functioning. The main reason is for safety to prevent the handles from causing damage if left in an unsafe location.

Technical Parameters:

• Rated voltage: AC 220V±10% 50Hz
• Power Rating: 1200W
• Working environment: 0～40℃ with relative humidity＜80％
• Storage environment: －20～80℃ with relative humidity＜80％
• Body dimension: L320xW220xH100mm±5mm
• Weight: 6.5kg

Hot Air Gun Parameters:

• Output power: 650W
  
• Temperature range 100℃～480℃
• Airflow type: Brushless Motor with smooth air delivery
• Air Flow: 120L/min
• Temperature Stability: ±1℃ (static)
• Display Type: red LED
• Temperature correction type: PID digital program
• PID Temperature correction cycle: 20ms
• Heating elements: Ceramic skeleton heater

853AAA Soldering Iron Parameters:

• Output power: 75W
  
• Temperature range 200℃～480℃
• Temperature Stability: ±1℃ (static)
  
• Display Type: red LED
• Temperature correction type: PID digital program
• PID Temperature correction cycle: 100ms
• Heating elements: Imported Heater
• Tip Ground Impedance: <2 Ω

Pre-heater platform

• Output power: 600W
  
• Pre-heating platform area: 120X120mm
• Pre-heating platform material: Ceramic heating material
• Temperature sensor Type: K thermocouple
• Temperature range: 50℃ - 400℃

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and "locked in". Suited for quads up to 2.5kg, octos up to 5kg. The ESCs do not overheat, burn or lock out - unline many other ESCs flashed with the SimonK firmware. The ESC motor leads are reduced to simple bullet connectors, this allows for quick and clean installation inside your multi rotor. Compatible with 2S to 3S battery

Specifications

simonk10A (2-3S):

Weight: 10 g
Size: 23.5x15x 6.1
Input voltage: (2-3 s Lixx).
Drive current: 10A (Max: 13 A/10S)
BEC Input :3V1A
Compatible signal frequency:30Hz - 499Hz


Simonk12A ( 2-3S ):

Weight:12g
Size:28*20*6.1
Input voltage:2-3S Lixx
Drive current:12A (Max:14A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk15A (2-3S):

Weight:15g
Size:50*22*8
Input voltage:2-3S Lixx
Drive current:15A (Max:25A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk20A (2-3S):

Cont Current: 20A
Burst Current: 28A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-3S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 21g
Size: 32*24*7mm


simonk30A(2-4S):

Max cont. current: 30A
Peak current: 40A (10s)
Voltage: 2-3S lixx,
BEC: 5V/3A
Size: 50x23x8mm
Weight: ~28g


simonk30A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:25g
Size:50*23*8
Input voltage: (3-6S Lixx)
Drive current:30A (Max:40A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk40A(2-4S):

Weight:35g
Size:68*25*8MM
Input voltage:2-4S
Drive current:40A (Max:50A/10S)
BEC Input: 5V 3A
Compatible signal frequency: 30Hz - 500Hz


simonk50A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:48g
Size:53*32*10
Input voltage: (2-6S Lixx)
Drive current:50A (Max:60A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk70A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:70G
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:85A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk80A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:75g
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:90A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz

Resources

Datasheet

Tutorial

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and "locked in". Suited for quads up to 2.5kg, octos up to 5kg. The ESCs do not overheat, burn or lock out - unline many other ESCs flashed with the SimonK firmware. The ESC motor leads are reduced to simple bullet connectors, this allows for quick and clean installation inside your multi rotor. Compatible with 2S to 3S battery

Specifications

simonk10A (2-3S):

Weight: 10 g
Size: 23.5x15x 6.1
Input voltage: (2-3 s Lixx).
Drive current: 10A (Max: 13 A/10S)
BEC Input :3V1A
Compatible signal frequency:30Hz - 499Hz


Simonk12A ( 2-3S ):

Weight:12g
Size:28*20*6.1
Input voltage:2-3S Lixx
Drive current:12A (Max:14A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk15A (2-3S):

Weight:15g
Size:50*22*8
Input voltage:2-3S Lixx
Drive current:15A (Max:25A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk20A (2-3S):

Cont Current: 20A
Burst Current: 28A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-3S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 21g
Size: 32*24*7mm


simonk30A(2-4S):

Max cont. current: 30A
Peak current: 40A (10s)
Voltage: 2-3S lixx,
BEC: 5V/3A
Size: 50x23x8mm
Weight: ~28g


simonk30A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:25g
Size:50*23*8
Input voltage: (3-6S Lixx)
Drive current:30A (Max:40A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk40A(2-4S):

Weight:35g
Size:68*25*8MM
Input voltage:2-4S
Drive current:40A (Max:50A/10S)
BEC Input: 5V 3A
Compatible signal frequency: 30Hz - 500Hz


simonk50A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:48g
Size:53*32*10
Input voltage: (2-6S Lixx)
Drive current:50A (Max:60A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk70A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:70G
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:85A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk80A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:75g
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:90A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz

Resources

Datasheet

Tutorial

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and "locked in". Suited for quads up to 2.5kg, octos up to 5kg. The ESCs do not overheat, burn or lock out - unline many other ESCs flashed with the SimonK firmware. The ESC motor leads are reduced to simple bullet connectors, this allows for quick and clean installation inside your multi rotor. Compatible with 2S to 3S battery

Specifications

simonk10A (2-3S):

Weight: 10 g
Size: 23.5x15x 6.1
Input voltage: (2-3 s Lixx).
Drive current: 10A (Max: 13 A/10S)
BEC Input :3V1A
Compatible signal frequency:30Hz - 499Hz


Simonk12A ( 2-3S ):

Weight:12g
Size:28*20*6.1
Input voltage:2-3S Lixx
Drive current:12A (Max:14A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk15A (2-3S):

Weight:15g
Size:50*22*8
Input voltage:2-3S Lixx
Drive current:15A (Max:25A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk20A (2-3S):

Cont Current: 20A
Burst Current: 28A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-3S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 21g
Size: 32*24*7mm


simonk30A(2-4S):

Max cont. current: 30A
Peak current: 40A (10s)
Voltage: 2-3S lixx,
BEC: 5V/3A
Size: 50x23x8mm
Weight: ~28g


simonk30A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:25g
Size:50*23*8
Input voltage: (3-6S Lixx)
Drive current:30A (Max:40A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk40A(2-4S):

Weight:35g
Size:68*25*8MM
Input voltage:2-4S
Drive current:40A (Max:50A/10S)
BEC Input: 5V 3A
Compatible signal frequency: 30Hz - 500Hz


simonk50A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:48g
Size:53*32*10
Input voltage: (2-6S Lixx)
Drive current:50A (Max:60A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk70A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:70G
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:85A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk80A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:75g
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:90A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz

Resources

Datasheet

Tutorial

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and "locked in". Suited for quads up to 2.5kg, octos up to 5kg. The ESCs do not overheat, burn or lock out - unline many other ESCs flashed with the SimonK firmware. The ESC motor leads are reduced to simple bullet connectors, this allows for quick and clean installation inside your multi rotor. Compatible with 2S to 3S battery

Specifications

simonk10A (2-3S):

Weight: 10 g
Size: 23.5x15x 6.1
Input voltage: (2-3 s Lixx).
Drive current: 10A (Max: 13 A/10S)
BEC Input :3V1A
Compatible signal frequency:30Hz - 499Hz


Simonk12A ( 2-3S ):

Weight:12g
Size:28*20*6.1
Input voltage:2-3S Lixx
Drive current:12A (Max:14A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk15A (2-3S):

Weight:15g
Size:50*22*8
Input voltage:2-3S Lixx
Drive current:15A (Max:25A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk20A (2-3S):

Cont Current: 20A
Burst Current: 28A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-3S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 21g
Size: 32*24*7mm


simonk30A(2-4S):

Max cont. current: 30A
Peak current: 40A (10s)
Voltage: 2-3S lixx,
BEC: 5V/3A
Size: 50x23x8mm
Weight: ~28g


simonk30A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:25g
Size:50*23*8
Input voltage: (3-6S Lixx)
Drive current:30A (Max:40A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk40A(2-4S):

Weight:35g
Size:68*25*8MM
Input voltage:2-4S
Drive current:40A (Max:50A/10S)
BEC Input: 5V 3A
Compatible signal frequency: 30Hz - 500Hz


simonk50A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:48g
Size:53*32*10
Input voltage: (2-6S Lixx)
Drive current:50A (Max:60A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk70A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:70G
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:85A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk80A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:75g
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:90A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz

Resources

Datasheet

Tutorial

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and "locked in". Suited for quads up to 2.5kg, octos up to 5kg. The ESCs do not overheat, burn or lock out - unline many other ESCs flashed with the SimonK firmware. The ESC motor leads are reduced to simple bullet connectors, this allows for quick and clean installation inside your multi rotor. Compatible with 2S to 3S battery

Specifications

simonk10A (2-3S):

Weight: 10 g
Size: 23.5x15x 6.1
Input voltage: (2-3 s Lixx).
Drive current: 10A (Max: 13 A/10S)
BEC Input :3V1A
Compatible signal frequency:30Hz - 499Hz


Simonk12A ( 2-3S ):

Weight:12g
Size:28*20*6.1
Input voltage:2-3S Lixx
Drive current:12A (Max:14A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk15A (2-3S):

Weight:15g
Size:50*22*8
Input voltage:2-3S Lixx
Drive current:15A (Max:25A/10S)
BEC Input:5V2A
Compatible signal frequency: 30Hz - 499Hz


simonk20A (2-3S):

Cont Current: 20A
Burst Current: 28A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-3S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 21g
Size: 32*24*7mm


simonk30A(2-4S):

Max cont. current: 30A
Peak current: 40A (10s)
Voltage: 2-3S lixx,
BEC: 5V/3A
Size: 50x23x8mm
Weight: ~28g


simonk30A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:25g
Size:50*23*8
Input voltage: (3-6S Lixx)
Drive current:30A (Max:40A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk40A(2-4S):

Weight:35g
Size:68*25*8MM
Input voltage:2-4S
Drive current:40A (Max:50A/10S)
BEC Input: 5V 3A
Compatible signal frequency: 30Hz - 500Hz


simonk50A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:48g
Size:53*32*10
Input voltage: (2-6S Lixx)
Drive current:50A (Max:60A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk70A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:70G
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:85A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz


simonk80A-OPTO (2-6S)
(the ESC need the power from receiver or the flight control)

Weight:75g
Size:78*38*15MM
Input voltage: (2-6S Lixx)
Drive current:50A (Max:90A/10S)
BEC Input : NO
Compatible signal frequency: 30Hz - 500Hz

Resources

Datasheet

Tutorial

Specifications

Resources

Tutorial

High quality and rechargeable performance Lightweight, durable, practical and convenient to use Low energy consumption Compact, convenient and easy to replace Easy to install. Suit for: H8C,DFD F183 mini quadcopter

Specifications

Model: 8520
Diameter : 8.5mm/0.3 inch
Length : 20mm/0.8 inch
Package size: 128 x 88mm/5 x 3.5 inch
Net weight: 21.5g
Package weight: 23g

Tutorial

High quality aluminum material. Suitable for brushless motors and speed controllers.
Manufactured with accurate workmanship.

Package Includes:

• 1x Propeller Adaptor

Specifications

1. Color: Silver
2. Material: Aluminum

Variants

1. 6mm to 4mm - Aperture: 4.0 (Motor Shaft) & Output Shaft Diameter: 6mm
2. 6mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 6mm
3. 6mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 6mm
4. 5mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 5mm
5. 5mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 5mm

High quality aluminum material. Suitable for brushless motors and speed controllers.
Manufactured with accurate workmanship.

Package Includes:

• 1x Propeller Adaptor

Specifications

1. Color: Silver
2. Material: Aluminum

Variants

1. 6mm to 4mm - Aperture: 4.0 (Motor Shaft) & Output Shaft Diameter: 6mm
2. 6mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 6mm
3. 6mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 6mm
4. 5mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 5mm
5. 5mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 5mm

High quality aluminum material. Suitable for brushless motors and speed controllers.
Manufactured with accurate workmanship.

Package Includes:

• 1x Propeller Adaptor

Specifications

1. Color: Silver
2. Material: Aluminum

Variants

1. 6mm to 4mm - Aperture: 4.0 (Motor Shaft) & Output Shaft Diameter: 6mm
2. 6mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 6mm
3. 6mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 6mm
4. 5mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 5mm
5. 5mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 5mm