Bonna Agela India Private Limited

VM96 Features

The degree of vacuum can be controlled by adjusting the needle value

Vacuum gauge shows the degree of vacuum

Corrosion-resistant design of the whole system

Elevate the module by adding collection plate

VM96 Operation Procedures

Use vacuum tubing to connect the suction port of VM96 and the inlet pot of the vacuum pump;

Remove the top cover of VM96, and put 96-well collection plate into the cavity of the bottom cover of VM96;

Put back the top cover;

Put the 96-well SPE plate exactly on the top cover of VM96;

Make sure the gas valve at vacuum state (perpendicular). Start the vacuum pump, adjust the vacuum valve to suitable degree of vacuum (i.e. SPE plate flow rate);

After elution, rotate the gas valve 90 degree to non-vacuum state. Then remove the 96-well SPE plate. Note This device is a precision vacuum device, keep in mind is not removable to avoid collisions, so as to avoid a vacuum leak warranty.

* Note Collection plate spacer could be used for micro collection plate to avoid cross contamination.

VM96 Specifications

Tentative Price 200000 to 2500000 Rupees

A Positive Pressure SPE Manifold Designed for Drug R&D Labs MULTI-SPE M48 is a manual SPE manifold with 48 positions special designed for high throughput R&D laboratories of pharmaceutical industry. Positive pressure eliminates the differences of the flow-rate between the cartridges that encountered frequently on vacuum SPE devices. Therefore, MULTISPE M48 will provide highly uniform extraction which may improve the reproducibility of the recoveries. When processing viscous samples such as blood, vacuum manifold often cannot provide adequate pressure since the maximum pressure is limited to atmospheric (< -15 psi). In contrast to vacuum manifold, the Multi-SPE M48 provide maximal 60 psi pressure. Gas pressure up to 60 psi., avoiding clogging issue when loading sticky or viscous samples. A step indicator is installed on the front panel of MULTI-SPE M48 so that the user can mark SPE process step by step.

Features and Advantages

Low variation on the flow-rates between the cartridges, improving the extraction consistency.

High-throughput by processing maximal 48 samples simultaneously.

Good flexibility can control on/off for gas by each 12 positions to save gas; can run any number of samples between 1-48.

Separated tuning to get precisely pressure control.

The SPE stage indicator could be manually be switch ed to the indicator position to remember the current stage of your operation.

The whole SPE process can be completed in an inert (N2) environment when N2 gas source is provided.

Tentative Price 200000 to 2500000 Rupees

Max sample loading volume 1-5000 mL, fits different application requirement

Five kinds of solvent available

Modularly design,each module could process 6 samples gradually. One control module could control max 4 extraction modules, and 24 samples could be processing in lin

Multistep eluent collection, meets flexible application requirement

Flow speed area: 0.1-30 mL/min Accuracy : ±2

Compatible with 1-12mL SPE cartridge

Tentative Price : 200000 to 2500000 Rupees

The Qdaura Automated SPE system is specifically designed for high throughput sample preparation. The system automates routine SPE procedures from conditioning, sample loading, washing, dry and elution. The Qdaura utilizes positive pressure to ensure more reproducible flow rates, more reproducible recoveries, less sample to sample contamination, and higher precision. The built-in tasks optimized the steps during extraction to eliminate cross-contamination. The system can treat 1-4 samples parallel and up to 24 samples can be performed with in a run. The Qdaura could been used in the area of agricultural, food testing and antibiotic residue detection.

Tentative Price : 200000 to 2500000 Rupees

Stable · Effective · Simple Operation

NV-96G is designed for small volume elute concentration in drug screening, hormone assay, biochemical analysis and drug metabolism. This concentrator is compatible with most of commercial 96 well collection plate without 2nd transfer. The holder panel for collection plate could be elevated or brought down automatically to keep the needles close to the liquid interface. This evaporator is widely used in clinical analysis and DMPK analysis. It utilize a metal block for drying which can provide uniform heating with zero cross contamination.

Features

Online temperature controlling;

Compatible with most of the 96-well collection plates;

Adjustable height for blower holder;

Digital display and touch screen, simple and friendly operation;

Double heating mode (through bottom plate also N2 airflow.).

Tentative Price 200000 to 2500000 Rupees

Column: Promosil Silica, 4.6×250 mm

Sample: (1) methylbenzene (2) nitrobenzene

(3) o-nitroaniline (4) m-nitroaniline

(5) p-nitroaniline.

Mobile phase: Isooctane:ethanol:water = 85:15:0.3

Flow Rate: 1.00 mL/min

Temperature: Room temperature

Detector: UV 254 nm

Tentative Price : 200000 to 2500000 Rupees

MULTI-SPE M08 is a multi-function manual SPE device designed for routine analytical laboratories with patented technology. This is the first positive pressure SPE manifold that can handle most of the SPE application requirements. Positive pressure is applied to push the sample or solution through SPE cartridges smoothly. It eliminates the differences of the flow-rate between the cartridges that encountered frequently on vacuum SPE devices. Varying from other positive pressure SPE devices, MULTI-SPE M08 is suitable not only for single- cartridge mode but also stacked cartridges mode applications. Another empty sample loading cartridge can be added on the top of the SPE cartridges to meet the bigger sample loading volume requirement. 30 to 50 mL samples can be stored in the sample loading cartridge. Even higher sample loading requirement such as up to 50mL could be achieved by sample loading pipeline which is optional. There are several collection racks are available to fit various collection tubes or flasks. The maximum collection volume is 100 mL for each fraction. A step indicator is installed on the front panel of MULTI-SPE M48 so that the user can mark SPE process step by step.

Tentative Price : 200000 to 2500000 Rupees

MULTI-SPE M96 is a positive pressure manifold, specially designed for height through put sample preparation in research and testing laboratories. It could apply evenly gas pressure on each well to press liquid through 96-well SPE plates smoothly. It largely reduces the variation on the flow-rate between each well of 96-well plates, comparing with vacuum SPE devices, thus improving sample-to-sample consistency. For some viscous samples, vacuum may not provide enough pressure and will cause clogging issue. However, MULTI-SPE M96 can provide maximal 60 psi positive pressure to help the sample pass through 96-well plates with a adjustable flow rate.

Features

◆ Low variation on the flow-rates between wells of 96-well plates which could improve the extraction consistency.

◆ High-throughput by processing maximal 96 samples simultaneously.

◆ Separated tuning to get precisely pressure control.

◆ The SPE stage indicator could be manually switch ed to the indicator position to remember the current stage of your operation.

◆ The whole SPE process can be completed in an inert (N2) environment by choosing N2 gas source.

Tentative Price : 200000 to 2500000 Rupees