Nature of Business
Legal Status of Firm
Sole Proprietorship (Individual)
Manufacturer of spring coiling machine and spring end grinding machine.
The springs manufactured are desired to have certain characteristics which are redetermined.
The major criterion is the load generated by a spring at a specific deflection and the most vital is compatibility of a spring to work for its most desired number of cycles. This test is known as Endurance or Fatigue test.
The Endurance testing machine manufactured by M s SHK Machine Tools are of one station or multiple stations i.e. for testing one sample or multiple samples at a time. These are custom build machines as per once requirements
Most user friendly
Load And Number Of Cycles Displayed Digitally
Machine Stops As Soon As The Sample Fails
Machines Available With Or Without Computer Interface
These decoilers facilitates in continuous and smooth feeding of wire or strip to the machine.
The decoiler unwinds wire or strip only when required by the machine. Decoiler stops as soon as sufficient loop is formed and starts when feeding is essential. Incase of any entanglement or any hindrance the decoiler stops and cuts off the machine preventing accidents or breakage of wire.
The machine is well equipped with proximity switches and solid state control panel.
A vital design criterion of compression and tension spring is the load it creates at a particular deflection. The Spring Load Testing Machine manufactured by M s SHK Machine Tools facilitates to check compression and tension load at desired deflection in same machine. This equipment is most user friendly, robust in construction with digital readouts for deflection and load.
Most user friendly
Load and Deflection displayed digitally on load indicator and digital vernier respectively
Higher accuracy for load and deflection
Motorized unit for higher range of load available
Machines are supplied with calibration certification nationally
traceable to comply ISO standards.
Spring Grinding Machines facilitates in achieving exact ground lengths, with parallel ends, truly square ends, suitable for large or small batches. The duplex wheel construction grinds both the ends simultaneously.
Machines are facilitated with both crush and automatic down feed arrangements.
The important and unique feature of these machines is single solid rigid spindles top and bottom enabling to achieve higher E1 and E 2 values for all models.
Some additional features:
Centralized lubrication for entire machine
Forced air cooling for springs.
Motorised and manual up down movement for bottom wheel for higher
Motors Of standard make viz. Crompton, Kirloakar, etc only and gear
box of Bonfiglioli.
Electrical components of standard make viz. Seimens, LandT etc.
AC Drive of Mistubishi
Imported linear Scale of ELAP
And many more
Neat Cutting Oil is been used for several machining processes such as gear hobbing, broaching, gun drilling, turning on single and multi spindle automats as coolant.
As a result of adhesion and surface tension cutting oil sticks to chips and component. Chips are stored in chip yards where the oil is recovered by gravity, but the oil sticking due to adhesion and surface tension cannot be recovered and thus results in major loss.
The Automatic Oil Extractor manufactured by M s SHK Machine Tools can be used to recover oil form chips positively and has following features
Fully automatic cycle except loading of Chips
Efficiency around 90 95 percent
Removal of dried chips is automatic at the bottom into the trolley after
Every operation saving time and cost of labour
No Skilled Labour is required to operate the machine
Lower maintenance and running cost
Total programmed cycle eliminating human fatigue and error thus very effective
The Oil separated is discharged from the oil outlet
Suitable for chips of Mild Steel, Cast Iron, Aluminum, Brass etc.
Filtration units manufactured by Ms HK Machinery are suitable for solid liquid separation and overcome all limitations of other filtration systems viz. magnetic separator and paper band filters.
These unit works on centrifugal force principal and can be used for both water soluble oil and neat cutting oil for separation of magnetic and non magnetic particles upto 20 microns without any filters. These units have almost no wearable or replaceable parts thus making it very economical for use.
Higher filtration can also be offered with additional modifications.
All units are supplied with additional spare bowl.
· No Consumables
· Suitable for filtration of water soluble and straight cutting oil
· Separation of magnetic and non-magnetic contaminants is possible
· Filtration improves tool life by reducing tool wear
· Filtration up to 20 microns can be achieved
· Filtration extends fluid change interval
· Filtration extends fluid life
· Improves heat transfer
· Improves component finish
· And many more
Long and curly chips or nested chip balls handling is a predicament for shop manager in small and large scale industries.
The Chip Shredder manufactured by M s SHK Machine Tools cuts these long, nested chips into desired small size reducing the volume of chips almost to one third.
Long curly nested chips from machine are to be fed to the chip shredder, the unique cutter arrangement guides the chips to the center cutting them into desired size shredded chips can be achieved as per once requirement .
In case any foreign material or heavy chips balls enter the cutting area causing overload the unit has an facility of detecting such abnormality stopping and reversing for two three times clearing the jam, however in case the jam does not clear the unit stops giving signal buzzer or flashing lamp . In this case the units needs to be attended and cleared manually. This is an unique online overload protection.
Ask For Price
H K Machinery
Industrial Estate, C4, Wagle Estate, Near ITI, Shanti Nagar,
Thane-400604, Maharashtra, India