X
View Mobile Number 87% Response Rate
Send Email

Our Products

29 products available
+View All

FLUID MECHANICS AND HYDRAULIC ENG LAB EQUIPMENTS

Leading Manufacturer of Bernoulli''s Theorem Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment, Major And Minor Losses In Pipe Line Apparatus - Fluid Mechanics And Hydraulic Eng Lab Equipment, Flow Through Mouthpiece & Orifice Apparatus - Fluid Mechanics and Hydraulic Eng Lab Equipment, Orifice Meter Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment, Flow Measurement By Ventur & Orificemeter Apparatus - Fluid Mechanics And Hydraulic Lab Equipment and Helical And Spiral Coils Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment from Chennai.+ Read More

Bernoulli''s Theorem Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

This setup is designed to verify Bernoulli's Theorem experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli's Theorem. The flow rate of water is measured using measuring tank and stop watch provided.

View Complete Details

Yes, I am interested!

Major And Minor Losses In Pipe Line Apparatus - Fluid Mechanics And Hydraulic Eng Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The Set-up consists of a 1/2 bend and elbow, a sudden expansion & sudden contraction fitting from 15 mm to 25 mm, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fitting. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch

View Complete Details

Yes, I am interested!

Flow Through Mouthpiece & Orifice Apparatus - Fluid Mechanics and Hydraulic Eng Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Measurement of flow constitutes an essential part in all flow systems. The fluid flow in open channel definitely requires some system to measure the quantity of fluid passing through, Direct measurement of flow either gravimetric or volumetric is the most accurate method. An apparatus for determination of co-efficient of discharge of orifices and mouthpieces consisting of a storage Tank, Collecting Tank, supply Tank and Pump (0.5 HP) for lifting water. Control valves and measuring instruments like stop clock, scale X-Y coordinate measuring arrangement etc.

View Complete Details

Yes, I am interested!

Orifice Meter Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contains a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rate. Flow rate of water is measured with the help of measuring tank and stop watch

View Complete Details

Yes, I am interested!

Flow Measurement By Ventur & Orificemeter Apparatus - Fluid Mechanics And Hydraulic Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contains a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rate. Flow rate of water is measured with the help of measuring tank and stop watch

View Complete Details

Yes, I am interested!

Helical And Spiral Coils Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Helical coils are used for heating or cooling in process tanks. When a fluid flow through a curved tube, centrifugal force acting upon the various elements of fluid moving with different velocities causes secondary circulation. Secondary flow results in higher heat transfer characteristics. Further secondary flow stabilizes the laminar flow leading of a higher critical Reynolds number for transition from laminar to turbulent flow.

Experiments

·         To determine the critical Reynolds number of a fluid flowing through the coil.

·         To determine the friction factor for flow of water through helical coil

View Complete Details

Yes, I am interested!

Centrifugal Pump Test Rig - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The unit consists of a centrifugal pump provided with variable speed motor. The pump is provided with a vacuum gauge at suction and a pressure gauge on discharge pipe. The pump is provided with a variable speed drive & gate valve at discharge which facilitates estimation of pump performance at various speeds & discharge heads. Power input to motor is measure with energy meter. Specifications: Centrifugal pump:1? x 1? size, with variable speed D. C. motor & speed controller.Sump tank: 900 X 400 X 400 mm.Measuring Tank: 400 X 400 X 400 mm.Energy meter for motor input measurement.Pressure & vacuum gauge for measurement of head.Stop watch.The assembly of pump & control are mounted on the sump tank.1 Hp D.C. motor variable speed type. Services Required: Floor space of 1 m. x 1 m.230 V., 15 A, A. C. supply with earthing connection. Range Of Experiments: Following characteristics can be studied at different speeds Discharge vs. HeadDischarge vs. Input to pumpDischarge vs. pump efficiency

View Complete Details

Yes, I am interested!

Pelton Wheel Setup (Impulse Turbine) - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manfacturer ofLab Equipments
Good QualityGood Service
Colorblue

The unit consist of a small pelton wheel connected to rope brake dynamometer. It is high head at minimum discharge turbine. Water is given from reservoir to the turbine through penstock. A centrifugal pump is provided to supply the water to turbine. Orifice meter & pressure gauges provided to measure flow rate, water jet is directed over the bucket by a nozzle Thus, and we can determine B.H.P. & I.H.P. & various efficiencies

View Complete Details

Yes, I am interested!

Francis Turbine Setup ( Reaction Turbine) - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Country of OriginMade in India
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Specifications:
•Francis turbine 75 mm size to develop 1 Kw at 1250 R.P.M. with a flow of about 1000 L.P. M. at 10 m. Supply head, complete with rope brake arrangement, pressure gauge, vacuum gauges and a set of dead weights etc. for conducting experiments in metric units.•5 Hp Supply pump set 75 mm size, 1000 L.P.M at 14 meters head suitable for supplying water to the above turbine and for operation on 400 V., 3 pH, 50 cycles A.C. mains.•Switch and starter suitable for the above monoblock pump set, mounted on a panel board.•Flow measuring unit consisting of a suitable orifice meter & pressure gauge.•Piping system consisting of pipes, valves, fittings complete with suitable for the test rig.•Fiber Glass Lined M.S. sump to store sufficient water for independent circulation through the unit for experimentation & arranged within the floor space of the main unit.•Rigid mild steel frame work compactly fitted with all the above items as a self sufficient package unit, suitable for operation without any foundation.

View Complete Details

Yes, I am interested!

Kaplan Turbine Setup - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
ColorBlue
BrandElshaddai
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Kaplan turbine designed to develop 1 Hp at 1500 rpm, complete set with a flow of 2200 LPM at 10 mtr. supply head, complete with rope brake arrangement, pressure measuring device.

·         Piping system consisting of pipes and fittings complete set for the kaplan turbine test rig.

·         Flow measuring unit consisting of venturimeter and a double column differential manometer.

·         Supply pump set 7.5 hp for the above consisting of a pump of size 150 mm to discharge 2500 L.P.M at 10 m total head suitable for operation on 3 phase 50 cycles 440 VAC supply.

·         Switch and starter for the above pump set.

·         Rigid mild steel frame work, compactly fitted with all the above items as a self sufficient package

·         unit, suitable for operation without any foundation.Mild steel sump to store sufficient water for independent circulation through the unit for experimentation and arranged within the floor space of the main unit.

A technical manual accompanies the unit.

View Complete Details

Yes, I am interested!

Metacentric Height Of Floating Bodies Apparatus - Fluid Mechanics And Hydraulic Engin Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Determination of the metacentric height  and thus the metacentre  of a floating pontoon.

This is by graphic analysis of the angles of tilt of the pontoon with various centres of gravity.

Determination of buoyancy  centre of buoyancy.

Buoyancy Experiment 

View Complete Details

Yes, I am interested!

Pipe Friction Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service
ColorBlue

The unit consist of two pipes of different diameter. A collect tank is provided to measure the actual discharge.
Features: Testing of two pipes of different diameters.

Measurement of head loss in the pipes at various flow rates. Calculation of pipe friction at various flow rates.
Range Of Experiments: To determine coefficient of friction for pipes. To plot relation between pressure loss and flow rates for a particular pipe diameter

View Complete Details

Yes, I am interested!

Reynold's Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
ColorBlue
BrandElshaddai
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

This set up is designed to verify Reynolds’s Apparatus experimentally. The Apparatus consists of a glass tube with one end having bell mouth entrance connected to a water tank. At the other end of the glass tube a cock is provided to vary the rate of flow. Flow rate of water can be measured with the help of Measuring Cylinder and Stop Watch supplied with the set-up. A capillary tube is introduced centrally in the bell mouth. To this tube dye is fed from a small container, placed at the top of Constant head Tank, through polythene tubing.

View Complete Details

Yes, I am interested!

Triangular Notch And  Rectangular Notch Apparatus - Fluid Mechanics And Hyd Engin Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service
Colourblue
usageLaboratory

The Lab setup consists of a channel having sufficient length and width in which water is supplied from the bottom. Required Notch is fitted at one end of this channel. A hook gauge with Vernier scale is fitted to measure the height of fluid in flow channel. Arrangement for fixing interchangeable notches is made. Set of three brass notches. i.e. rectangular notch. 60V notch & 4SV notch provided along with the set up. Present set up is self contained water re-circulating unit provided with a sump tank and a centrifugal pump etc. Flow control valve and by pass value are fitted in water line to conduct the experiment on different flow rate. Flow rate of water is measured with the help of measuring tank and stopwatch

View Complete Details

Yes, I am interested!

Flow Nozzle Test Rig - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Colorblue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Eqipments
Manufacturer ofLab Equipments
Good QualityGood Service

The apparatus consists of a Nozzle meter. The flow can be regulated by the valve provided at the down stream.Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

View Complete Details

Yes, I am interested!

Rota Meter Setup Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Colorblue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The apparatus consists of three pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice and third pipeline contains a Rotameter. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference.

View Complete Details

Yes, I am interested!

Annular Pipe Flow Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

This set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifuge pump etc. Flow control valve and by-pass valve are fined in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

View Complete Details

Yes, I am interested!

Venturimeter Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

·         The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contains a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rate. Flow rate of water is measured with the help of measuring tank and stop watch.

View Complete Details

Yes, I am interested!

Pitot Tube - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Country of OriginMade in India
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Pitot tube is a small 'L' shaped tube, with both end open. The bend side portion is inserted in the pipe line & the other end is kept open to atmosphere. This end may be connected to a sensitive manometer to measure the head in that plane i.e. path of flow. From this head we can find out the velocity of flow.
Apparatus:
A pitot tube made up of small copper tube is held in a pipe line. A screw type arrangement

View Complete Details

Yes, I am interested!

Friction Factor In Pipes Pipe Flow Analysis Setup - Fluid Mechanics Hydraulic Engineering Lab
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
ColorBlue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

This set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifuge pump etc. Flow control valve and by-pass valve are fined in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

View Complete Details

Yes, I am interested!

Open Drum With Orifice Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

·         The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contains a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rate. Flow rate of water is measured with the help of measuring tank and stop watch.

View Complete Details

Yes, I am interested!

Reciprocating Pump Test Rig - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Usage/ApplicationLaboratory Equipment
BrandElshaddai
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The present Reciprocating Pump Test Rig is a self-contained unit operated on closed circuit basis containing a sump tank. The set-up consists of a Double acting, Single Cylinder Reciprocating Pump coupled with a AC Motor. Flow of water is measured by using measuring tank and stopwatch. Vacuum gauge is fitted on suction line and Pressure gauge is fitted on delivery line to measure the pressure.

Experimentation:

·         To determine the characteristics of reciprocating pump and to find out total head, pump efficiency, overall efficiency & volume metric efficiency.

·         To plot the graph

·         Head Vs Discharge

·         Discharge Vs Pump efficiency

View Complete Details

Yes, I am interested!

Submersible Pump Test Rig - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Colorblue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The unit consists of a Submersible pump provided with constant speed motor. The pump will be provided with a pressure gauge on discharge side pipe. The pump will be submerged in water to about 1.5 to 2 feet so as to cover the suction side. A gate valve is provided at the discharge which facilitates estimation of pump performance at various discharge heads. Power input to motor is measure with energy meter.

Specifications:

·         Submersible Pump 16 stage, 100 mm size inlet & 32 mm outlet, 0.75 Hp. Weight about 30 to 35 Kg.

·         Sump tank.

·         Measuring Tank.

·         Energy meter for motor input measurement.

·         Pressure gauge for measurement of head.

·         Stop watch.

·         The assembly of pump & control are mounted on the sump tank.


Services Required:
 

·         Floor space of 3 m. X 3 m.

·         Tachometer for speed measurement can be supplied.

·         230 V., 15 A, A. C. supply with earthing connection.

View Complete Details

Yes, I am interested!

Gear Pump Test Rig - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
Colorblue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Product Description Gear pumps are positive displacement rotary pumps. The unit is a self contained recirculation type unit. All the measurements are provided to evaluate the performance of the gear pump.Specifications: Gear pump with 1/2 Hp 3 pH motor with three speed cone pulley mounted over the sump tank. Speed 1500 rpm. Discharge measurement tank. Pressure gauge for discharge head. Energy meter for power input. Pressure relevant valve in discharge pipe. Needle valve to control discharge pressure. Range Of Experiments: Following characteristics can be determined Speed Vs Discharge Head Vs Discharge. Discharge Vs Input power. Discharge Vs Efficiency.

View Complete Details

Yes, I am interested!

Impact Of Jet Apparatus - Fluid Mechanics and Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The unit consists of a box with one leak proof transparent side. At the base of the box nozzle can be fitted to supply pipe. The flow can be controlled with a valve. A differential lever with a fine balancing arrangement is provided to measure the force exerts. Plates of different angle can be easily connected to the lever.

View Complete Details

Yes, I am interested!

Free And Forced Vertex Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Country of OriginMade in India
BrandElshaddai
Colorblue
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

Free & Forced Vortex Flow Apparatus
RANGE OF EXPERIMENTS  To visualize the forced & free vortex phenomenon. To plot the shape of vortex profile i.e. vertical height vs horizontal radius.

View Complete Details

Yes, I am interested!

Hydraulic Tilting Flume Test Rig - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
BrandElshaddai
ColorBlue
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

The hydraulic flume should be of size 150mm depth x 250mm wide x 4 meter length built with extra strong 75mm x 50mm. Thickness 4mm through. MS channel b for strength and rigidity. Both vertical sides provided with transparent thick 6mm Perspex for flow visualization at least for 4 meter length. The 16 gauge M.S. Sheet nearly fixed to MS angle frame with rubber packing.The upstream and downstream sections provided with two numbers of fine gates with rack (GM) pinion arrangement for accurate and smooth operation to facilitate the varying the discharge and head water. The sides provided with inverted Tee section (MS) for smooth running of movable hook gauge trolley. The tilting arrangement provided with a fine arrangement which can be operated very smoothly. The slope of the flume ranges up to +5 degree. The tilting arrangement operated by both forward and backward slope settings. For hydraulic different types of experiments the accessories should be incorporated like

 

·         Water tank capacity of size 300 Ltr.

·         Discharge measurement tank of size 60 Ltr.

·         Monoblock Centrifugal Pump2 HP, 3 Phases  (Kirlosker Make)

 

Hook gauge 30cm length fitted on a trolley & arrangement for transverse and longitudinal movement should be supplied. Pipe line to carry water to flume and foot valve at suction end provided.

Centrifugal pump set for supplying water to the flume provided with epoxy painted inside to prevent rust hence increase the life of tank for total rust protection.

8Lockable wheels are provided on all legs.

Experiment Consisting of:

1.      To determine Co-efficient of roughness n for a given flume.

2.      To Calibrate a broad-crested weir and study the pressure distribution at the upstream end of the weir.

3.      To study characteristics of Hydraulic Jump.

To Calibrate a vertical fall and to study the effect of cistern length on the energy dissipation.

View Complete Details

Yes, I am interested!

Pressure Measurement Apparatus - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote
Usage/ApplicationLaboratory
BrandElshaddai
Country of OriginMade in India
ElshaddaiElshaddai Engineering Equipments
Manufacturer ofLab Equipments
Good QualityGood Service

This is a board mounted model which demonstrates various types of pressure measurement devices used in common practice. The devices incorporated are:

 Single well Manometer

·       Differential Manometer

·        Sensitive Manometer

·        Pressure Gauge

·        Vacuum Gauge

These devices are coupled to suction and discharge piping of Hydraulic Bench Pump and a close circulation systems is established, with this set up, the working and operating principle of the pressure measuring devices can be studied

View Complete Details

Yes, I am interested!

Fluidized Bed Set Up - Fluid Mechanics And Hydraulic Engineering Lab Equipment
Interested in this product?
Get Best Quote

Fluidized Bed Set Up - Fluid Mechanics And Hydraulic Engineering Lab Equipment

Rs 65,000 / PieceGet Latest Price

Minimum Order Quantity: 1 Piece

BrandELSHADDAI
Capacity50
MaterialMild Steel
Automation GradeSemi-Automatic
Model Name/NumberELSHADDAI
Batch Size30-50
Voltage220/440V
Usage/ApplicationINSTITUTE
Dimension2MX3M
PowerELECTRIC

Learning Objectives/Experiments

·         To study fluidization characteristics.

·         To study the relationship between the velocity of fluid and pressure drop per unit length.

Scope of Delivery:

1 Self-contained ''''Flow Through Fluidized Bed'''' Apparatus

1 Instruction Manual consisting of experimental procedures, block diagram etc

Additional Information:

  • Item Code: ELSHADDAI-THR-028
  • Production Capacity: 3
  • Delivery Time: TWO WEEKS
  • Packaging Details: WOODEN BOX

View Complete Details

Yes, I am interested!

Get in touch with us

Reach Us

Elshaddai Engineering EquipmentsOld No. 2, New No. 3, S. V. Koil Street, Sekar Nagar elshaddaieeatgmail.com, Ashok Nagar, Chennai-600083, Tamil Nadu, India

Jenny (Admin)

View Mobile Number87% Call Response Rate

Send SMS
Send Email
Send Payment
Leave a Message, we will call you back!
Send your enquiry to this supplier
I agree to the terms and privacy policy

We Accept Online Payments

All Rights Reserved (Terms of Use)