Embedded Design Solutions

Output Voltage	24V DC
Power	50 W
Material	Mild Steel
Input Voltage	4.75 - 23VDC
Color	Green
Conversion Efficiency	95% (5Vin, 3.3Vout ~200mA output)

Mini 360 Step-Down Buck Converter Power Module that uses 4.75V-23V input and 1.0V to 17V output that is configurable using a simple onboard potentiometer. The continuous output current is 1.8A where 3A is the peak or surge current. It uses an integrally melded power inductor that is controlled by a 340kHz switching frequency. It is 95% efficient when driven by a 5V input source and set as 3.3V output at 200mA. This Module provides 30mV output ripple at no load with 0.5% load and 2.5% voltage regulation.

Specification: -

• Regulator IC  :  MPS MP2307DN

• Input Voltage Range :  4.75 – 23VDC

• Selectable Output Voltage   :  1.0 – 17VDC

• Rated Current:  1.8A Continuous and 3A Peak Current

• Maximum conversion efficiency:    95% (5Vin, 3.3Vout ~200mA output)

• Switching Frequency: 340kHz

• No-load output Ripple:  30mV peak to peak

• Load Regulation: 0.5%

• Voltage Regulation   :  2.5%

• Operational Temperature Range:   -40 to +85°C

 

Additional Information:

• Production Capacity: 1000
• Delivery Time: 2-4 days
• Packaging Details: 1 x Embdessol Mini 360 DC-DC Step Down Buck Converter Power Module

Usage/Application	For Automation Use
Brand	Embdessol
Number Of Poles	4 Pole
Surface Finish	Paint Coated
Current Relays	10A - 250 VAC

Relays are important part of any electrical and electronic circuits. We use relays in control applications, switching applications, circuit protection applications and load transfer applications. Relays are also used to provide electrical isolation between two circuits. This 8-channel Relay module comes with Optocoupler protection is an active low relay module which means that the relay will conduct when the input signal falls below 2V and if it is above 2V then the relay is turned off you can also make it an active module by changing the jumper position on the power module. It can be controlled directly with both 3.3V and 5V microcontrollers easily. You can use it to control both DC and AC lines and it also has LED indicators to indicate the state of operation of the module. It also has high Impedance input pin so not to draw any more current than required from the controller.

8-Channel Relay Module Specifications

• Optically Isolated relays protect your microcontroller from damage if the equipment being controlled fails
• 5V 8-Channel Relay Interface Board, each one needs 15 – 20mA Driver current
• Equipped with high current relays 10A which can handle upto 250VAC
• Relay output status indication by LED
• Back EMF Protection
• High Input Impedance

Additional Information:

• Production Capacity: 1000
• Delivery Time: 2-4 days
• Packaging Details: 1 x Embdessol 8 Channel 5V Relay Module with Optocoupler

Usage/Application	For Automation Use
Brand	Embdessol
Number Of Poles	4 Pole
Shape	Rectangle
Relay Module	10
Color	Green

Relays are most commonly used switching devices used in electronics. It can be used to switch high current loads easily unlike transistors which are limited by the maximum current that can flow through them and also can’t switch AC loads. This 5V/3.3V Four Channel 10A Relay Module can switch both AC and DC loads. It is an Electromagnetic switch, when the coil inside is energized with a small current, it can switch ON or OFF the high current circuit. It has PCB screw terminals to directly connect. They can be used in Home automation to switch ON or OFF the appliances, in Electronic circuits to perform switching operations, in safety circuits to disconnect or connect the heavy loads in case of any dangerous situation, in Automobile applications like turning on windscreen wipers, power windows fuel pump, cooling fan etc.

 

Input and output connection:

• This module consist of 4 relay of 5V, and with screw holes.
• IN1, IN2, IN3, IN4 are the input pins of the relay and the output pins are the screw type t-block connectors.
• Connection is NO, COM, NC.
• IT required negative input for the switching.
• It also has over voltage and current protection.
• Reverse voltage protection.
• Consume low current supply.
• Compatible for all type of development boards and also for industrial use.
• Suitable for all types of Arduino boards. 
• More than 20k switching on full load.

Additional Information:

• Production Capacity: 1000
• Delivery Time: 2-4 days
• Packaging Details: 1 x Embdessol Four Channel 5V Relay Module - Made in India

Usage/Application	For Electronic Use
Brand	Embedded Design Solutions
Number Of Poles	4 Pole
Size	180 x 90 x 20mm (L x W x H)
Working voltage	5 Volts
Maximum Current	500mA

This 16 Channel Relay Module consists of sixteen 5V relays and each one of the individual relay needs 15-20mA driver current. This module has a light coupling protection (optocoupler) which provide  opto-isolation for safety purposes. This is a Relay module of 16 channel interface board that can be control various appliances, and other electronic equipment with large current. It can be controlled by Micro-controllers like Arduino, Raspberry-pi, ARM, TTL logic directly. The power supply it has is  LM2596 Power Supply that can control various appliances and other electronic equipment with a large current.

 

Features:

• 5V relay with AC contact capacity of 10A 250V and optocoupler protection.
• Onboard power supply module, doesn't need any external power supply.
• The module can be used as microcontroller development board module and also as appliance control, PLC extended output.
• It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
• The 1-16 road can be any full on/off or any road.
• All interfaces can be directly connected through the terminal leads, very convenient.
• Indication LED’s for Relay output status.

 

Specifications:

• Working voltage: 5 Volts
• Maximum Current: 500 mA
• Low State Voltage: 0 - 0.5 volts (Relay is ON)
• High State Voltage: 3.7 to 5 volts  (Relay is OFF)
• Number of Channel: 16
• Dimension: 180 x 90 x 20mm (L x W x H)
• Weight: 100 g

Additional Information:

• Production Capacity: 1000
• Delivery Time: 2-4 days
• Packaging Details: 1 x Embdessol 16 Channel Relay 5V Module

Usage/Application	For Automation Use
Brand	Embedded Design Solutions
Number Of Poles	2 Pole
Output capacity	120v 12A
Operating current	50mA
Input voltage	5V

Relays are most commonly used switching devices used in electronics. It can be used to switch high current loads easily unlike transistors which are limited by the maximum current that can flow through them and also can’t switch AC loads. This 5V 1A Relay Module can switch both AC and DC loads. It is an Electromagnetic switch, when the coil inside is energized with a small current, it can switch ON or OFF the high current circuit. It has PCB screw terminals to directly connect. They can be used in Home automation to switch ON or OFF the appliances, in Electronic circuits to perform switching operations, in safety circuits to disconnect or connect the heavy loads in case of any dangerous situation, in Automobile applications like turning on windscreen wipers, power windows fuel pump, cooling fan etc.

 

Input and output connection:

1. 3 input male header pin
2. Pin configuration is +,in,-
3. Output or switching pins are NO, CM, NC.
4. Input voltage is 5V
5. Operating current 50mA
6. Output capacity is 250v,7A ,120v 12A or 24VDC,10A
7. Provided Input signal should be negative.

Motor Type	Servo
Number Of Pins	4 Pin
Voltage	24V
Input Voltage	8-35 VDC.
Input Phase	Three Phase
Brand	Embdessol
Model Name/Number	ULN2003

ULN2003 IC is one of the most commonly used Motor driver IC. This IC comes in handy when we need to drive high current loads using digital logic circuits like Op-maps, Timers, Gates, Arduino, PIC, ARM etc. For example a motor that requires 9V and 300mA to run cannot be powered by an Arduino I/O hence we use this IC to source enough current and voltage for the load. This ULN2003 Stepper motor Drive module is used to drive stepper motors, high current LEDs and Relay Modules. This IC utilizes Darlington pair to drive the output and can provide output upto 5V and 500mA. The power required to drive the transistors are taken from the control input hence there is no Vcc pin on the IC.

ULN2003 Stepper Motor Driver Module Specifications

• 7 high-voltage and high current Darlington pairs
• 50V and 500mA for each pair
• Input pins triggering voltage: 5V
• All seven Output pins can be connected to gather to drive loads up to 3.5A
• Low cost and Reliable

Product Description

To use this module you need to connect the input control signals to the controller board you are using. The 5 pin Motor connection for unipolar stepper motor is on the board the module and for any other purposes you can use the output pins on the other side of module. The board is powered by the 5-12V power supply according to your needs from the power supply pins on the module.

Additional Information:

• Production Capacity: 1000
• Delivery Time: 2-4 days