Embeddinator (A Brand Of Engenius Lab)

The A9 development board is a multi-functional development board based on AI-Thinker's A9 GPRS/ GSM module, you can use it to verify the basic communication and peripheral functions of A9 module. It has the basic phone/ SMS, GPRS networking communications.

Wireless Module: ESP32-S WiFi 802.11 b/g/n + Bluetooth 4.2 LE module with PCB antenna, u.FL connector, 32Mbit SPI flash, 4MBit PSRAM.*External Storage: micro SD card slot up to 4GB.

Power your development in the fastest way combine with NodeMCU Firmware. Support WiFi 802.11 b / g / n standard*Wi-Fi Module - ESP-12E module similar to ESP-12 module but with 6 extra GPIOs.*Headers - 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins*USB: Micro USB port for power, programming and debugging,

Compatible with Arduino, MicroPython; Default firmware: lastest MicroPython*For the user for the choice of ESP-12. it doesn't matter. The enhanced version ESP8266-12E is fully compatible with the firmware of ESP-12. It has the additional six pins with IO and SPI ports on the basis of the ESP-12. then develop more convenient.*Chipset: ESP-12E - 802.11 b/g/n, Integrated low power 32-bit MCU; Integrated 10-bit ADC; Integrated TCP/IP protocol stack, TR switch, balun, LNA, power amplifier and matching network, PLL, regulators, and power management units*Supports antenna diversity Wi-Fi 2.4 GHz, support WPA/WPA2 Support STA/AP/STA+AP operation modes Support Smart Link Function for both Android and iOS devices Support Smart Link Function for both Android and iOS devices

The A7670 series is the LTE Cat 1 module which supports wireless communication modes of LTE-TDD/LTE-FDD/m GSM/GPRS/EDGE data transfer rates of up to 10Mbps.

UBlox software for configuration and viewing data can be downloaded from U blox directly*UBLOX NEO-6M GPS Module has a battery for power backup and EEPROM for storing configuration settings. It has also high sensitivity for indoor applications.*The Ublox GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND.*you can apply it on your smart robot car for automatic returning or be heading to a certain destination, making it a real "smart" bot!

The pocket-sized computer transforming the world. Meet the new micro:bit v2, now with an added speaker and microphone for out-of-box audio learning. The hardware also includes a number of technical upgrades to ensure that in the future the device is an ideal tool for exploring, understanding, and experimenting with Artificial Intelligence and Machine Learning, as these technologies begin to transform the planet.

A7670C 4G LTE GSM GPRS Breakout Board supports wireless communication modes of LTE-TDD/LTE-FDD. It supports maximum 10Mbps downlink rate and 5Mbps uplink rate. The A7670 series adopts LGA form factor and is compatible with SIM7000/SIM7070 series, The A7670 series supports multiple built-in network protocols, supports drivers for main operation systems (USB driver for Windows, Linux and Android etc.) and software function, AT commands are compatible with SIM7500/SIM7600 series modules. Meanwhile the A7670 series integrates main industrial standards. Interfaces, with powerful expansibility, including abundant interfaces such as UART

Power your development in the fastest way combine with NodeMCU Firmware. Support WiFi 802.11 b / g / n standard*Wi-Fi Module - ESP-12E module similar to ESP-12 module but with 6 extra GPIOs.*Headers - 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins*USB: Micro USB port for power, programming and debugging,

All Pins are Breakout Pins are available at Female bugs Connector which can be used as main board for developing applications Direct Plug & Play of NODEMCU Lolin, Amica and ESP32 board & run your code.

ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution.*802.11 b/g/n Wi-Fi Direct (P2P), soft-AP, Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)*+19.5dBm output power in 802.11b mode Power down leakage current of <10uA 1MB Flash Memory*Integrated low power 32-bit CPU could be used as application processor SDIO 1.1 / 2.0, SPI, UART STBC, 1×1 MIMO, 2×1 MIMO A-MPDU & A-MSDU aggregation & 0.4ms guard interval

High performance-price ratio small volume, easily embedded to other products strong function with support lwip protocol and freertos supporting three modes: Ap, sta, and ap+sta supporting lua program, easily to develop*Esp32 is already integrated antenna and rf balun, power amplifier, low-noise amplifiers, filters, and power management module*The entire solution takes up the least amount of printed circuit board area this board is used with 24 ghz dual-mode wi-fi and bluetooth chips by tsmc 40nm low power technology, power and rf properties best, which is safe, reliable, and scalable to a variety of applications

Low cost single-chip 2.4ghz GFSK RF transceiver IC,*This wireless Transceiver module is an easy and suitable module if you want to setup your wireless communication system with low cost!! This module can achieve a good balance between wireless transition performance and cost!*When the rate of 2Mbit/s @ 0dBm output,the peak current is 11mA. Power-down mode, power consumption is 400nA. Standby mode, power consumption is 32uA. 130us fast switching and wake time.*With voltage regulator:Oltage regulators on board. Built-in 2.4GHz antenna,support up to six channels of data reception. Low operating voltage: 1.9-3.6V Small size:15*29mm

Quad-band 850/900/1800/1900mhz and Supports 3.0v to 5.0v logic level*TTL serial port, can directly connect to MCU. No need a MAX232*Auto-start ignition, automatic network search On-*board channel indicator light (with slow signal flash, no fast flash signal)

The SIM7670C is Multi-Band LTE-TDD/LTE-FDD/HSPA+ and GSM/GPRS/EDGE module solution in an SMT type which supports LTE CAT1 up to 10Mbps for downlink data transfer. *On board LM317 voltage regulator available for sourcing regulated 5V @ upto 1A voltage to the board and connecting circuit. Extra Berg strip given for GND, +5V & +9V for external connection.*Specially Designed for Various Industrial Projects & Application. Male berg strip given for connection & run properly.*GSM7670C has capability to interface directly with any microcontroller like Raspberry Pi, 8051, PIC, ARM, AVR

• The HM-10 Bluetooth module combines the powerful and programmable Texas Instruments CC2541 Chipset with the required components to start right away with your BLE development. The module offers an on-board voltage regulator and is TTL-level and 5 V tolerant. The Bluetooth-SoC can be accessed via UART interface and supports AT-Commands for setup. It supports full Bluetooth 4.0 standard and can be used for your Arduino or microcontroller to Android or iOS communication projects. This module can be used to replace HC-05, HC-06, and HC-07 devices. This module can also be configured and used as an iBeacon used with Apple devices. 

ESP32 integrates all WLAN and BT functionality in a single package to support a low cost,layout friendly implementation while allowing flexibility for platform specific customization.*It can connect up to 4* Flash/SRAM, each flash should be less than 16 Mbytes. CPU and Memory: Xtensa 32-bit LX6 Dual-core processor, up to 600 DMIPS. 448 KByte ROM 16 KByte SRAM in RTC; 520 KByte SRAM

Manufacturer: A7670C-LNNV Manufacturer: Simcom Limited Supply Voltage: 3.4 ~ 4.2VDC Firmware upgrade: USB/FOTA SIM Card: 1.8/3.0 V

On board LM317 voltage regulator available for sourcing regulated 5V @ upto 1A voltage to the board and connecting circuit. Extra Berg strip given for GND, +5V & +9V for external connection.*Specially Designed for Various Industrial Projects & Application. Male berg strip given for connection & run properly.*GSM900A has capability to interface directly with any microcontroller like Raspberry Pi, 8051, PIC, ARM, AVR

Wireless Module: ESP32-S WiFi 802.11 b/g/n + Bluetooth 4.2 LE module with PCB antenna, u.FL connector, 32Mbit SPI flash, 4MBit PSRAM.*External Storage: micro SD card slot up to 4GB.

Transmitter Module employs a crystal-stabilized oscillator, ensuring accurate frequency control for best range performance*Range in open space (Standard Conditions) : Low power and good range (100m-150m) Meters,*Receiver sensitivity as high as -110dbm compatible with ht12e ht12d packed in anti-static packet to protect during handling*No requirement of external RF components except Antenna RX Supply Current: 3.5 mA. RX Typical Sensitivity: 105 Dbm

Operating voltage: DC12V Working frequency: 315MHZ Remote control distance: 50~ 100m Shock resistance: 270K Operating Current: 10mA

This is 125KHz RFID Card used for Contactless transmission of data and supplies energy with no battery needed. Its Operating distance is Up to 100mm depending on antenna geometry. Operating frequency is 125KHz and Data transfer speed is 106 kbit/s. It is featured with Data integrity of 16 Bit CRC, parity, bit coding bit counting which allows Anti-collision. These cards are typically used in ticketing transaction: <100 ms including backup management. Applications : Public transportation Access control Event Ticketing Gaming & identity Features: Contactless transmission of data and supply energy (no battery needed) Anticollision EEPROM 1Kbit, organized in 16 sectors, each district two passwords User definable access conditions for each memory block Data retention of 10 years. Write endurance 100 000 cycles Security Individual key set per sector (per application) to support multi-application with key hierarchy A unique serial number for each device Transport key protects access to EEPROM on-chip delivery Package includes: 1 x 125KHz RFID Card – 5Pcs.

13.56 MHz RFID Proximity Cards for Attendance and Access Control This is a 13.56 MHz RFID Card used for Contactless transmission of data and supplies energy with no battery needed. Its Operating distance is Up to 100mm depending on antenna geometry. The operating frequency is 13.56 MHz and the Data transfer speed is 106 kbit/s. It is featured with Data integrity of 16 Bit CRC, parity, bit coding bit counting which allows Anti-collision. These cards are typically used in ticketing transactions: <100 ms including backup management. APPLICATIONS : Public transportation Access control Event Ticketing Gaming & identity Features: Contactless transmission of data and supply energy (no battery needed) Anticollision EEPROM 1Kbit, organized in 16 sectors, each district two passwords User-definable access conditions for each memory block Data retention of 10 years. Write endurance 100 000 cycles Security Individual key set per sector (per application) to support multi-application with key hierarchy A unique serial number for each device Transport key protects access to EEPROM on-chip delivery

Espressif ESP32-WROOM-32D 4M 32Mbit Flash WiFi Bluetooth Module

ESP32-WROOM-32D and ESP32-WROOM-32U are powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming, and MP3 decoding.
ESP32-WROOM-32U is different from ESP32-WROOM-32D in that ESP32-WROOM-32U integrates a U.FL connector. For detailed information on the U.FL connector please see Chapter 10 in the datasheet attached. Note that the information in this data sheet is applicable to both modules. Any differences between them will be clearly specified in the course of the document in the attachment.

Note: For All Technical details go through the datasheet in the attachment

This WiFi relay module carries an ESP8266 WiFi module and microcontroller. It will send the serial port instructions to the cell phone APP and Implementation within the local area network (LAN) for wireless control relay.

This module is ideally suited to controlling larger voltages in your project through WIFI. This is a 2 channel relay module that can be used to activate up to 250V AC and 30V DC. This allows you to build in device control, operating remote lights, or triggering

ESP32 integrates all WLAN and BT functionality in a single package to support a low cost,layout friendly implementation while allowing flexibility for platform specific customization.*It can connect up to 4* Flash/SRAM, each flash should be less than 16 Mbytes. CPU and Memory: Xtensa 32-bit LX6 Dual-core processor, up to 600 DMIPS. 448 KByte ROM 16 KByte SRAM in RTC; 520 KByte SRAM