Description:
Chryso Proof  Acrylic is  acrylic polymer based elastomeric,waterproofing protective coating system. In addition to UVresistance acrylic polymer, Chryso Proof Acrylic is  designedwith  alkali-acid resistance micro-fibre enhance tensile strengthproprietary additives to resistpost growth of algae and fungusand  selected pigments reduces surface temperature up to 15°Cwhen exposed to direct sun light.The thixotropic nature of thecoating helps to apply thick film to getdesired film thickness (1 to1.5mm) with minimum no of coats.
Method of Application:Surface Preparation:
Prior to application of Chryso Proof  Acrylic, all surfaces mustbe prepared properly to avoid failure. The surface shall be cleanedto remove all dust, foreignmaterial/loose particles or any depositof contaminants, which could affect the bond between theoriginal substrate and the Chryso Proof  Acrylic system. Thiscan be done by scarifying, grinding, water blasting, acid washingor any other approved method. Rectify depression / honey-comb(if any)in the surface, use Chryso Armourcrete mortar (1part Chryso Armourcrete,  2 part  cement, 4 part medium washedsand) and leave it for at least 24  hours  before  application  of Chryso Proof Acrylic.
Treatment of Cracks:
If there is any crack up to 2 mm, cleanthose cracks with vacuumcleaner,  to  open  cracks,  pour Chrysoproof  Acrylic primer followed by a coat of Chryso Proof Acryli Calong the crack lineand leave it to dry for overnight.

• UV Resistance- does not yellowing in sun rays exposure
• Reduces cooling and heating demand.
• Save energy and utility costs by maintaining temperature inside the room.
• Excellent resistance to carbon dioxide, acid rain, and alkali solution.

• Chryso Thermoshield is pure acrylic polymer  based elastomeric high build solar heat reflecting eco-friendly paint for roof and exterior walls. The cooling effect is designed  with high quality titanium di oxide pigment which reflects more than 80% of solar radiation and specialty micronized ceramic hollow sphere  which  reduces  heat  transmission  inside  the  room.  The cured Chryso Thermoshield also  acts as high performance waterproof membrane.When it is applied on exterior side wall sand roof it reduces energy cost approximately 30%.

• After the application primer coat allow it to reach touch dry for 2-3  hours. Stir Chryso Thermoshield to  a homogeneous smooth consistency and apply it  horizontally with soft nylon brush, roller or squeeze to thickness of 125-150 microns in single coat. Allow it to dry for approx. 4-5 hours. When the applied coat  becomes sufficiently dry (no foot print observed) apply second coat vertically. Two coats are sufficient for general application (150-200 microns DFT) but for  severe  conditions,three or more coatsare required to achieve desired results.

• Chryso Thermoshield is used for heat insulation and waterproofing of old as well as new flat / slope concrete /metal roof, terrace and walls of residential, commercial and industrial buildings.

• Prior to application of Chryso Thermoshield,  all  surfaces must be prepared properly to avoid failure. The surface shall be cleaned to remove all dust, foreign materials/loose particles or any deposits of contaminants,  which  could  affect  the  bond between the original substrate and the Chryso Thermoshield system. This can be done by   scarifying,grinding, water  blasting,  sand  blasting, acid  washing  or  any other approved method. Rectify depression / honey-comb  (if any) in the surface, use Chryso Armourcrete mortar ( 1 part Chryso Thermoshield ,2part cement, 4 part medium washed sand)  and  leave  it  for  at  least  24  hours  before  application  of Chryso Thermoshield.

Polyurethane

Other Details:

Crystalline coating

Anti Carbonation

Description:
Agent for old concrete to new concreteand repair mortar.
Chrysota pelastic is a two component, elastomeric, acrylicpolymer modified cementitious waterproofing protectivecoating system in slurry form.

Method of Application:
Surface Preparation:
Prior to application of Chrysota pelastic, all surfaces must beprepared properly to avoid failure. Thesurface shall be cleanedto  remove  all  dust,  foreign  materials/loose particles or anydeposits of contaminants,which could affect the bond betweenthe original substrate and the Chrysota pelastic system. Thiscan be done by scarifying, grinding, water blasting, sandblasting, acid washing or any other approved method. Rectifydepression / honey-comb (if any) in  the surface, use Chrysota pelastic Chrysormourcrete mortar before application of Chrysota pelastic.

Mixing:
Chryso Tapelasticliquid  PART(polymer)  is  mixed  withPOWDER PARTin the ratio of 1:2.5 by weight with a help of lowspeed  (300-400  rpm)  paddle  mixer.  The  mix  has  to  be  stirredthoroughly, until a lump-free smooth slurry is obtained. Standfor 4-5 minutes after mixing to release air from the mix.