Good Morning Paints Private Limited

Additional Information:

• Delivery Time: 3
• Packaging Details: Available in 20 Ltr Packs Only

• STELLYN can be added to into concrete either in batching plant or mixing trucks as per the dosage by consultant
• It is recommended that STELLYN is added into batching plants lastly into concrete and through mixing for 5 to 10 minutes is envisaged
• The amount of water to be determined only after carrying out mix since STELLYN also has water reduction property along with crystallisation
• Water is an important agent to form crystalline process. Initially water will access to concrete through porous portion of concrete. STELLYN will then react with water and crystallisation process initiates 

Additional Information:

• Packaging Details: STELLYN Crystalline Integral Waterproofing Admixture Unlike any other organic admixture STELLYN is a hydraulic waterproofing compound and being inorganic fully compatible with cementitious materials The cementitious matrix has lot of capillary voids in concrete. These are responsible for leakage as well as deterioration at a later stage once the water pressure in the capillaries build up The inorganic chemical group in water STELLYN will react with water and insoluble crystalline products are generated throughout the capillary pores of concrete This crystalline product is highly resistant to water and perform very well even under extreme conditions such as pressure or aggressive chemicals attack Application: STELLYN can be added to into concrete either in batching plant or mixing trucks as per the dosage by consultant It is recommended that STELLYN is added into batching plants lastly into concrete and through mixing for 5 to 10 minutes is envisaged The amount of water to be determined only after carrying out mix since STELLYN also has water reduction property along with crystallisation Water is an important agent to form crystalline process. Initially water will access to concrete through porous portion of concrete. STELLYN will then react with water and crystallisation process initiates

• Drill 20mm holes into the concrete to a depth of 25mm and insert the Powrthrow caplets into it. Seal it off with EPCO^®-1010
• Spacing of Powrthrow caplets can be,
  For Columns - 1 unit per RMT from 2 opposite faces in staggered fashion
  For Beams - 1 unit RMT from 2 opposite faces in staggered fashion
  For Slabs - ln 1mt x 1mt grid insert 4 units
• Seal it off with EPCO^® -1010

Additional Information:

• Packaging Details: POWRTHROW Sustained Release Caplet for Corrosion Protection of Existing RCC Structures The reduction of service life of any RCC structure is basically due to corrosion of rebar. This process is very severe when structures are exposed to marine or chemical atmosphere. Powrthrow is an unique solution for maintaining the integrity of existing RCC structure from corrosion of rebar. By introducing Powrthrow into the concrete structures, the rate of corrosion of rebar reduces significantly & the release of active ingredient is over a considerable period of time. METHOD OF APPLICATION Drill 20mm holes into the concrete to a depth of 25mm and insert the Powrthrow caplets into it. Seal it off with EPCO®-1010 Spacing of Powrthrow caplets can be, For Columns - 1 unit per RMT from 2 opposite faces in staggered fashion For Beams - 1 unit RMT from 2 opposite faces in staggered fashion For Slabs - ln 1mt x 1mt grid insert 4 units Seal it off with EPCO® -1010 Note: For site specific applications the spacing can be designed separately

• Thoroughly clean the substrate with the coarse wire brushes and wipe the dust, cementatious incrustation etc with a clean cloth or compressed air. Remove curing compound grease etc using clean water and detergents
• Apply by brush or spray
• Avoid application during high winds and hot hours especially in summers
• Subsequent coating can be applied immediately
• Keep the container away from direct heat or sunlight

Additional Information:

• Packaging Details: Monopol 456 S Silane Siloxane Penetrative Primer for Concrete and Masonry Monopol®-456-S consists of reactive hydrophobic silane-siloxane with a very high degree of penetrative action. It works by penetrating into the pores of concrete and reacting with the existing water vapour to form hydrophobic polysiloxane lining to the pore capillaries. Application Procedure Thoroughly clean the substrate with the coarse wire brushes and wipe the dust, cementatious incrustation etc with a clean cloth or compressed air. Remove curing compound grease etc using clean water and detergents Apply by brush or spray Avoid application during high winds and hot hours especially in summers Subsequent coating can be applied immediately Keep the container away from direct heat or sunlight

• Mix CORROSEAL Base & Curing agent in prescribed proportion by volume and allow it to remain for 10 minutes before application. Apply 2-3 coats of Corroseal with a time interval of 24 hours between coats

Additional Information:

• Packaging Details: CORROSEAL CORROSEAL is a two pack polyamide cured air drying epoxy compound. CORROSEAL has excellent resistance to corrosion. Application Procedure Mix CORROSEAL Base & Curing agent in prescribed proportion by volume and allow it to remain for 10 minutes before application. Apply 2-3 coats of Corroseal with a time interval of 24 hours between coats

• Surface preparation is an essential part of the application. It is necessary to clean and dry the concrete surface prior to use
• The concrete cracks or honeycombed surfaces shall be chipped to a minimum depth of 10mm in right angle to surface or as per requirement. The areas to be repaired shall be profiled to get rectangular or square shape with a right angle edge of 10mm
• Refer Technical datasheet for mixing
• Use it for gravity pouring / flooding within scheduled pot life
• Curing in air for 3-6 hours before allowing traffic to pass
• Follow stitching, stapling or grouting procedure whenever needed
• Repeat the same procedure for pot hole filling in concrete pavements, culverts and bridges and for levelling the surface as a wearing coat

Additional Information:

• Packaging Details: MONOPOL 160 High Molecular Weight Polymer / Mortar MONOPOL®-160 is a low viscosity high molecular weight thermosett polymer. Due to its low viscosity, cracks and honeycombs are filled upto full depth of concrete RCC / concrete roads. Application Procedure Surface preparation is an essential part of the application. It is necessary to clean and dry the concrete surface prior to use The concrete cracks or honeycombed surfaces shall be chipped to a minimum depth of 10mm in right angle to surface or as per requirement. The areas to be repaired shall be profiled to get rectangular or square shape with a right angle edge of 10mm Refer Technical datasheet for mixing Use it for gravity pouring / flooding within scheduled pot life Curing in air for 3-6 hours before allowing traffic to pass Follow stitching, stapling or grouting procedure whenever needed Repeat the same procedure for pot hole filling in concrete pavements, culverts and bridges and for levelling the surface as a wearing coat

Additional Information:

• Delivery Time: 5
• Packaging Details: EPMORT-350 Ready to use epoxy mortar system EPMORT-350 is a two component prefilled epoxy mortar system comprising of a resin component (Part A) and a hardner component (Part B)

EPCO-KP HP 250 Low Viscosity Epoxy Injection System

It is a low viscosity epoxy resin systemcomprising of RESIN : KP-250 andHARDENER : HP-250. This system has anexcellent bond with the concrete structures andby virtue of its low viscosity it can penetrate intothe finer cracks present in the concrete.

Additional Information:

• Production Capacity: 500000
• Delivery Time: 5
• Packaging Details: It is a low viscosity epoxy resin system comprising of RESIN : KP-250 and HARDENER : HP-250. This system has an excellent bond with the concrete structures and by virtue of its low viscosity it can penetrate into the finer cracks present in the concrete.

Additional Information:

• Packaging Details: KARAIKOTE®–6545 is a uniquely formulated high performance coating material recommended for applications on moist and dry surfaces of concrete and steel. KARAIKOTE®-6545 is manufactured under technical know-how from Central Electrochemical Research Institute, Karaikudi.

Additional Information:

• Delivery Time: 2
• Packaging Details: 20

Additional Information:

• Delivery Time: 3
• Packaging Details: SiFumex®-100-D Natural Amorphous Microsiliceous Admixture It is a well-established fact that siliceous admixture used as an essential component of concrete can impart significant enhancement to the basic properties of concrete in both the fresh and hardened state. Typical Application An admixture in high performance concretes Chemical resistant concrete and mortar in Effluent and Sewerage treatment plants, Industrial floorings, Pothole repairs, Bridges, Girders, etc. Waterproofing of Water Tanks, Terraces, Basements, Walls and in all concrete structures. As waterproofing additive in brickbat coba Addition Add SiFumex®-100-D to dry ingredients of concrete

• Mix Monobond^® in water first prior to addition in cement mortar / concrete. Dosage 10% to 15% by weight of cement.

Additional Information:

• Delivery Time: 3
• Packaging Details: Monobond Monobond® is a polymer latex additive for modifying cement concrete / mortar / plaster / grouts. The addition of Monobond® improves mechanical properties especially flexure and tension. Due to low permeability of polymer modified systems, remarkable improvement in prevention of carbonation, chloride ion penetration is observed. Also chemical resistance improves significantly. The addition of Monobond® imparts resilience to the cement matrix. Thereby improving impact resistance. Also the modified cement matrix cures in air, eliminating the necessity of wet curing. It is necessary to mix Monobond® in water first prior to addition in cement mortar I concrete. Application Procedure Mix Monobond® in water first prior to addition in cement mortar / concrete. Dosage 10% to 15% by weight of cement.

• Increased workability or reduction in water to cement ratio for durable and cohesive concrete
• Increase of early and final strength
• Retains slump for placing & pumping of concrete

• To achieve flowing concrete
• To achieve higher workability
• Good slump retention

• Add SUPERCON^®-300 to concrete mix after dispersing in water

Additional Information:

• Packaging Details: SUPERCON 300 Superplasticizer for High Workability & Slump Retention SUPERCON®-300 is a superplasticizer, which when added to concrete offers the following advantages. Increased workability or reduction in water to cement ratio for durable and cohesive concrete Increase of early and final strength Retains slump for placing & pumping of concrete Typical Application: To achieve flowing concrete To achieve higher workability Good slump retention Mixing: Add SUPERCON®-300 to concrete mix after dispersing in water

• Thoroughly remove the spalled concrete and loose material. Abrade / clean the rusted steel mechanically. Spray EPCO-KP-100 along the exposed concrete surface in the vicinity
• After few minutes wipe the concrete/steel surface with moist cloth to remove residual material from the surface. The inhibitor by now has already penetrated the concrete. Follow up with application of bond coat and subsequently with repair mortar / concrete / plaster
• In case of application for preventive maintenance, abrade the concrete surface mechanically to remove loose particles, incrustations, residual oil, grease etc. Remove existing paint if the surface is already painted, by abrading
• Spray EPCO-KP-100 over entire concrete surface.
• Keep the container tightly closed in a cool place. Wear safety goggles during spraying

Additional Information:

• Packaging Details: EPCO KP 100 Concrete Penetrating Corrosion Inhibitor (CPCI)® EPCO-KP-100 is a hi-tech corrosion inhibition system that works on the Bipolar Inhibition Mechanism (B.I.M.). B.I.M. inhibits corrosion of the steel in concrete at the poles, cathodic & anodic simultaneously. EPCO-KP-100 by virtue of its high vapour pressure & affinity for the embedded metal diffuses through the densest concrete to reach the corroding steel. Upon deposition on the rusted steel substrate, EPCO-KP-100 molecules prevent further reaction between the steel and chloride/oxygen thus arresting the corrosion process. Application Procedure Thoroughly remove the spalled concrete and loose material. Abrade / clean the rusted steel mechanically. Spray EPCO-KP-100 along the exposed concrete surface in the vicinity After few minutes wipe the concrete/steel surface with moist cloth to remove residual material from the surface. The inhibitor by now has already penetrated the concrete. Follow up with application of bond coat and subsequently with repair mortar / concrete / plaster In case of application for preventive maintenance, abrade the concrete surface mechanically to remove loose particles, incrustations, residual oil, grease etc. Remove existing paint if the surface is already painted, by abrading Spray EPCO-KP-100 over entire concrete surface. Keep the container tightly closed in a cool place. Wear safety goggles during spraying Dosage Rate: 4 sq.mt./lt. Spray repeatedly over the area as to dose the required quantity. Dense concrete may require repeated application, while porous substrate would absorb immediately.

• To obtain good adhesion it is necessary to have a clean and sound substrate, which can be obtained by grinding, wire brushing, chipping, sandblasting, etc.
• Mix EPIBOND-21-LP thoroughly in the prescribed proportion and apply on the clean and sound substrate
• Apply concrete / cement plaster / gunite on the tacky EPIBOND-21-LP layer which would be achieved approximately after 30 minutes of application and within two hours
• Best results are obtained when w/c ratio of the new concrete is as low as practicable

Additional Information:

• Delivery Time: 3
• Packaging Details: EPIBOND-21-LP Bonding Agent with long pot life EPIBOND-21-LP is used to bond fresh concrete to concrete that is fully cured. EPIBOND-21-LP will give monolithic bond capable of transmitting high stresses. In addition, EPIBOND-21-LP possesses excellent water and alkali resistance and has long tackfree time of 120 minutes. This would help in laying concrete/mortar even after 120 minutes of application of bond layer. Application Procedure To obtain good adhesion it is necessary to have a clean and sound substrate, which can be obtained by grinding, wire brushing, chipping, sandblasting, etc. Mix EPIBOND-21-LP thoroughly in the prescribed proportion and apply on the clean and sound substrate Apply concrete / cement plaster / gunite on the tacky EPIBOND-21-LP layer which would be achieved approximately after 30 minutes of application and within two hours Best results are obtained when w/c ratio of the new concrete is as low as practicable

• Mix Part A(EPCO^®KP-350) and Part B (EPCO^®HP-350) in the ratio of 2:1 by weight in a clean plastic container
• Stir thoroughly for 5-10 minutes so as to achieve a uniform mix
• Add component C-Graded Quartz filler slowly and mix thoroughly to achieve a uniform mortar mix
• The mortar (A+B+C) after mixing shall be used within 30 minutes hence it is ideal for mixing small quantity at a time
• Before application of mortar the surface to be primed with bond coat of KP-350:HP-350 neat epoxy coating (Part A:Part B in 2:1 by weight)
• It is important to clean, degrease and abrade the substrate thoroughly before applying the bond coat using mechanical wire brushes

Additional Information:

• Packaging Details: EPCO®KP-350 + EPCO®HP-350 epoxy mortar is a three-component system with non-shrink and high mechanical strength properties. Application Procedure Mix Part A(EPCO®KP-350) and Part B (EPCO®HP-350) in the ratio of 2:1 by weight in a clean plastic container Stir thoroughly for 5-10 minutes so as to achieve a uniform mix Add component C-Graded Quartz filler slowly and mix thoroughly to achieve a uniform mortar mix The mortar (A+B+C) after mixing shall be used within 30 minutes hence it is ideal for mixing small quantity at a time Before application of mortar the surface to be primed with bond coat of KP-350:HP-350 neat epoxy coating (Part A:Part B in 2:1 by weight) It is important to clean, degrease and abrade the substrate thoroughly before applying the bond coat using mechanical wire brushes

• All areas of application shall be free from oily residues, dust and loose particles
• Corroded reinforcement shall be cleaned thoroughly and treated with anti-corrosive coating Feovert^® & IPNet^®-RB
• The substrate to be treated shall be wetted with clean water (Saturated surface dry condition) prior to placement

• Use 25kgs of Molith^® MC SILVER bags once opened. Pour mixing water gradually into Molith^® MC SILVER in a standard mixer until required consistency is achieved. Using planetary mixer is desired for optimum performance. For 25kgs mix water requirement will be typically 3.0 to 4.0 ltrs. For larger volumes use concrete mixer 

Additional Information:

• Delivery Time: 3
• Packaging Details: Molith MC SILVER Free flow, shrinkage compensated, high strength microconcrete Molith® MC SILVER is a free flow, shrinkage compensated, single component micro concrete used in high volume repairs of concrete structures. Application Methodology: All areas of application shall be free from oily residues, dust and loose particles Corroded reinforcement shall be cleaned thoroughly and treated with anti-corrosive coating Feovert® & IPNet®-RB The substrate to be treated shall be wetted with clean water (Saturated surface dry condition) prior to placement Mixing: Use 25kgs of Molith® MC SILVER bags once opened. Pour mixing water gradually into Molith® MC SILVER in a standard mixer until required consistency is achieved. Using planetary mixer is desired for optimum performance. For 25kgs mix water requirement will be typically 3.0 to 4.0 ltrs. For larger volumes use concrete mixer