Gurit India Private Limited

Spabond adhesives offer outstanding performance in numerous composite and non-composite bonding applications, and perfect partners for Gurit laminating products. Spabond adhesives offer ease of use, durability and a consistently high quality. 
The Spabond range is supplied in various formats to suit different requirements. For smaller volume projects cartridge applicators provide perfectly mixed adhesive to the joint, cleanly and with a minimum of waste. For larger volume applications Spabond adhesives can be mixed and dispensed using a range of mixing machines.      

MAIN FEATURES
¬ High strength and toughness adhesive, with excellent gap filling properties
¬ Range of working times / clamp times
¬ 2:1 mix ratio (by weight and volume)
APPLICATIONS
¬ Bonding of hull-to-deck, bulkheads and frames

MAIN FEATURES
¬ High performance adhesive
¬ High strength gap filling adhesive
¬ Range of working times
¬ 2:1 mix ratio (by volume)
APPLICATIONS
¬ Bonding of hull-to-deck, bulkheads and frames

MAIN FEATURES
¬ Excellent gap filling properties
¬ High strength and toughness
¬ Range of working times
¬ 2:1 mix ratio (by volume and weight)
¬ Temperature performance up to 84°C APPLICATIONS
¬ Ideal for bonding large structures where surfaces have uneven geometry

MAIN FEATURES
¬ Low density (0.7 S.G.) core bonding paste
¬ Long working time for large structures
¬ Easy to sand
¬ Can be used for strip planking with wood or foam strips
APPLICATIONS
¬ Suitable for applications where lightweight core is used

MAIN FEATURES
¬ Suitable for bonding polyester and epoxy parts
¬ Sag resistance up to 30mm on a verticle surface
¬ Wide range of hardeners, from fast to extra slow
¬ Low exotherm and shrinkage in thick bond lines
APPLICATIONS
¬ Ideal for stringers and bulkheads
¬ Ideal for frames and hull-to-deck joints on medium t

MAIN FEATURES
¬ Fast curing, low toughness non-structural adhesive
¬ Ideal when used as an 'extra hand' in assembly
¬ 5 minute adhesive
¬ 1:1 mix ratio (by volume and weight)
APPLICATIONS
¬ General bonding and repair work on a wide range of materials

MAIN FEATURES
¬ Reduced clamp time structural adhesive
¬ Available in 400ml x 2 component dual cartridges
¬ Gels in 10 minutes, solid in two hours
¬ Full properties after an overnight cure at ambient
APPLICATIONS
¬ Fit-out
¬ Finishing
¬ Repair

Gurit Hi-Panels offer customers ease and speed of build, reduced set up and labour costs, and high quality construction of their composite part.
Hi-Panels are epoxy infused composite panels, which can be made from a variety of Gurit’s core materials, with glass and/or carbon skins, and are either structurally engineered by the company’s in-house team or manufactured to the customer’s specification.
They are suitable for a range of applications such as the structural elements of sailing yachts or power boats, hatch lids, doors and so on.
Hi-Panels can be delivered as finished panels, with maximum dimensions of 9m x 2m, or cut to shape, as supplied by the customer. The shapes can be labelled, and remain tabbed in the original panel for ease of transportation and storage.

As the technical leaders in commercial composite materials, Gurit offers a complete range of composite tooling products for the marine market.  

Each product is designed as part of a complete tooling solution, with properties optimised for the intended application.  

Gurit's tooling product range consists of a tooling paste designed for pattern manufacture and a range of ambient curing mould materials that can be used up to an operating temperature of 130°C / 265°F.

REINFORCEMENTS CATEGORIES Gurit supplies an extensive range of reinforcements suitable for composite component manufacture and repair. These materials are based on the most widely used fibre types and fibre orientations and incorporate a variety of construction techniques in their manufacture.
The range of Reinforcements is presented by fibre type:
¬ E-Glass Products
¬ Carbon Products
¬ Aramid Products
¬ Hybrid combinations of the above fibres
Reinforcements are also sub-divided into the following categories, based on the orientations of the primary structural fibres:
¬ Unidirectional Fabrics ¬ Woven Fabrics
¬ Multiaxial Fabrics & Tapes  
REINFORCEMENT NOMENCLATURE 1st Letter: General Construction of Reinforcement Fabric
¬ WR = Woven rovings - (glass)
¬ R = Woven fabric - yarn (glass/aramid) or tows (carbon)
¬ X = Double bias (±45°) stitched fabric ¬ Q = Quadraxial (0°/90°/±45°) stitched fabric
¬ Y = Triaxial (0°/±45°) stitched fabric
¬ UT = Unitex woven low-crimp unidirectional fabric
¬ UF = Unifibre non-woven unidirectional fabric

2nd Letter: Fibre Type (or Major Component in Hybrid)
¬ E = E glass
¬ S = S glass (or R glass)
¬ A = Aramid
¬ C = Carbon
3rd letter: 2nd Fibre Type - Minor Component in Hybrid (as above); also: (when present) T = Tape version                 Following the letters are 2, 3 or 4 digits which provide an indication of area weight in g/m2. (Please note that the number shown in the fibre style is not the exact weight in grammes.
Final digit: Identifier to distinguish otherwise similar fabrics.
Suffix letter: For woven fabrics, the following suffixes indicate the weave
¬ P = Plain
¬ T = 2x2 twill
¬ S = 3x1 twill
¬ T4 = 4x4 twill
¬ Hx = Satin (where x = harness number)
¬ C = Crowsfoot
¬ B = Basket
¬ Q = Quadran  
VACUUM CONSUMABLES The Airtech range of vacuum consumables has been designed for use in a wide variety of vacuum bag processes. Such processes include autoclave / prepreg curing, wet lay-up, low temperature oven / prepreg processes and infusion processes.
Gurit has selected a specific range of products which are particularly suitable for working with epoxy prepreg and laminating systems where they are regularly used for the curing of large composite structures at temperatures up to 150°C / 300°F.
                     ANCILLARIES Gurit supplies a range of ancillary products, including: Solvents, Filler Powders & Sundries