Hi Q Test Equipment Private Limited

Model Name/Number

HIQ-5107

     Comprises of Auto Transformer (6A), 3nos. Voltmeter (300v) and 3 nos. Ammeter (2A), Rheostate (50Ohms/1.5A), Choke (15omH@1.5A), on/off switch with fuse unit, 4mm Terminals (15A) mounted on heavy duty powder coated sheet metal front panel with Schematic/wiring diagram printed. Fitted in a self standing rugged design cabinet suitable for stand alone operation.

Features:

• This unit allows the user to measure the total current in the supply and current through Resistor load & current through inductor load seperately.
• User manual and 4mm patch cords supplied.

Accessories Included:

• 3 Phase Resistor & Inductor Load Banks Are Provided Along With The Unit.

Model Name/Number

HIQ-5109

Features:
The kit comprises of the following:

• +/- 10mm LVDT calibrated Jig with micrometer accuracy : 1%.
• Display unit consists of built in regulated DC power supply, Excitation RMS voltage source, Signal conditioner, Bridge Amplifier, A to D converter & 3  1/2 Digit, display to indicate displacement directly in mm.
• Zero & span adjustments done through pot controls provided on the front panel.
• Test points and controls brought out on the panel with schematic circuitry printed. 

Specification Range: +/-10.00mm or +/-25.00mm or +/-50.00mm; Excitation RMS voltage:1v-2v@2KHz; Accuracy: 1%; 3 1/2 digit, display to indicate displacement in mm; Sensitivity: 0.1 mm; Repeatability: 1%; mains operating voltage:230v;50Hz.

• User manual and Patch cords supplied.

Model Name/Number

HIQ-5110

The kit comprises of following:

• Calibrated Jig-1 Cantilever stainless steel beam fitted with four  strain gauges, pan and weights upto 1kg.(100 gms X 10 nos).
• Display unit -1 consists of built in regulated DC power supply, beam excitation voltage, signal conditioner, bridge Amplifier and 3&half  digit, display to indicate the microstrain in the beam.
• Zero and span adjustments done through pot controls provided on the Front Panel.
• Test Points, Controls brought out on the panel with schematic circuitry printed.        

Specifications Beam: Stainless stell material, dim:300(I)*28(b)82.5(t)mm;        Capacity:1 kg; Strain Guage: Foil type Resistance, 350SL, Q.L3mm;                           Bridge excitation voltage: 10v DC; Unit operating voltage:230v, 50Hz.

Model Name/Number

HIQ-5100

 Comprises of Auto Transfomer 6(A),Voltmeter(300V),Ammeter(5A), Wattmeter(1500W), Energy meter, Resistor 50Ohms/5A-2 ; 50Ohms/2.5A-1, Choke (0-150mH-300mH@ 1.5A), Capacitor   15uf-2; 30uf-2, Fuse with on/off Switch unit, 4mm Terminals (15A) mounted on heavy duty powder coated sheet metal front panel with schematic/wiring printed. Fitted in a self standing rugged design cabinet suitable for stand alone operation.
Features:

• The trainer is provided with high quality calibrated Wattmeter (1500W) and Ammeter(5A) to enable the student to calibrate the 1 Phase Energy Meter.
• Ammeter and Wattmeters of heavy duty are provided in the trainer to cover reasonably high loads.
• In addition to calibration of energy meter the student can calculate active and reactive components of power separately.
• User manual and 4mm Patch cords supplied.

Accessories Included:-

• Resistive, inductive, Capacitive loads are internally provided to study pure Resistive, Leading PF and Lagging PF loads.

Model Name/Number

Hi Q-5103

consist of Precision grade Kelvin Double Bridge unit, DC power supply continuously variable and galvanometer desk top type supplied along with the unit.

Features:

• This Unit is supplied with highly regulated DC Power source to operate the unit.
• Resistors used in the trainer for coarse and fine adjustments are of high Stability standard material made of Manganin.
• It provides the students to measure the unknown resistance close to a value of 1 micro ohms. The schematic/wiring diagram printed on the panel to follow and conduct experiments.
• User manual and 4mm Patch cords supplied.

Accessories included: DC Power supply and Galvanometer necessary for conducting experiments are provided alongwith the unit (No additional equipment required)

Kelvin Double Bridge For Measurement Of Low Standard Resistor

Model Name/Number

HiQ-5106

Measurement Of 3phase Reactive Power With Single Phase Wattmeter:

• Comprises of Voltmeter (500v), Ammeter (5A), Wattmeter (3Kw), Resistor 1K Ohms/2A -3nos. , Choke (0-300mH-300mH @1.5A) -3nos. , Capacitor 30uF/400v -3nos.. On/Off Switch with fuse unit, 4mm Terminals (15A) mounted on heavy duty powder coated sheet metal front panel with Schematic/wiring diagram printed. Fitted in a self standing rugged design cabinet suitable for stand alone operation. 

Features:

• This Unit is provided with high quality calibrated watt meters of 3KW range, AC ammeter of 0-5A.
• The student can measure reactive power flowing into Load. Necessary variable balanced Resistor/Capacitor/Inductor load banks are provided along with this unit.
• User manual and 4mm Patch cords supplied

Accessories included: Necessary Resistive, Capacitive, Inductive loads are internally provided to Conduct experiment
(No additional equipment required).

Additional Information:

• Item Code: HiQ-5106

Model Name/Number

HIQ-5108

A.C.BRIDGE:-It consists of four arms of impedance, a sinewave generator, Detector or Headgear set. The sine wave generator is provided with frequency selection switch from 1KHz to 40KHz. Low frequency signal is used for measuring primary inductance (Lp) and high frequency for secondary inductance (Ls). Thus by measuring primary and secondary inductances of transformer with A.C bridge, the turns ratio is decided.

Features:

• In this unit, a wide range of capacitors are provided to cover different ranges of Primary and secondary windings of transformer.
• The user can easily measure Inductance of any winding by choosing proper capacitor & resistor value in the bridge.
• User manual & 4mm patch cords supplied.

ACCESSORIES: Signal generator, Galvanometer/pair of headphones Transformers (samples) are provided internally for conducting experiments.

Model Name/Number

HiQ 5109

LVDT Trainer Module

Experiment:Measurement of displacement using LVDT
The Kit comprises of the following:>+/-10mm LVDT calibrated Jig with micrometer accuracy: 1%>Display Unit consists of built in regulated DC power supply,Excitation RMS voltage source ; Signal conditioner, Bridge, Amplifier,A to D converter & 3 1⁄2 Digit, display to indicate displacementdirectly in mm>Zero and span adjustments done through pot controls provided on theFront panel>Test points and controls brought out on the panel with schematic circuitryprinted

Specifications:

• Range: +/-10.00mm or +/-25.00mm or +/-50.00mm 
• Excitation RMS voltage: 1v-2v @ 2KHz 
• Accuracy: 1% ; 3 1⁄2 Digit,Display to indicate displacement in mm 
•  Sensitivity: 0.1 mm 
• Repeatability: 1% 
•  Mains operating voltage: 230v 
• 50Hz>User manual and Patch cords supplied(No external equipment required)

Model Name/Number

HiQ 5108

Comprises of Maxwell’s Inductance-Capacitance bridge. With inbuilt 1KHz sine wave Generator, Galvanometer/pair of headphones, DC power supply. Features:
In this unit, a wide range of capacitors are provided to cover different ranges of Primary and secondary windings of transformer.
The user can easily measure Inductance of any winding by choosing proper capacitor and resistor value in the bridge. User manual and 4mm Patch cords supplied. 

Accessories included: Signal generator, Galvanometer/pair of headphones, Transformers (samples) are provided internally for conducting experiments (No additional equipment required)

Transformer Turns Ratio Measurment Using A.C.Bridge (Maxwel)

Model Name/Number

HiQ-5104

Features:

• Provided with builtin DC power source and 1KHz Sine wave generator.
• Different ranges of components provided in the trainer to measure wide range of component values with these bridges.
• A pair of head phones, User manual and 4mm Patch cords supplied.

Accessories included: Sine wave generator, Head phones along with 5nos. unknown Capacitor are Provided in the unit to conduct experiments. (No additional equipment required)

Model Name/Number

HIQ 5105

Features:

• Provided with builtin DC power source and 1KHz Sine wave generator.
• Different ranges of components provided in the trainer, to measure wide range of component values.
• A pair of head phones, User manual and Patch cords supplied.

Accessories included: Necessary DC source, 1KHz Signal source and other bridge components And inductors are provided in the unit (No additional equipment required)

Model Name/Number

HIQ-5105

Features:

• Provided with builtin DC Power source and 1KHz sine wave Generator.
• Different ranges of components provided in the trainer, to measure wide range of component values.
• A pair of headphones, user manual & patch chords will supply.   Accessiries included: Necessary DC source, 1khz signal source and other bridge components and inductors are provided in the unit.

Model Name/Number

HIQ-5101

Rheostate (150Ohms/50Ohms; 2A), Voltmeter (300v), Ammeter (5A), Wattmeter (1500W), power Factor (0.5-1-0.5), Choke (0-150mH-30mH@1.5A-1; Capacitor 30uf-2; 15uf-1; Fuse with on/off switch unit, 4mm Terminals (15A) mounted on heavy duty powder coated sheet metal front panel with Schematic/wiring diagram printed. Fitted in a self standing rugged design cabinet suitable for stand alone operation.

Features: 

•  The unit is provided with necessary meters of high ratings of power & current along with necessary load banks of Inductive, Resistive & Capacitive.
• This enables the user to study the effects of various loads on phase angle in AC circuits.
• User manual & 4mm patch cords will supply.                                                     Accessories Included:Inductive,Capacitive and Resistive load on phase banks are internally provided.

Model Name/Number

HIQ-5104

The Schering Bridge one of the most important AC bridges, is used extensively for the measurement of capacitors. Although the Schering Bridge is used for capacitance measurements in a general sense, it is particularly useful for measuring insulating propertics i.e., for phase angles nearly 90⁰.

Features:

• Provided with builtin DC power source & 1KHz Sine Wave Generator.
• Different ranges of components provided in the trainer to measure wide range of component values with these bridges.
• A pair of headphones, user manual and 4mm Patch cords supplied.

Accessories included: Sine Wave generator, Headphones along with 5nos. unknown Capacitor are provided in the unit to conduct experiments.

Model Name/Number

HiQ-5110

Experiment:

• To measure strain in metal conductor using Strain gauge Bridge The Kit comprises of the following: Calibrated Jig -1 Cantilever stainless steel beam fitted with four strain gauges, pan and weights upto 1Kg.(100gmsX10nos.) Display Unit -1 Consists of built in regulated DC power supply, beam excitation voltage, Signal conditioner, Bridge, Amplifier and 3 ½ digit, display to indicate the Microstrain in the beam. Zero and span adjustments done through pot controls provided on the Front panel.
• Test points, Controls brought out on the panel with Schematic circuitry printed    

Model Name/Number

HiQ-5100

Comprises of Auto Transformer (6A), Voltmeter (300V), Ammeter (5A), Wattmeter (1500W), Energy meter, Resistor 50Ohms/5A – 2 ; 50Ohms/2.5A – 1, Choke (0150mH-300mH@ 1.5A, Capacitor 15uF – 2 ; 30uF – 2 Fuse with On/Off Switch unit, 4mm Terminals(15A)mounted on heavy duty powder coated sheet metal front panel with Schematic/wiring diagram printed. Fitted in a self standing rugged design cabinet suitable for standalone operation.

Features:

• The trainer is provided with high quality calibrated Watt meter (1500W) and Ammeter (5A) to enable the student to calibrate the 1phase Energy meter.
• Ammeter and Watt meters of heavy duty are provided in the trainer to cover reasonably high loads.
• In addition to calibration of Energy meter the student can calculate active and reactive components of power separately. >User manual and 4mm Patch cords supplied

Accessories Included: Resistive, Inductive, Capacitive loads are internally provided to study pure Resistive, Leading PF and Lagging PF loads.

Model Name/Number

HiQ-5102

     Consist of Crompton DC potentiometer with built in coarse & fine controls, Stabilized power supply unit, volt ratio box, low resistance sensitive galvanometer desk top type supplied along with the unit.

Features:

• This trainer is supplied along with highly regulated DC Power Supplies to operate the unit.
• Further to calibrate PMMC meters, necessary ratio boxes also provided.
• Resistors used in this Unit for coarse and fine are very standard type made of manganin.
• This enable the user to measure the potential in a circuit close to micro volts.
• Necessary schematic/wiring diagram printed on the panel to follow and conduct experiments.
• User manual and 4mm Patch cords supplied.

Accessories included: Necessary DC Power supplies, Ratio boxes & Galvanometer are provided Alongwith the unit.