Jay Agenciez

Devcon Plastic Steel Putty A

Description: Devcon Plastic Steel Putty is a steel-filled epoxy putty that cures at room temperature and is designed for filling, rebuilding, and bonding metal surfaces.

Intended Use: Devcon Plastic Steel Putty is a Patching and repairing areas where welding or brazing would be undesirable or impossible

Product features: Devcon Plastic Steel Putty Applies easily to vertical surfaces, Machinable to metallic finish, Bonds to aluminium, concrete, and many other metals, Resistant to chemicals and most acids, bases, solvents, and alkalis.

Technical Properties of Devcon Plastic Steel Putty
Colour Grey
Mix Ratio by Volume 2.5:1
Mix Ratio by Weight 9:1% Solids by Volume 100
Pot Life @ 75F 45 min.
Specific Volume 11.9 in.(3)/lb
Cured Shrinkage 0.0006 in./in.
Specific Gravity 2.33 gm/cc
Temperature Resistance Wet: 120 Degrees F; Dry: 250 Degrees F
Coverage/lb 48 sq. in 1/4 in
Cured Hardness 85D
Dielectric Strength 30 volts/mil
Dielectric Constant 37.5
Adhesive Tensile Shear 2800 psi
Compressive Strength 8260 psi
Modulus of Elasticity 8.5 x 10(5) psi
Flexural Strength 5600 psi
Coefficient of Thermal Expansion 48 [(in)/(in) x F)] x 10(-6)
Thermal Conductivity 1.37 (cal x cm) / (sec. x cm(2) x C) x 10 (-3)
Cure Time 16 hrs
Recoat Time 10-12 hrs
Mixed Viscosity Putty

Test Conducted :
Cure Shrinkage ASTM D 2566
Adhesive Tensile Shear ASTM D 1002
Dielectric Strength, volts/mil ASTM D 149
Dielectric Constant ASTM D 150
Flexural Strength ASTM D 790
Compressive Strength ASTM D 695
Cured Hardness Shore D ASTM D 2240
Coef. of Thermal Expansion ASTM D 696
Thermal Conductivity ASTM C 177
Modulus of Elasticity ASTM D 638

Application Instructions : Spread mixed material on repair area and work firmly into substrate to ensure maximum surface contact. Plastic Steel
Devcon Putty A fully cures in 16 hours, at which time it can be machined, drilled, or painted.
Place fiberglass sheet, expanded metal, or mechanical fasteners between repair area and Plastic Steel Putty A prior to application.

Additional Information:

• Delivery Time: Ex Stock

Devcon Brushable Ceramic Blue

Description :

Devcon Brush able Ceramic putty is brush able, high-performance ceramic-filled epoxy for sealing, protecting and repairing surfaces subject to erosion. Intended Use of Devcon Brush able Ceramic: Seal and protect new equipment exposed to erosion and corrosion; protect pump casings, impeller blades, gate valves, water boxes, and fan blades; rebuild heat exchangers, tube sheets, and other water circulating equipment; top coat for providing exceptionally smooth surface to repaired surfaces. Features of Devcon Brush able Ceramic : Excellent chemical resistance, Temperature resistance to 350 Degrees F, Applies easily with short - bristle brush or roller, Low viscosity, self - levelling liquid. Limitations of Devcon Brush able Ceramic : None

Features of Devcon Brush able Ceramic: Excellent chemical resistance, Temperature resistance to 350Degrees, Applies easily with short - bristle brush or roller, Low viscosity, self - levelling liquid.

Limitations: None

Properties Devcon Brushable Ceramic :

% Solids by Volume 100
Pot Life @ 75F 40
Coeff of Thermal Expansion ASTM D 696
Coverage/lb 7.6 sq.ft./lb mils ( 0.15in.)
Thermal Conductivity 1.92 [(cal. x cm) x degree centigrade C)] x 10 (-3) Brush Coat Thickness 10-20 mils (.010-.020 in.) Cure Time - 16 hr Recoat Time: 4-6 hr

Chemical resistance of Devcon Brush able Ceramic is calculated with a 7 day, room temp. cure ( 30 days immersion @ 70 degrees Degrees Fahrenheit ) Benzene -Excellent
Sodium Hydroxide 10% - Excellent
Gasoline (Unleaded) - Excellent
Sodium Hydroxide 50% -Excellent
Kerosene - Excellent
Sulphuric 10% - Very good
Mineral Spirits - Excellent
Sulfuric 50% - Fair
Nitric 50% - Poor
Toluene - Excellent
Phosphoric 10% - Very good
Xylene - Fair
Potassium Hydroxide 40% - Excellentz

Devcon Underwater Wet Surface Repair Putty :

Description :

Devcon Underwater Wet Surface Repair Putty Makes (effective) repairs to metal, concrete, wood surfaces in wet and dry environments.Intended Use: Repairing and refitting pipes, valves, pumps, and tanks. Repair concrete vessels and piping in wet environments.

Devcon Wet Surface Repair Putty product will bond to a wet or damp surface.

Devcon Wet Surface Repair Putty features: Bonds to aluminum, concrete, and many other metals Bonds to ferrous and non-ferrous metals Non-rusting Bonds to wet surfaces Bonds, patches, and seals metals Non-sagging

Limitations :

Typical Physical Properties : Technical data should be considered representative or typical only and should not be used for specification purposes.

Cured 7 days @ 75 degrees farenheight.

For best results, product should be kept and applied at room temperature.

Bronze Putty can be applied when temperatures are between 13 degrees centigrade and 52 degrees centigrade. Spread Bronze Putty over prepared surface with a putty knife. Press firmly to ensure maximum surface contact and avoid trapping air. To bridge large gaps or holes use fibre glass, sheet metal or wire mesh.

Specification :

Color - Grey
Mix Ratio by Volume 1:1
Mix Ratio by Weight 1.4:1% Solids by Volume 100 Pot Life 75F 45 min.
Specific Volume 17 in.(3)/lb. Cured Shrinkage 0.0020 in./in. Specific Gravity 1.4 gm Temperature Resistance Wet: 120 Dry: 250
Coverage/lb 68 sq.in./lb. 1/4" Cured Hardness 82 Shore D
Dielectric Strength 150 volts/mil Dielectric Constant 8.6
Adhesive Tensile Shear 2,685 psi Compressive Strength 5,625 psi Modulus of Elasticity 7.5 psi x 10(5) in. Flexural Strength 4,990 psi Coefficient of Thermal Expansion 18 x 10 Cure Time 24 hour Recoat Time 10-12 hour Mixed Viscosity Putty

For Underwater or submerged repairs consider the following:- Remove all dirt, barnacles, flaking paint, and algae/seaweed from the substrate.- Wipe area with a clean cloth to remove any film on the surface. Obviously you cannot degrease underwater, but wipingand turning a clean cloth often will remove any film on the surface.- Abrade the surface if possible. (Use mechanical means or a file to accomplish.)- The oxidation can be removed by mechanical means, such as water, grit-blasting, or by chemical means.- Make the repair as soon as possible to avoid surface contamination.

Ammonia -Very good, Chlorinated Solvent - Poor, Hydrochloric 10% - Fair, Kerosene - Very good, Methanol - Poor , Sodium Hydroxide 10% - Very good, Sulfuric 10% - Fair, Toluene - Very good,

Additional Information:

• Delivery Time: Ex Stock

Wear Resistant Putty WR

Devcon Wear Resistant Putty Intended Use: Devcon Wear Resistant Putty is used For repairing flange faces, machine ways, valve seats and bodies, and tracing guides

Devcon Wear Resistant Putty Product features: Devcon Wear Resistant Putty is Rebuilds and protects interfacing metal surfaces, Protects metal from bi-metallic corrosion, Repairs metals and concrete.

Devcon Wear Resistant Putty Limitations: Not recommended for long term exposure to concentrated acids or to organic solvents 

Typical Physical Properties: Technical data should be considered representative or typical only and should not be used for specification purposes

Tests Conducted:

Adhesive Tensile Shear ASTM D 1002
Cure Shrinkage ASTM D 2566
Dielectric Strength, volts/mil ASTM D 149
Dielectric Constant ASTM D 150
Modulus Degrees Fahrenheit Elasticity ASTM D 638
Compressive Strength ASTM D 695
Cured Hardness Shore D ASTM D 2240
Coef. Degrees Fahrenheit Thermal Expansion ASTM D 696
Flexural Strength ASTM D 790
Thermal Conductivity ASTM C 177

 Surface Preparation:
Thoroughly clean the surface with Devcon Cleaner Blend 300 to remove all oil, grease, and dirt.
Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increased surface area for better adhesion (Caution: An abrasive disc pad can only be used provided white metal is revealed).
Desired profile is 3-5 mil, including defined edges (do not "feather-edge” epoxy).

Note: For metals exposed to sea water or other salt solution, grit-blast and high-pressure-water-blast the area, then leave overnight to allow any salts in the metal to “sweat” to the surface. Repeat blasting to “sweat out” all soluble salts.

Other Details:
Perform chloride contamination test to determine soluble salt content (should be no more than 40ppm).
Clean surface again with Devcon Cleaner Blend 300 to remove all traces of oil, grease, dust, or other foreign substances from the grit blasting.
Repair surface as soon as possible to eliminate any changes or surface contaminants.

 Fill: .0625″ – .075″Color: Red Mix Ratio: 3.4:1

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Devcon Titanium Putty

To serve our clients requirement, we are engrossed in providing optimum quality Devcon Titanium Putty.

Devcon Titanium Putty is a high-performance, non-rusting titanium-reinforced epoxy is engineered for making repairs to machinery and equipment that can be precision machined.

Moreover, Devcon Titanium Putty can withstand heavy loads in hard chemical environments.

Features:Devcon Titanium Putty has an Excellent temperature resistance (3500F)Devcon Titanium Putty has a High compressive strength (18,800 psi)Devcon Titanium Putty has a Resistance to chemicals and most acids, bases, solvents, and alkali.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Production Capacity: 1
• Delivery Time: Ex Stock
• Packaging Details: Stander Packing

Devcon Titanium Putty

Product Description:
Devcon Titanium Putty is a high performance, titanium reinforced epoxy engineered for making critical repairs to machinery and precision parts
Features and Benefits:
Temperature resistance to 176 Degrees Centigrade
Excellent chemical resistance
Compression strength of 124 MPa
Qualifies under mil spec DOD-C-24176B
Non-rusting, machinable to metallic finish
Restore bearing housings and scored shafts
Rebuild wear rings, hydraulic rams and valves
Repair equipment and parts that require a machined finish

Typical Physical Properties Cured 7 days @ 24
% Solids by Volume: 100
Cured Shrinkage ASTM D2566: 0.0010 cm/cm
Pot life at 24oC (0.5kg mass): 21 minutes
Compressive Strength ASTM D695: 129.8 MPa
Adhesive Tensile Shear ASTM D1002: 13.8 MPa
Cured Hardness Shore D ASTM D2240: 87D
Dielectric Strength, volts/mm ASTM D149: 2205

Temperature Resistance:
Wet 66 Degrees Centigrade/ Dry 177 degrees centigrade
5% Bleach (Sodium Hypochlorite) - E, 10% Phosphoric Acid VG
5% Trisodium Phosphate - E, 10% Sulphuric Acid F
10% Sulphuric Acid - E, 10% Sodium Hydroxide E
50% Sulphuric Acid – E, 50% Sodium Hydroxide E
10% Hydrochloric Acid – E, 5% Alum (Aluminium Sulphate) E
0% Nitric Acid – U, 10% Acetic Acid - U
KEY: E = Excellent, VG=Very Good, F-Fair, Unsatisfactory

_{Devcon Titanium Putty are very good in water, saturated salt solution, leaded gasoline, mineral spirits, ASTM #3 Oil and propylene glycol. Epoxies are generally not recommended for long term exposure to concentrated acids and organic solvents}

Surface Preparation for Devcon Titanium Putty: Proper surface preparation is essential to a successful application.

Devcon Stainless Steel Putty

Devcon Stainless Steel Putty is A stainless steel-filled epoxy for rebuilding and repairing stainless steel equipment. 

Repairs cracks, dents, and breaks in stainless steel machinery or castings; rebuilds dairy equipment; Repairs stainless steel holding tanks. Acceptable for use in meat and poultry plants. 

Machinable to metallic finish. NSF Approved (Certified to ANSI/NSF61). Resistant to chemicals, most acids, bases, solvents, and alkalis. 

Not recommended for long term exposure to concentrated acids or to organic solvents.

Devcon Stainless Steel Putty Compliances: Acceptable for use in meat and poultry plants. Certified for potable water application, NSF Approved (ANSI/NSF61), 1/94

Technical data should be considered representative or typical only and should not be used for specification purposes.

Adhesive Tensile Shear - 2,385 psi

Coefficient Degrees Fahrenheit Thermal Expansion - 34 [(in.) / (in). x F) ] x 10(-6)

Colour Dark Grey

Coverage/lb- 50 sq.in. /lb. @ 1/4"

Cure Time - 16 hr

Dielectric Constant - 75

Mix Ratio by Volume - 3.75:1

Mix Ratio by Weight - 11:1

Modulus of Elasticity - 8.0 psi x 10(5) in.

Pot Life @ 75F - 58 min.

Recoat Time - 2-4 hr

Solids by Volume - 100

Temperature Resistance - Wet: 120 Degrees ‚ F; Dry: 250 Degrees ‚ F

Thermal Conductivity - 1.23 [(Cal x cm)/(sec x cm(2)

Tests Conducted on Devcon Stainless Steel Putty

Devcon Stainless Steel Putty Compressive Strength is ASTM D 695

Cured Hardness if Devcon Stainless Steel Putty is Shore D ASTM D 2240

Dielectric Constant of Devcon Stainless Steel Putty is ASTM D 150

Modulus of Elasticity of Devcon Stainless Steel Putty is ASTM D 638

Adhesive Tensile Shear of Devcon Stainless Steel Putty is ASTM D 1002

Cure Shrinkage of Devcon Stainless Steel Putty isASTM D 2566

Dielectric Strength of Devcon Stainless Steel Putty in, volts/mil ASTM D 149

Coef. of Thermal Expansion of Devcon Stainless Steel Putty is ASTM D 696

Flexural Strength of Devcon Stainless Steel Putty is ASTM D 790

Thermal Conductivity of Devcon Stainless Steel Putty is ASTM C 177

Additional Information:

• Production Capacity: 100
• Delivery Time: 1 Day
• Packaging Details: Stander Packing

Devcon Bronze Putty BR

Bronze filled epoxy for repairing, rebuilding and maintaining bronze parts and equipment, Repairs cracks, dents and breaks in equipment, machinery or castings, Rebuilds parts and equipment, Rebuilds shafts, trays and chutes, Repairs to food processing equipment
Description of Devcon Bronze Putty: Bronze filled epoxy for repairing, rebuilding and maintaining bronze parts and equipment.

Recommended Applications of Devcon Bronze Putty:  Repairs cracks, dents and breaks in equipment, machinery or castings, Rebuilds parts and equipment , Rebuilds shafts, trays and chutes, Repairs to food processing equipment.

Chemical Resistance for Devcon Bronze Putty

7 days room temperature cure (30 days) - Testing carried out 30 days immersion at 21 Degrees Centigrade.

Excellent = +/- 1% weight change
Very Good = +/- 1-10% weight change
Fair = +/- 10-20% weight change
Poor = > 20% weight change

Product Data Of Devcon Bronze Putty

Typical Physical Properties :
% Solids by Volume 100
Pot life at 25degrees centigrade/ mins 35
Specific Volume CC/Kg 447
Temperature resistance / degrees centigrade Dry 121 degrees centigrade
Coverage 894cm2/Kg @ 5mm
Cured Hardness / Shore D 85 D
Dielectric Strength KV/mm 1
Adhesive Tensile Shear / MPa 18
Compressive Strength MPa 59
Coefficient Degrees Farenheight Thermal Expansion x10-6 cm/cm/C 59.
Thickness per Coat / mm As Functional Cure Time /Hours 16

Mixing : Bronze Putty is formulated to be a dense mix that can be applied easily to overhead and vertical surfaces without running or sagging. Add the hardener to the resin and mix thoroughly on a mixing board using a spatula. Do not mix in the containers.

Application : For best results, product should be kept and applied at room temperature. Bronze Putty can be applied when temperatures are between 13 degrees centigrade and 52 degrees centigrade. Spread Bronze Putty over prepared surface with a putty knife. Press firmly to ensure maximum surface contact and avoid trapping air. To bridge large gaps or holes use fibre glass, sheet metal or wire mesh.

Additional Information:

• Delivery Time: Ex Stock
• Packaging Details: 500 gms

Devcon Aluminium Putty F

Description: Devcon Aluminium -filled epoxy putty for dependable non rusting repairs to aluminium castings, machinery, and equipment widely used in HVAC applications.

Intended Use : Devcon Aluminium Putty is a Patch for aluminium castings; make jigs, dies, and holding fixtures.

Product features: Devcon Aluminium Putty Can be machined, drilled, or tapped using conventional metalworking tools Bonds to aluminium, concrete, and many other metals Fills voids or pores in castings.

Limitations: Devcon Aluminium Putty is Not recommended for long term exposure to concentrated acids and organic solvents.

Typical Physical Properties: Technical data should be considered representative or typical only and should not be used for specification purposes Cured 7 days 75 Degrees Fahrenheit.
Mix Ratio by Volume - 4:1 Mix Ratio by Weight - 9:1 % Solids by Volume - 100 Pot Life 75degrees 60 min Specific Volume 17.5 in. (3) /lb Temperature Resistance Wet: 120F; Dry: 250degrees 
Coverage/lb - 70 sq.in. /lb. 1/4" Cured Hardness - 85D
Coefficient Degrees Fahrenheit Thermal Expansion - 29 [(in.)/(in). x F)] x 10(-6)
Thermal Conductivity 1.73 [(Cal x cm)/(sec x cm(2) x C)] x 10(-3)
Cure Time - 16 hrs
Recoat Time - 10-12 hrs
Mixed Viscosity - Putty
Test Conducted:  Compressive Strength ASTM D 695
Cured Hardness Shore D ASTM D 2240
Dielectric Constant ASTM D 150
Modulus of Elasticity ASTM D 638
Cure Shrinkage ASTM D 2566
Adhesive Tensile Shear ASTM D 1002
Dielectric Strength, volts/mil ASTM D 149
Coef.of Thermal Expansion ASTM D 696
Flexural Strength ASTM D 790
Thermal Conductivity ASTM C 177
Application Instructions: Spread mixed material on repair area and work firmly into substrate to ensure maximum surface contact. Devcon Aluminium Putty F will fully cure in 16 hours, at which time it can be machined, drilled, or painted. FOR BRIDGING LARGE GAPS OR HOLES Place fiberglass sheet, expanded metal, or mechanical fasteners between repair area and Devcon Aluminium Putty F prior to application.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Production Capacity: 1
• Delivery Time: Ex Stock

Devcon Flexane 80 Rubber Putty

Description: Devcon Flexane 80 is a Trowel able urethane for repairing and lining process equipment exposed to wear, impact, abrasion, vibration, and expansion / contraction.

Intended Use: Devcon Flexane 80 is a Repair and rebuild conveyor belts Line process equipment to dampen noise, Line concrete control joints. Cast flexible molds, fixtures, and parts Pot and encapsulate .Product features: Trowels on smoothly Cures to tough, medium-hard rubber (Shore 87A)

Flexane 80 Putty Chemical Resistance : Chemical resistance is calculated with a 7 day, room temp. cure (30 days immersion) @ 75 Degrees F)
1,1,1-Trichloroethane - Poor
Aluminium Sulphate 10% - Very good
Cutting Oil - Fair
Gasoline (Unleaded) - Poor
Hypo chloric 10% - Very good
Hydro chloric 36% - Very good
Isopropanol - Poor
Methyl Ethyl Ketone - Poor
Phosphoric 10% - Very good
Potassium Hydroxide 40% - Very good
Sodium Hydroxide 50% - Very good
Sodium Hypo chlorite - Very good
Xylene - poor

Other Details :

TESTS CONDUCTED on Devcon Flexane 80 Putty
Tensile Strength (Urethanes) ASTM D 412
Dielectric Strength, volts/mil ASTM D 149
Cured Hardness Shore D ASTM D 2240
Cure Shrinkage ASTM D 2566
Tear Resistance ASTM D 624
Maximum Elongation ASTM D 412

Surface Preparation for Application of Devcon Flexane 80 Putty :

For METAL SURFACES, thoroughly clean area to be repaired, rebuilt, or lined with Devcon Cleaner Blend 300. Remove any oil, grease, or dirt. Roughen surface by grinding with a coarse wheel or an abrasive disc pad. To prime this surface, apply a coat of Devcon FL-10 Primer and allow to dry tack-free for 15 minutes. If the metal surface requires maximum tear resistance or is exposed to moisture, or if submerged in water, use Devcon FL-10 and Devcon FL-20 Primer.


For RUBBER SURFACES, thoroughly clean area with an abrasive pad and Devcon Cleaner Blend 300. Surface can also be roughened with a grinding wheel so that it is coarse and free from oil and dirt that may clog the "pores" of the rubber. Wipe or roughen surface with Cleaner Blend 300 until the cloth no longer picks up the colour of the rubber. The rubber should appear new or deeper in color. To prime this surface, apply a coat of Devcon FL-20 Primer and allow to dry tack free for 15-20 minutes. Use Devcon FL-40 Primer on "hard-to-bond" rubber surfaces as this gives ultimate peeler asistance. Multiple coats may be necessary for porous rubber surfaces. For MAXIMUM ADHESION, sandblast the surface with an angular abrasive until a minimum depth profile of 2-3 mils is met. Blast to near-white finish specification SSPC-SP5 (Steel Structure Painting Council). Prime surface immediately after sandblasting to prevent oxidation.

Additional Information:

• Production Capacity: 100
• Delivery Time: Ex Stock
• Packaging Details: 500 gms