Kwick Fix Solutions

KWICKSEAL AT200 is cold- applied, flexible, rubberized Bitumen based sealing tape.

It is a two layered 1.5mm Polymer Bitumen waterproofing layer with an aluminun foil

to protect the material from impacts of UV radiation & to products the adhesion of sealed

elements.

The Bottom Side KWICKSEAL AT is covered with an easily removable protective film.

KWICKSEAL AT is a convenient way to seal various cracks & joints.

It can also be used to insulate junctions for roofing repairs.

KWICKSEAL AT is specially designed for sealing substrates like matels, concrete, wood,

• Shrinkage –non-shrink even after curing, prevents from cohesive & adhesive failure on exposure.
• Application – applied as one time filling (does not require second time application, as required in other acrylic sealants).
• User friendly – One pack, very soft paste, easily applicable by fingers or putty knife.
• Sagging – non-sag nature helps in filling of vertical & overhead cracks.
• Sanding – no sanding is required.
• Staining – Does not migrate any liquid component into concrete surface thus prevents staining.
• Adhesion – excellent adhesion to cementitious surfaces prevents water leakages through the cracks.
• Durability – UV & weather resistance properties increases the life expectancy of the surface.
• Paintability – easily paintable after 5-6 hours of application.
• Non-toxic – it is non-toxic hence user friendly.

• Surface must be free from dust, oil, grease, and loose particles, etc. moisten the surface before applying Dr. fixit Crack-X Shrinkfree.
• fine hairline cracks must be widened upto 1 mm minimum and then filled.
• for filling Dr. fixit Crack-X Shrinkfree on the internal surfaces, existing POP or painter’s putty must be removed till plaster surface is exposed.

• Press Dr. fixit Crack-X Shrinkfree firmly into the crack One time OnlY with a spatula or putty knife and level the surface.
• handball application can also be used as per the convenience.
• Care must be taken to avoid formation of cavities or bubbles during application.
• allow it to dry in ambient conditions for 5-6 hrs before painting. for best results 7 days air curing is advised.
• further POP or painters putty application can be taken up once it is fully dry

• not for cracks in POP or painter’s putty.
• not recommended to use under the rain.
• not meant for structural cracks in concrete, slab, construction joints.
• Jet or Power washing on walls not advisable prior to application.
• During application below 10°C, drying time will be delayed.
• Container to be tightly closed after application.
• if filler compound becomes too dry, add potable water in ratio of 1 teaspoon in 250 ml of Dr. fixit Crack-X Shrinkfree.

• Consistency - Paste form, without sagging.
• Ease of application – Easy to apply by putty knife similar to conventional putties.
• Flexibility - Flexible, therefore does not crack & accommodates minor movements in cracks.
• VOC - Water based with very low voc hence eco-friendly.
• Application advantage - Can be applied on damp surfaces but not on cracks with running water.
• Paint ability - Over coatable by any type of polymer based paints, after 24 hours.
• Staining - Non-staining.
• Bonding - Excellent adhesion with cementitious surface.
• Durability – Excellent resistance to UV & atmospheric conditions.
• Tinting ability - It can be tinted using water-based stainers.
• Toxicity - Non toxic & harmless to hands.

• Surface must be free from dust, oil, grease, and loose particles etc. Moisten the surface before applying Dr. Fixit Crack-X Paste.
• Fine hair line cracks must be widened up to 1 mm minimum by using scrapper and then filled
• For filling Dr. Fixit Crack-X Paste on the internal surface, existing POP or painter’s putty must be removed till plaster surface is exposed.
• For porous surfaces, apply primer coat prepared with Dr. Fixit Crack-X Paste and water in 1:1 proportion over the crack. Fill Dr. Fixit Crack-X Paste when the surface is tacky and not dried completely.  

• Press Dr. Fixit Crack-X Paste firmly into the crack with a spatula or putty knifes and level with the surface.
• Care must be taken to avoid formation of cavities or bubbles during application.
• Allow it set for 24 hours and then apply another coat of Dr. Fixit Crack-X Paste.
• Further POP or painter’s putty application can be taken up once it is fully dry.
• For best results allow Dr. Fixit Crack-X Paste to cure for 7 days.

• Should not be used for cracks more than 5 mm thick.
• Not for application in cracks in structural members, expansion joints & separation gaps.
• Not for cracks in POP or painter’s putty.
• For application below 10oC, drying time will be delayed.
• Container to be tightly closed after application.

• 25-30 running meter/kg (for a depth of 5mm and width of 5 mm).

A. What is BOSSIL MS POLYMER SEALANT

Description: An elastomeric hybrid sealant based on advanced MS Polymer technology. It is a low-modulus sealant with high movement capability and excellent weathering characteristic.

Applications: Sealing concrete joints (precast wall panels, expansion joints, control joints, FRC boards, etc.), façade cladding (metal panels, natural stones, etc.), window frame perimeter, etc. Other applications sealing anodized aluminum, masonry, porcelain, coated metal, finished wood, epoxy and polyester panels, UPVC, polystyrene, and stainless steel.

Colors: White, Grey & Black

B. Why Kwick Fix Solutions is Best Option for BOSSIL MS POLYMER SEALANT

1. KWICK FIX SOLUTIONS purchases material from the core company / factory or its authorised channel only. Hence, KWICK FIX SOLUTIONS sells only orginal & genuine products.

2. KWICK FIX SOLUTIONS has ready stock and fresh material available.

3. KWICK FIX SOLUTIONS is located in the hub of mumbai transport area. Hence, deliveries are prompt. 

4. KWICK FIX SOLUTIONS is a trusted brand and has a reputation of over 120 years in the market. The company is an extension of a 120 year old firm.

Additional Information:

• Delivery Time: 3 WORKING DAYS