Kwick Fix Solutions

Additional Information:

• Delivery Time: 3 WORKING DAYS

• Roof slabs – flat or sloping, chajjas, folded plate roofs, vaulted roofs, domes etc.
• Flooring, external walls.
• Sunk portion of bathrooms, toilets, balconies, etc.
• Overhead or underground water tanks and other large reservoirs.
• Mortars for filling joints of C.I. or any other drainage pipes.
• As an admixture for providing waterproof plaster to external walls especially in high rise buildings.
• As waterproof additive to any cementbased paints used as a finishing coat.

• Can be easily mixed with cement forming an impermeable co-matrix film.
• High flexural strength and extraordinary adhesion of polymer reinforces the high compressive strength property of cementitious matrix.
• Alkaline and compatible with concrete.
• Does not facilitate carbonation.
• Can be applied in moist conditions e.g: exteriors, terraces and chajjas in wet spells of monsoon, underground and/ or overhead water tanks almost immediately after emptying.
• Moisten the surface with water jet 24 hours prior to the application of POLYALK WP.
• Mix 1 part of POLYALK WP and 1.25 parts fresh white or grey cement by weight using a low-speed stirrer, to form a slurry.
• Continuous hand-mixing to a lump-free consistency may also be adequate.
• Keep the mix continuously stirred.
• Apply the slurry by brush to the damp surface.
• Apply two more coats of similar slurry at 24 hrs intervals.
• Allow to set for 48 hours.
• Cure the coating for 7 days by sprinkling water three times a day on the vertical surface (external walls) and using moist gunny bags on the horizontal surface (terraces).
• For best results, it is necessary to sandwich the cured coating of POLYALK WP with a screed layer.
• Can be mixed with any cement based paint and can thus have any desired colour shade.
• Can be used as a base waterproofing coat. After curing, it can receive Sunext–8 

• Preparation of the surface to be waterproofed is very important.
• Repair and make good any faulty concrete in the form of cracks, honey combing etc mortar.
• Cure the repaired cracks as per the usual norms.
• Remove all curing compounds and sealers.
• Scrub and clean the surface.
• Remove laitance, dirt, paint, loose flakes or particles or other foreign matter etc. using a vacuum cleaner or high pressure water jet or wet sandblasting or wirenbrushing.
• Ensure that the concrete surface possesses an open surface texture.
• Fill hairline cracks with POLYFILL AR, large cracks with POLYALK EP

KWICKSEAL BT 150 is cold- applied, flexible, synthetic rubber sealing tape made from

Preminum Butyl rubber.

It is a two layered 1.5mm Butyl rubber waterproofing layer with an aluminun foil

to protect the material from impacts of UV radiation & to products the adhesion of sealed

elements.

The Bottom Side KWICKSEAL BT is covered with an easily removable protective film.

KWICKSEAL BT is a convenient way to seal various cracks & joints.

It can also be used to insulate junctions for roofing repairs & HVAC.

KWICKSEAL BT is specially designed for sealing substrates like matels, concrete, wood,

Glass, plastic ( TPO, PP,PE ).

• Waterproofing- Additive with cement for waterproofing of roofs, walls & water storage tanks.
• Concrete repair- Additive for cement mortar for repair to spalled concrete, floor, columns, beams, chajja, slab etc.
• Bond coat- Bond coat for old to new concrete & masonry plaster.
• Priming- reinforcement steel.

KWICKSEAL AT 50 is cold- applied, flexible, rubberized Bitumen based sealing tape.

It is a two layered 1.5mm Polymer Bitumen waterproofing layer with an aluminun foil

to protect the material from impacts of UV radiation & to products the adhesion of sealed

elements.

The Bottom Side KWICKSEAL AT is covered with an easily removable protective film.

KWICKSEAL AT is a convenient way to seal various cracks & joints.

It can also be used to insulate junctions for roofing repairs.

KWICKSEAL AT is specially designed for sealing substrates like matels, concrete, wood,