M.K. Petro Products India Private Limited

Usage/Application	Waterproofing
Thickness	2 mm
Brand	MAKPHALT
Packaging Type	ROLL
Physical State	SOLID
Elongation	>60%
Material	Polyester,Aluminium
Country of Origin	Made in India
Length	10-15 m

MAKPOLYPLAST SUPERLAY AL is a Aluminium Foil Topped APP polymeric waterproofing membrane consisting of five layers. The Centre core consists of 160 gsm Non Woven Polyester Mat. The Polyester Mat Film is the reinforcement barrier against water and moisture. The Centre Core is provided on both sides with SBS/APP polymer modified bitumen with properties of high Softening point, Heat resistance and high Penetration making it ideal for waterproofing purposes. The polymer-modified bitumen is protected on both sides with Thermo fusible High Molecular High Density Polyethylene Film. The polymeric membrane has elongation exceeding 40% to absorb all Structural movements. It has a very high tensile strength and cold resistivity to adapt to all contours.

Features:

1) UV Resistant
2) Increase flexibility at low temperature
3) Excellent weathering
4) Fire resistant

Areas of Application:

1) Airport aprons & Ramp areas
2) Bridges & Tunnels
3) Inverted roofs & Parapets
4) Terrace, Balconies & Patios
5) Concrete Foundation & Footings
6) Basement & Pile Heads
7) Swimming Pools
8) Water retaining bodies and tanks. 

Application Procedure:

1. The Surface has to be cleaned to have a smooth Surface.
2. Apply a coat of MAK PRIMER @ 0.3 L /sqm 3. MAK POLY PLAST SUPERLAY is unrolled over the coated surface and bonded completely on the substrate. The overlaps are sealed with L.P.G Torch with end overlaps 100 mm and side overlaps 75 mm 4. Laying 120 gsm geotextile as separation layer for covering application.
5. MAK POLYPLAST SUPERLAY is topped with Cement Screed or tiles for covering application otherwise for exposed areas MAK SILVER (Bituminous paint) is to be laid over the membrane.

Additional Information:

• Production Capacity: as per requirement
• Delivery Time: within a week

Usage/Application	Applied with hot bitumen
Packaging Size	1X20 Mtr
Color	Black
Material	HMHDPE
Brand	Makphalt
Raw Material	20 Micron HMHDPE center core
Thickness	1.0 mm or 1.5 mm
Packaging Type	1x20 Meter Roll
Country of Origin	Made in India
Length	20 and 90 m

Mak Membrane HDPE -P is a unique membrane HDPE film pressure sensitive adhesive which allows poured concrete to bond fully with the membrane. It provides water, water vapour and gas protection to water excluding structures and protects concrete from aggressive ground salts, chemicals and hydrocarbons. Mak Membrane HDPEP is supplied with a self- adhesive selvedge along one side of the roll to provide sealed laps and a comprehensive range of auxiliary products to simplify the application process.

Application and Advantages: 

• Basement waterproofing protection to grades 1,2 and 3 as defined in BS8102:2009.

• To provide a vapour and waterproof membrane in building and civil engineering structures.

• Resistant to attack from chemicals and aggressive ground salts.

• Forms a unique, integral bond to poured concrete by pressure sensitive adhesive and remaining in place if settlement of the substrate occurs.

• Simple application - no primers or protection material required.

• Inert product - no risk of a reaction with ponded waste prior to concrete being poured.

• Protects concrete from attack of chemicals, hydrocarbons and aggressive ground salts in contaminated sites.

• Facilitates flexible construction programming.

• Full range of Makphalt hydrophilic and PVC waterstops available to provide complete solution to waterproofing of the structure.

Specification Clauses: 
The waterproof tanking membrane shall be Mak Membrane HDPE-P, consisting of HDPE membrane which bonds integrally to freshly poured concrete by pressure sensitive adhesive bond.

The membrane shall be supplied with one self-adhesive selvedge to provide sealed laps and comply with British Standard 8102 2009 - Code of practice for “Protection of Structures Against Water from the Ground” to provide basement waterproofing protection to grades 1, 2 and 3.

Application Procedure:  

Surface preparation 

Horizontal application - the membrane must be applied to smooth, prepared substrate. Concrete blinding is preferred. The substrate shall be free from loose aggregate or other sharp protrusions.

Standing water must be removed to prevent contamination of overlaps and subsequent compromise of waterproof properties.

Vertical application - the membrane is applied to temporary or permanent formwork or adjoining structures. Mak Membrane HDPE-P must not be applied directly onto contiguous or secant piled walls. A plywood sacrificial shutter or spray concrete finish should be used prior to application.

Membrane installation

Cut the membrane to a convenient length for installation. Carefully align the membrane and roll it out with printed coated side facing the concrete pour. Lay adjacent sheets accurately so they overlap the previous sheet 75mm along the adhesive selvedge. When laying adjacent full rolls there should be a stagger of half a roll length to avoid building up of end joints in one area.

All overlaps and joints should be firmly rolled to ensure complete adhesion between layers. Remove all release tapes with a short sharp pulling action, especially in hot weather

Removal of formwork
Where the membrane has been applied to removable shuttering it is recommended that a minimum concrete compressive strength of 10 N/mm² is reached before the formwork is stripped.

Penetrations 
Penetrations e.g., pipe entries through Mak Membrane HDPE-P, require special attention to detail. Refer to M.K. Petro Products India Pvt Ltd for more information on details.

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: Within a week

Brand	M.K. Petro
Usage/application	Commercial
Color	Black
Features	Water Proof
Material	Bitumen
Surface Treatment	Film Coated
Manufacturing Technique	Cold Rolled
Country of Origin	Made in India

We are offering Plastic Bitumen Felts. 

These are APP modified membranes reinforced with plastic films and are ideal for all types of waterproofing in single or multiple layers.

Thickness available: 1mm, 1.5mm, 2mm, 3mm

Bituminous plastic felts are very cost effective and last decades.

Brand	MAK PHALT
Packaging Size	20 Kg
Color	Black
Usage/Application	concrete and brick foundations, retaining walls and bridge abutments
Application Method	Brush
Coverage	approx. 1.5 - 2 sqmt./Kg / 2 Coats
Coats Required	min. 2 coat
Recoating	Minimum 6 hours gap should be given between coats for drying

INSTA FLEX BLACKFLEXIBLE BITUMEN MODIFIED COATING
Category: Retail RangeINSTA FLEX BLACK is high performance water proofer that dries to form a tough impermeable coating. It is a blend of tropical grade bitumen emulsion with 8% added pure acrylic polymer.
Excellent crack bridging capacity. Highly flexible.Excellent bonding to substrate such as concrete, masonry, wood, metal, plastic, etc.Very good bonding to damp surfaces.Provides a key to plaster on difficult surfaces.Easy to use.Packing: INSTA FLEX BLACK is available in 1, 4, 20 and 50 Kg packs.
Coverage: INSTA FLEX BLACK will cover approx. 1.5 – 2 sqmt./Kg / 2 Coats, depending upon the porosity of the surface.
PRIMARY APPLICATIONSAs an impervious waterproofing membraneUseful on concrete and brick foundations, retaining walls and bridge abutments.For protection of Interior and exterior walls.Can be used as adhesive to bond wood blocks, expanded polystyrene and cork tiles to any surface.Could be used as a primer/ bond coat on bituminous substrates.
DIRECTIONS FOR USEThe surface to be coated should be free from all loose particles, dust, oil and laitance. All visible cracks should be opened in ‘V’ grove and filled with CRACK FILL, a single component crack filling compound.
INSTA FLEX BLACK is applied in min. 2 coat application. 10-15% dilution with water is recommended to make the material brushable. Minimum 6 hours gap should be given between coats for drying.