Pidilite Industries Limited

Viscosity at 200degreeC	75,000+- 10,000 mPas
Density at 20 degreeC	1.52 +- 0.03 g/cm3
Processing temperature	180-200 degreeC
Feed speed	16 - 60 m/min
Softening range	approx. 90 +- 5 degreeC
Heat resistance	approx. 80 +- 5 degreeC
Open time at 190 degreeC	approx. 8 +- 1 s

Edgebanding:
For bonding thermoplastic edgebands (e.g. ABS, PP, PVC), edgebands made of resinated decor paper, veneer (with or without fleece backing), or solid wood edges.The properties of the bonded parts and, where necessary, the reverse primer coating of the edgebanding materials have to undergo application-related testing prior to use.

Directions for Use:
The adhesive granulate can be processed using automatic feed systems. In that case, the ambient temperature should not exceed 30 °C.Different types of hot melt adhesives may be incompatible with each other depending on the formulation. Therefore, we recommend to carefully clean the application equipment when changing the product. Further information is available upon request.The processing characteristics may vary depending on the application technology used as well as at differing feed speeds, which can affect the bonding process.

Cleaning:
Preliminary mechanical cleaning while hot (e.g. with a suitable spatula which does not damage the unit). Remove any residues in the application environment when cold using Jowat® Cleaner 402.40.

Safety Considerations:
Like all hot liquids, this product can cause severe burns in the molten state. Please take appropriate precautions to prevent the hot adhesive from coming into contact with the skin (e.g. by wearing appropriate protective gloves). If this does happen, cool the affected area immediately with water. Do not try to remove the adhesive from the skin. Seek medical attention.
Hot melt adhesives with hazard-free labeling may release vapors when processed. It is recommended not to exceed the indicated processing temperature, to keep the formation of vapors as low as possible. Extraction and ventilation are recommended especially if an open application system is used. 

Storage:
The product should remain stored in closed original containers, dry and cool.For best-before date, please see container label.After the elapse of the best-before date, it is essential that you again verify that the product is fit for your intended application.

Packaging:
Information about packaging types and units is available upon request.

Remarks:
For further information concerning safety, handling, transport and disposal, please refer to the safety data sheet.The information on this data sheet is based on test results from our laboratories as well as on reported experience gained in the field by our customers. It can, however, not cover all parameters for each specific application and is therefore not binding upon Jowat, nor should it be relied upon in lieu of your own required testing. The information given in this leaflet does not represent a performance guarantee. Unless otherwise agreed with our customers, the values stated in the section “Specification” shall be regarded as the finally agreed upon product properties. No liability may be derived from the information contained herein nor from the information provided by our free technical advisory service.

Density	pprox.1.3 g/ml
Softening Point	approx.115 DegreeC(238 DegreeF) Ring&Ball
Viscosity	approx.180,000at190 degreeC
Basis	Ethylene-Vinyl Acetate(EVA)
Color	50-natural; 51-white; 52-brown; 53-black

Characteristics:
High viscosity hot melt with high heat resistance and good cold flexibility of glue line.Excellentcolor and heat stability in the melt.

Applications:
Hot melt for automatic edgebanding suitable for solid wood,veneer,PVC and resinated paperedgebands.Also used for softforming applications.

Cleaning:
Preliminary cleaning while hot by scraping with a spatula.

Storage:
May be stored for12months after date of shipment from Jowat,in properly closed original containers,cool and dry(15-25°C).

Packaging:
In plastic bags of55lbs.net.

Marking:
None.We recommend drawing off any vapors which may form.Consult Material Safety DataSheet.

Viscosity at 200 degreeC	90,750 +- 19,500 mPas
Density at 20 degreeC	1.33 +- 0.04 g/cm3
Processing temperature	180 - 200 degreeC
Feed speed	10 - 60 m/min
Softening range	approx. 90 +- 5 degreeC
Heat resistance	approx. 90 +- 5 degreeC
Open time at 190 degreeC	approx. 8 +- 2 s

Edgebanding:
For bonding thermoplastic edgebands (e.g. ABS, PP, PVC), edgebands made of resinated decor paper, veneer (with or without fleece backing), or solid wood edges.The properties of the bonded parts and, where necessary, the reverse primer coating of the edgebanding materials have to undergo application-related testing prior to use.

Directions for Use:
The adhesive granulate can be processed using automatic feed systems. In that case, the ambient temperature should not exceed 30 °C.Different types of hot melt adhesives may be incompatible with each other depending on the formulation. Therefore, we recommend to carefully clean the application equipment when changing the product. Further information is available upon request.The processing characteristics may vary depending on the application technology used as well as at differing feed speeds, which can affect the bonding process.

Cleaning:
Preliminary mechanical cleaning while hot (e.g. with a suitable spatula which does not damage the unit). Remove any residues in the application environment when cold using Jowat® Cleaner 402.40.

Safety Considerations:
Like all hot liquids, this product can cause severe burns in the molten state. Please take appropriate precautions to prevent the hot adhesive from coming into contact with the skin (e.g. by wearing appropriate protective gloves). If this does happen, cool the affected area immediately with water. Do not try to remove the adhesive from the skin. Seek medical attention.
Hot melt adhesives with hazard-free labeling may release vapors when processed. It is recommended not to exceed the indicated processing temperature, to keep the formation of vapors as low as possible. Extraction and ventilation are recommended especially if an open application system is used. 

Storage:
The product should remain stored in closed original containers, dry and cool.For best-before date, please see container label.After the elapse of the best-before date, it is essential that you again verify that the product is fit for your intended application.

Packaging:
Information about packaging types and units is available upon request.

Remarks:
For further information concerning safety, handling, transport and disposal, please refer to the safety data sheet.The information on this data sheet is based on test results from our laboratories as well as on reported experience gained in the field by our customers. It can, however, not cover all parameters for each specific application and is therefore not binding upon Jowat, nor should it be relied upon in lieu of your own required testing. The information given in this leaflet does not represent a performance guarantee. Unless otherwise agreed with our customers, the values stated in the section “Specification” shall be regarded as the finally agreed upon product properties. No liability may be derived from the information contained herein nor from the information provided by our free technical advisory service.

Processing temperature	100 - 120 degC
Density at 20 DegreeC	approx. 1.10 +- 0.10 g/cm3
Softening range	approx. 65 +- 5 degC
Open time at 120 degC	approx. 7 +- 3 s
Reaction time	approx. 4 - 7 d

Application:For bonding thermoplastic edgebands (e.g. PVC, ABS, PP, PMMA) with a suitable primer coating on the reverse side, as well as edgebands made from resinated decor paper, aluminium with an appropriate pretreatment, or veneer.Characteristics/ Directionsfor Use:Fast setting, high initial strength.** Compared to other Jowat products for this application.Processing with special equipment from moisture-proof sealed containers. Upon advice of the machine manufacturer, not to be used on HOLZ-HER edgebanders with a Glu Jet system. The viscosity of the product may increase during storage due to the ingredients’ chemical reactions that cannot be influenced. High storage temperatures promote that increase in viscosity.

Processing temperature	180-200 degreeC
Feed speed	10 - 75 m/min
Softening range	approx. 95 +- 5
Heat resistance	approx. 90 +- 5
Open time at 190 DegreeC	approx. 12 +- 2 s

Edgebanding:
For bonding thermoplastic edgebands (e.g. ABS, PP, PVC), edgebands made of resinated decor paper, veneer (with or without fleece backing), or solid wood edges.The properties of the bonded parts and, where necessary, the reverse primer coating of the edgebanding materials have to undergo application-related testing prior to use.

Directions for Use:
The adhesive granulate can be processed using automatic feed systems. In that case, the ambient temperature should not exceed 30 °C.Different types of hot melt adhesives may be incompatible with each other depending on the formulation. Therefore, we recommend to carefully clean the application equipment when changing the product. Further information is available upon request.The processing characteristics may vary depending on the application technology used as well as at differing feed speeds, which can affect the bonding process.

Cleaning:
Preliminary mechanical cleaning while hot (e.g. with a suitable spatula which does not damage the unit). Remove any residues in the application environment when cold using Jowat® Cleaner 402.40.

Safety Considerations:
Like all hot liquids, this product can cause severe burns in the molten state. Please take appropriate precautions to prevent the hot adhesive from coming into contact with the skin (e.g. by wearing appropriate protective gloves). If this does happen, cool the affected area immediately with water. Do not try to remove the adhesive from the skin. Seek medical attention.
Hot melt adhesives with hazard-free labeling may release vapors when processed. It is recommended not to exceed the indicated processing temperature, to keep the formation of vapors as low as possible. Extraction and ventilation are recommended especially if an open application system is used. 

Storage:
The product should remain stored in closed original containers, dry and cool.For best-before date, please see container label.After the elapse of the best-before date, it is essential that you again verify that the product is fit for your intended application.

Packaging:
Information about packaging types and units is available upon request.

Remarks:
For further information concerning safety, handling, transport and disposal, please refer to the safety data sheet.The information on this data sheet is based on test results from our laboratories as well as on reported experience gained in the field by our customers. It can, however, not cover all parameters for each specific application and is therefore not binding upon Jowat, nor should it be relied upon in lieu of your own required testing. The information given in this leaflet does not represent a performance guarantee. Unless otherwise agreed with our customers, the values stated in the section “Specification” shall be regarded as the finally agreed upon product properties. No liability may be derived from the information contained herein nor from the information provided by our free technical advisory service.