X

Poonam Paints Corporation

Kashewadi, Pune, Maharashtra

| GST  27AABFP4636J1Z3

| Verified Supplier

View Mobile Number 80% Response Rate
Hi
I agree to the terms and privacy policy
Verifying...
1

Have a requirement?
Get Best Price

Urethane Coatings

We are a leading Distributor of Urethane Coatings such as Berger Epoxy PU Coating Finish, Bergerthane PU Finish, Bergerthane Finish and Bergerthane PU Matte Finish from India.

Berger Epoxy PU Coating Finish
Interested in this product?
Get Best Quote
Backed by qualified professionals, we are providing a comprehensive range of Berger Epoxy PU Coating Finish.

Uses:


  • An ideal high build coating for application on structural, pipelines, tank ages and other critical areas of fertilizers, petrochemicals, heavy chemicals, metallurgical industries, etc the product has tendency to chalk on exposure which will not impair with performance.

 

Scope:

  • A high build polyurethane coating to provide excellent corrosion resistance properties in chemical and saline environments. When fully cured it forms a tough, abrasion resistant finish. It is also suitable as a tank coating for storage of a wide range of commodities.

Product Data:

  • Type : Two Pack, cured with Aromatic isocyanate
  • Composition : Epoxy resin with urethane hardener, suitably pigmented
  • Mixing Ratio : Base : Catalyst - 3 : 1 by volume
  • Pot Life : 4-6 hours
  • Application : Brush or Airless Spray
  • Recommended DFT : 55-65 microns per coat
  • Corresponding WFT : 110-130 microns per coat
  • Theoretical Spreading Rate :7.7-9.1 Sq. MtrjLtr.
  • Drying Time : TOUCH : 90 minutes HANDLE : 6-8 hours HARD : Overnight
  • Curing Time : 7 days
  • Overcoating Interval : MIN : Overnight MAX : 5 days
  • Flash Point : Above 22° C
  • Colour : Assorted shades
  • Finish : Egg shell
  • Packing : 20 Ltrs.
  • Thinner/Cleaner : Thinner 841 IGF
  • Storage Life : Up to twelve months as long as the sealed containers are kept under cover in a dry place under normal temperature conditions.


Surface Preparation:

  • Steel : remove grease, oil and other contaminants preferably by using bison degreasing solvent. Blast clean to a minimum 21/2 Swedish standard sis 05 5900 with a surface profile not exceeding 35-40 microns. If blasting is not practical, make full use of mechanical tools along with manual chipping and wire brushing to remove loose rust and scale to st. 2 Swedish standard sis 05 5900. Excessive burnishing of steel is to be avoided. Thoroughly dust down all surfaces. Best results can be achieved if the manually cleaned surface is primed with protectorate - self priming surface tolerant coating. The surface should be clean and dry before application of appropriate primer coat. New
  • Concrete : ensure that the concrete is cured for a minimum of three months. The surface is to be made rough and free from emittance and other contaminants by sand sweeping. Old concrete : remove all salt deposits from the surface by water jet washing. Light sand blast the surface to remove all loosely bound coatings and roughening up of cornily adhering coatings to ensure anchorage with recommended systems. Ensure all dust/other particles are fully removed by suction or air blast and the surface is fully cleaned and dry before application of paints. In non-critical areas where blasting is not possible, water jet washing and hard wire brushing are minimum requisites.

Application:

  • Stir the base thoroughly and then mix three parts of base and one part of catalyst by volume to uniform consistency. Allow the mixture to mature for 30 minutes and stir again before use and during application.
  • Brush : Apply preferably without any thinning. However, add up to 5% Thinner 841 IGF If required, depending on conditions.
  • Airless Spray : Apply preferably without any thinning. However, up to 5% Thinner 841 IGF may be added if absolutely essential, depending on conditions.
  • Use any standard equipment having pump ratio 40 : 1. Tip size 0.48-0.66 mm. Tip pressure 110-160 Kg/cm2.

View Complete Details

Yes, I am interested!

Bergerthane PU Finish
Interested in this product?
Get Best Quote

Bergerthane PU Finish

Get Latest Price

We are involved in providing an extensive series of Bergerthane  PU Finish that is processed by capable professionals who use the advanced techniques. 

Uses:


  • Ideal for application on tank ages (exterior), structural steel, equipment of any industry under highly corrosive environment.
  • The product is suitable for application over suitable epoxy or zinc borne primer or intermediates.

 

    Scope:

    • A high performance urethane semi-glossy coating suitable for corrosion protection in chemical environments.
    • build finish provides excellent durability and aesthetic retention for structural exposed to marine, highly humid and chemical conditions.


    Product Data:

    • Type: Two Pack, cured with Aliphatic Isocyanate.
    • Composition: Acrylic resin with urethane hardener suitably pigmented
    • Mixing Ratio : Base: Catalyst 10:1 by volume
    • Pot Life: 2-4 hours depending on conditions.
    • Application: Brush and spray. Airless spray suggested for uniform and high film build. Recommended DFT: 75-125 microns per coat.. Corresponding WFT: 108-179 microns per coat. Theoretical Spreading Rate : 5.2 — 8.6 Sq. Mtr. / Ltr. Drying Time : Touch : Within 1 hour 30 minutes. Handle : 12 — 14 hours Hard : 24 Hours. Curing: 7 days.
    • Over coating Interval : Min: 24 hours
    • Max: 5 days.
    • Flash Point : Above 22°C
    • Colour: Assorted shades.
    • Finish : Glossy Packing : 11Itrs.
    • Thinner I Cleaner : Thinner 825
    • Storage Life : Up to twelve months as long as the sealed containers are kept under cover in a dry place under normal temperature conditions.


    Additional Information:

    • Item Code: 41-SG

    View Complete Details

    Yes, I am interested!

    Bergerthane Finish Urethane Coatings
    Interested in this product?
    Get Best Quote
    Being a well-known firm, we are engaged in providing Bergerthane Finish  to fulfill the needs of our customers. 

    Use:


    • Recommended for use in new construction and maintenance services over properly primed surfaces. An effective top coat for use in refineries, petrochemicals, fertilizers, chemicals, infrastructure and other industrial installations.

    Scope:

    • An acrylic polyurethane enamel which provides a durable high gloss exterior and interior coating for chemical and saline coastal environments. It has excellent colour and gloss retention properties. When fully cured, it forms an extremely tough and abrasion resistance finish. A non-pigmented version is available as Bergerthane Clear.


    Product Data:

    • Type : 1Wo Pack. cured with Aliphatic Isocyanate
    • Composition : Acrylic resin with urethane hardener suitably pigmented
    • Mixing Ratio : Base : Catalyst -4 : 1 by volume
    • Pot Life : 8-8 hours
    • Application : Brush. Conventional or Airless Spray
    • Recommended DFT : 30-35 microns per coat
    • Corresponding WFT : 75-88 microns per coat
    • Theoretical Spreading Rate : 11.4-13.3 Sq. Mtr./Ltr.
    • Drying Time : TOUCH : 1 hour HANDLE : 4-6 hours HARD : Overnight
    • Curing Time : 7 days
    • Overcoating Interval : MIN : Overnight MAX : 5 days
    • Flash Point : Above 22° C
    • Colour : Assorted shades
    • Finish : Glossy
    • Packing : 20 Ltrs.
    • Thinner/Cleaner : Thinner 825
    • Storage Life : Up to nine months as long as the sealed containers are kept under cover in a dry place under normal temperature conditions.

    View Complete Details

    Yes, I am interested!

    Bergerthane PU Matte Finish
    Interested in this product?
    Get Best Quote
    With the years of practice, we are betrothed in providing a broad range of Bergerthane PU Matte Finish that meets on client’s demand. 

    Uses:

    • Recommended for use in new construction and maintenance services as an effective top coat. This is suitable,for use In refineries, petrochemical, fertilizer, chemical, transportation industries, power plants etc.

    Scope:

    • A polyester polyurethane coating to provide a durable matt finish for industrial environments. It has excellent colour and gloss retention properties. When fully clued, it forms an extremely tough and abrasion resistant finish. The product Is compatible with epoxy and PU undercoats.

    View Complete Details

    Yes, I am interested!
    Tell us what you
    need
    Receive seller
    details
    Seal the deal
    Pay with IndiaMART
    Save time! Get Best Deal
    I agree to the terms and privacy policy