30 Feet Heavy Duty Roll Turing Lathe Machine, 105 mm
Bed Length | 30 Feet |
Height of Centre | 800 mm |
Swing Over Bed | 1600 mm |
Spindle Bore | 105 mm |
Applicable Industry | Power Plant, Shipbuilding, Oil Industry, Forging Plant |
Functions:
HEAD STOCK: Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.
BED:It is the base of the lathe machine. It is made of the single-piece casting of Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.
TAILSTOCK:Tail Stock is situated on the right side above the lathe bed.
It is used for:
- Support the long end of the job for holding and minimizes its sagging.
- It holds the tool for performing different operations like drilling, reaming, tapping, etc.
* And it is also used for a small amount of taper for a long job by offsetting the tailstock.
CARRIAGE:* The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
* It gives rigid supports to the tool during operations.
* It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.
SADDLE:Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.
CROSS SLIDE:It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot
COUMPOUND REST:It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.
TOOL POST:It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.
APRON:An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.
LEAD SCREW:A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.
FEED ROD:Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side
CHUCK:Chuck is used to holding the work piece securely.
Features:* Rigid section straight wide bed with hardened and ground guide ways
* Main spindle supported on precision ball bearings.
* Pre-loaded Leading screws and nuts for Turning and Threading.
* Rear tool post with tool holder.
* Hardened Ground Head stock spindle and Tail sock sleeve
* Bed ways- 3 v & 1 flat
Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.
Product Details
Company Details
Product Specification
Bed Length | 30 Feet |
Height of Centre | 800 mm |
Swing Over Bed | 1600 mm |
Spindle Bore | 105 mm |
Applicable Industry | Power Plant, Shipbuilding, Oil Industry, Forging Plant |
Bed Width | 850 mm |
Number of Spindle Speeds | 6 |
Distance Between Centre | 7000 mm |
Swing Over Cross Slide | 1400 mm |
Maximum Swing in Gap | 1900 mm |
Lead Screw Diameter | 75 mm |
Motor Power | 15 HP |
Machine Weight | 13000 kg |
Product Description
Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.
Functions:
HEAD STOCK:
Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.
BED:
It is the base of the lathe machine. It is made of the single-piece casting of Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V' formed upon them and rigidly supported with cross girths.
TAILSTOCK:
Tail Stock is situated on the right side above the lathe bed.
It is used for:
- Support the long end of the job for holding and minimizes its sagging.
- It holds the tool for performing different operations like drilling, reaming, tapping, etc.
- And it is also used for a small amount of taper for a long job by offsetting the tailstock.
CARRIAGE:
- The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
- It gives rigid supports to the tool during operations.
- It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.
SADDLE:
Generally, it is made up of ‘H' shaped casting and it has a ‘V' guide and a flat guide for mounting it on the lathe bed guide ways.
CROSS SLIDE:
It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot
COUMPOUND REST:
It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.
TOOL POST:
It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.
APRON:
An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.
LEAD SCREW:
A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.
FEED ROD:
Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side
CHUCK:
Chuck is used to holding the work piece securely.
Features:
- Rigid section straight wide bed with hardened and ground guide ways
- Main spindle supported on precision ball bearings.
- Pre-loaded Leading screws and nuts for Turning and Threading.
- Rear tool post with tool holder.
- Hardened Ground Head stock spindle and Tail sock sleeve
- Bed ways- 3 v & 1 flat
Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.
Product Video
About the Company
The quality of our range is persistently maintained & upgraded as per the developing technical scenarios. It is due to this high quality range that we are successfully venturing in our business and exporting our range to global regions such as Gulf nations, Africa, South East Asian Countries, Bhutan and many other nations. Moreover to facilitate our clients we also modulate our range in accordance to the specifications given by our cherished clients.
Company Video
Seller Contact Details
No. 127, Focal Point, Batala, Focal Point Batala - 143505, Gurdaspur, Punjab, India
Get Directions