This is an average seller rating received from buyers based on-
Communication: Quick reply to buyer's enquiry and follow ups
Conduct: Politeness while dealing with buyer
Quality: Good quality products and services as per commitment
Experience: Timely delivery, after sales service and resolution to queries
View Mobile Number 84% Response Rate
Call +91-804883755684% Response Rate
Ask for more details from the seller
Less Than 150 Degree C
L-300 N,T-250 N
No Crack (Up to -2 Degree C)
Elongation at Break
L - 40%,T-40%
No flow (120 Degree C)
LAP Joint Strength
L -700,T- 450 (N/5CM)
Resistance to Water Pressure
No leakage (5 bar/50M)
10 M X 1 M X 3.0 mm,10 M X 1 M X 4.0 mm
3 mm / 4 mm
Dr. Fixit Torchshield AM are polyester reinforced, APP modified bitumen membranes, top surface is covered by a uniform layer of natural or coloured slate chippings and the underside is finished with a polyethylene film, has a lateral selvedge for overlapping is designed as a single layer for the installation of new or refurbished flat roofs (metal or prefabricated structures, walkable or non walkable terraces, domes or shed roofs) while also ensuring exceptional, proven performance.
Areas of Application:
Dr. Fixit Torchshield AM membranes are intended for use as a single layer roof waterproofing system on new or refurbishment works directly to existing substrates. The self-finished mineral surface provides a decorative and solar protective finish for the waterproofing membrane system.
Method of Application: Surface Preparation:
All surfaces to receive Dr. Fixit Torchshield AM must be clean, dry and free from all contaminants that may affect the adhesion and performance of the membrane. Surfaces must be free of sharp projections and mechanical fixings must be well driven to prevent damage to the membrane. All surfaces must be primed with Dr. Fixit Bitushield Primer SB and left to dry completely prior to the application of the waterproofing.
Dr. Fixit Torchshield AM membranes are applied by a torch-on application using a standard roofer’s torch. The membranes should be heated carefully ensuring the PE film on the underside is completely removed as work proceeds and to ensure adequate adhesion to the substrate. All laps should be properly secured in its lap joints, during application ensuring that a continuous 5 mm bead of bitumen is extruded from all laps. Side laps must follow the manufactured mineral free selvage. In any case, side laps should be a minimum of 100 mm, with end laps of a minimum of 150 mm, when not using the granule-free roll end.
Application Tools and Equipment:
The tools and equipment required to apply Dr. Fixit Torchshield AM membrane include a gas torch with a related gas cylinder, a knife for cutting the membrane to size, and a trowel with a rounded tip. Protective gloves and goggles are necessary when using the gas torch.
Precautions & Limitations:
Any naked flame should be kept well away from gas cylinders.
When ignited the Dr. Fixit Torchshield should be watched at all times.
The torch should not be rested on finished roofing.
Extreme care should be taken when working near combustible materials or items which might be scorched by the gas flame.
Not to be applied in extreme cold climatic conditions (below 5˚C).
Not to be applied on damp/wet areas & areas subject to moisture restoration.
Do not overheat the Dr. Fixit Torchshield membrane i.e. avoid heating when it starts smoking.
The moisture content on the surface should not exceed 6% to overlay the membrane.
Use of a bitumen based primer is a must. For better results, use Dr. Fixit Torchshield Primer.
Store rolls upright in the dry area.
Store indoors in a ventilated area.
Keep rolls protected from exposure to heat, sun, cold and moisture.
Do not double stack rolls.
Do not store rolls on their sides.
Use care in the handling of the rolls.
Do not overload the roof. Stagger the rolls across the roof. Avoid excessive weight in a concentrated area.
Interested in this product?Get Latest Price from the seller
About the Company
Year of Establishment2001
Legal Status of FirmLimited Company (Ltd./Pvt.Ltd.)
Nature of BusinessManufacturer
Number of Employees501 to 1000 People
Annual TurnoverRs. 500 - 1000 Crore
IndiaMART Member SinceJan 2012
Import Export Code (IEC)03880*****
Dr. Fixit has been the pioneer in the waterproofing chemical industry by providing adept water proofing solution, high-quality products and services