Legal Status of Firm
Partnership Firm
Year of Establishment
2012
Annual Turnover
Rs. 10 - 25 Crore
Indiamart Member Since
Nov 2013
Electrical Switch Gear Risk Assessment Study And Hazard Analysis
Kind of Application | Industrial Plants |
Service Charges | As per the requirement |
Voltage | LV,MV,HV |
Service location | On Site service |
Service offered | identifying and taking sensible and proportionate measures to control the risks in your workplace |
in an electric power system, switchgear is the combination of electrical disconnect switches, fuses or circuit breakers used to control, protect and isolate electrical equipment. Switchgears are used both to de-energize equipment to allow work to be done and to clear faults downstream. This type of equipment is directly linked to the reliability of the electricity supply one of the basic functions of switchgear is protection, which is interruption of short-circuit and overload fault currents while maintaining service to unaffected circuits. Switchgear also provides isolation of circuits from power supplies. Switchgear is also used to enhance system availability by allowing more than one source to feed a load.switchgear can be classified on the basis of voltage level in to the following
- low voltage (lv) switchgear
- medium voltage (mv) switchgear
* high voltage (hv) switchgear
risk assessment is the determination of quantitative or qualitative estimate of risk related to a well-defined situation and hazard.if you use switchgear you must assess the risks and manage them to ensure safe operation and minimise the risk of injury. A risk assessment is about identifying and taking sensible and proportionate measures to control the risks in your workplace
electrical switchgear hazard categories
the hazards are divided into several main categories, where each category is further subdivided describing specific sources of hazards. The complete list facilitates a thorough check whether all aspects of safety are covered.the main categories are:* hc 1 essential health and safety requirements
* hc 2 design and construction
* hc 3 information requirements
* hc 4 control systems
* hc 5 guards and protective devices
* hc 6 installation, operation and maintenance
inspection of switchgear environment, for example the switchroom or substations, regularly is mandatory. During the inspection you should prioritise any remedial actions as follows:* immediate. This should always be the case when security of the substation enclosure has been interfered with.
* earliest possible opportunity.
* next scheduled maintenance. You should include the following items in the inspection schedule:
* switchgear environment (switchroom access and surrounds, including fence and external walls if outdoors):
in electrical switchgear safety you should look for following factors signs of water getting in/dampness* signs of unauthorised access and/or interference
* condition of firefighting equipment and warning notices
* general housekeeping
* signs of abnormal conditions such as high temperature, smell of hot substances or ozone, presence of smoke, signs of fresh leakage of oil or compound, distortion and evidence of sooting on enclosures
* general condition of switchgear, such as corrosion, evidence of leaks, fluid levels, presence/condition of labels, padlocks and key exchange interlocks, condition of instruments and protection equipment
* condition of ancillary equipment such as batteries and chargers, control panels etc
Product Details
Company Details
Product Specification
Kind of Application | Industrial Plants |
Service Charges | As per the requirement |
Voltage | LV,MV,HV |
Service location | On Site service |
Service offered | identifying and taking sensible and proportionate measures to control the risks in your workplace |
Scope | To assess and manage the switchgear to ensure safe operation and minimize the risk of injury. |
Voltage levels handled | Low voltage (LV) Switchgear,Medium voltage (MV) Switchgear,High voltage (HV) Switchgear |
Product Description
electrical switchgear risk assessment study and hazard analysis service
in an electric power system, switchgear is the combination of electrical disconnect switches, fuses or circuit breakers used to control, protect and isolate electrical equipment. Switchgears are used both to de-energize equipment to allow work to be done and to clear faults downstream. This type of equipment is directly linked to the reliability of the electricity supply
one of the basic functions of switchgear is protection, which is interruption of short-circuit and overload fault currents while maintaining service to unaffected circuits. Switchgear also provides isolation of circuits from power supplies. Switchgear is also used to enhance system availability by allowing more than one source to feed a load.
switchgear can be classified on the basis of voltage level in to the following
- low voltage (lv) switchgear
- medium voltage (mv) switchgear
- high voltage (hv) switchgear
risk assessment is the determination of quantitative or qualitative estimate of risk related to a well-defined situation and hazard.
if you use switchgear you must assess the risks and manage them to ensure safe operation and minimise the risk of injury. A risk assessment is about identifying and taking sensible and proportionate measures to control the risks in your workplace
the hazards are divided into several main categories, where each category is further subdivided describing specific sources of hazards. The complete list facilitates a thorough check whether all aspects of safety are covered.
the main categories are:
- hc 1 essential health and safety requirements
- hc 2 design and construction
- hc 3 information requirements
- hc 4 control systems
- hc 5 guards and protective devices
- hc 6 installation, operation and maintenance
inspection of switchgear environment, for example the switchroom or substations, regularly is mandatory. During the inspection you should prioritise any remedial actions as follows:
- immediate. This should always be the case when security of the substation enclosure has been interfered with.
- earliest possible opportunity.
- next scheduled maintenance. You should include the following items in the inspection schedule:
- switchgear environment (switchroom access and surrounds, including fence and external walls if outdoors):
signs of water getting in/dampness
- signs of unauthorised access and/or interference
- condition of firefighting equipment and warning notices
- general housekeeping
- signs of abnormal conditions such as high temperature, smell of hot substances or ozone, presence of smoke, signs of fresh leakage of oil or compound, distortion and evidence of sooting on enclosures
- general condition of switchgear, such as corrosion, evidence of leaks, fluid levels, presence/condition of labels, padlocks and key exchange interlocks, condition of instruments and protection equipment
- condition of ancillary equipment such as batteries and chargers, control panels etc
About the Company
We, Reliserv Solution from 2012 are one of the leading organizations involved in wholesale distributor, trader and service provider a broad spectrum of Numerical Relay. Offered range includes the finest quality Numerical Relay, VCB Breaker Spares, Electrical AMC Services and many more. All these products are designed by using only optimum grade components at vendors end. Offered products are highly demanded across the market for their unmatched quality, high durability, easy to use, high functionality and super performance. To suit the varied needs of our valued clients, these products are used in various fields.
Company Video
Seller Contact Details
Office No. 9, Plot No. 53/54, Space Heights, Panvel Navi Mumbai - 410209, Thane, Maharashtra, India
Get Directions