IndiaMART > Industrial Furnaces & Ovens > Furnace Burners > Industrial Gas Burner
Fire All Gas Burner

Fire All Gas Burner

Get Latest Price
FIRE ALL GAS BURNER – 1514
These hardy nozzle-mix burners have been used for many years on high temperature furnaces such as those for forging steel, melting aluminum or brass, and reheating steel bars or ingots… and on low temperature ovens and air heaters. Their sealed-in construction allows maximum efficiency through close control of air/gas ratio, furnace atmosphere, and furnace pressure-all contributing to
Contact SellerAsk for best deal
Get Latest PriceRequest a quote

Axis Thermal Engineering Company

New Siddhapudur, Coimbatore, Tamil Nadu
4.5 /5
★★★★★
★★★★★
★★★★★
★★★★★
Rating 4.5 out of 5
This is an average seller rating received from buyers based on-
  • Communication: Quick reply to buyer's enquiry and follow ups
  • Conduct: Politeness while dealing with buyer
  • Quality: Good quality products and services as per commitment
  • Experience: Timely delivery, after sales service and resolution to queries
View Mobile Number 74% Response Rate
Call +91-8043043112 74% Response Rate
TrustSEAL Verified
Manufacturer
Company Video
Ask for more details from the seller
Contact Seller

Product Details

Product Description

FIRE ALL GAS BURNER – 1514

These hardy nozzle-mix burners have been used for many years on high temperature furnaces such as those for forging steel, melting aluminum or brass, and reheating steel bars or ingots… and on low temperature ovens and air heaters. Their sealed-in construction allows maximum efficiency through close control of air/gas ratio, furnace atmosphere, and furnace pressure-all contributing to better product quality. 1514 Fire all burners, as the name suggests, are appropriate for an extensive industrial heating applications. Nominal capacities range from 3 to 84 mkcal/hr.

COMBUSTION PERFORMANCE

2514 Burners are better with 200% or more excess air. They may also be operated with excess fuel without forming carbon if additional combustion air is available in the furnace near the burner. Excess fuel limit with heavy oil is 50% as atomization deteriorates at richer ratios. Burners can be turned down to atomizing air only, but stability limits vary depending on burner size, grade of oil, and furnace atmosphere. For prolonged operation on atomizing air only in furnaces over 1200°C specify an alloy burner nose. Burners are suitable for some preheated combustion air applications (up to 350°c). Oil viscosity at the burners should not exceed 90 seconds R.W.1; oil pressure at the Ratiotrol should be between 25 and 30psi. Minimum atomizing air pressure at the burner is 24’ wg for light oil, 42” wg for heavy oil.

BURNER BLOCKS/ INSTALLATION

Burner blocks are cast refractory rated foe 1500°C furnace temperature. They are replaceable in the field, except for the 1514-10A whose mounting must be returned to the factory fir burner block replacement (or purchase a spare mounting plate with a burner block cast onto it). Burner blocks should be supported securely in the furnace wall by a layer of Castable refractory (not installation) at least 9” thick all around the burner block, extending back to the furnace shell and securely anchored to it. For furnace walls thicker than the length of the burner block, the tunnel beyond the end of the burner block should be flared 30-45° from the centerline, starting at the OD< of the burner block.

 

JACKETED BURNER BLOCK. 1514 Burner are available with support jackets around the burner block for applications where the burner block is not supported by furnace refractory. Jackets are available in three difference metals and have maximum temperature ratings for each. They must be protected with sufficient insulation so as not to exceed rated temperature. Maximum temperature rating for jacket metals depends upon frequency of heat-up/cool-down cycles. As an example, batch annealing furnaces that are heated and cooled every day should use the “intermittent exposure” ratings. Continuous annealing furnaces that remain at the same temperature for months at a time, can use the higher” continuous:” ratings.

FLAME SUPERVISION

Flame safeguards are recommended for all installations. An ultraviolet cell will monitor pilot or main flame. Pilots must be interrupted after a preset ignition period (usually 15 seconds) so flame detectors monitor main flame only.

WORKING NATURE

Control: Normally, air primary with a cross-connected, pressure balance regulator turndown, use a (biased) regulator, or throttle gas only. To protect burner from heat damage, do not set air below 2” wg in an 850°C furnace, or below 3” wg at 1000°C (whether gas is on or off). Gas pressure requirement. About 2” wg at the burner for natural gas on stoichiometric ratio; about 1/5 of the air pressure for oven gas. Preheated air: 1514 Burners are suitable for some applications with air preheated to 400°C.


Additional Information

Item Code 1514
Interested in this product?Get Latest Price from the seller
Contact Seller

Product Image

Fire All Gas Burner

Company Details


About the Company

Year of Establishment1999
Legal Status of FirmIndividual - Proprietor
Nature of BusinessManufacturer
Number of EmployeesUpto 10 People
Annual TurnoverRs. 1 - 2 Crore
IndiaMART Member SinceApr 2009
GST33AOUPD5631A1ZB
Import Export Code (IEC)3208020490

Axis Thermal Engineering Company is a prominent organization in industry known to offer a high quality range of products for heating requirements. Based in Coimbatore, Tamil Nadu (India), our company is executing its entire business activities as a SoleProprietorship based business since its establishment in the year 1999. As we are a leading manufacturer, supplier and exporter in industry, we offer products like Fuel Burner, Gas Burner, Fuel Fired Furnace, Electric Furnace, Bakery Oven and many more to our valued customers. Manufactured by using best quality resources and modern technology, our offered products are in huge demand amongst our valued customers. All our offered products are tested on various stringent parameters of quality and we ensure our customers of reliability about our rendered services. Clients can make payment as per their convenience as we have introduced a flexible terminal to receive payments.

Company Video

Send your enquiry to this supplier
I agree to the terms and privacy policy

Seller Contact Details

K. Seenuvasan

105- C, Sanganoor Road, Ganapathy
New Siddhapudur
Coimbatore - 641006, Tamil Nadu, India

Get Directions
View Mobile No.
Call +91-8043043112
Send SMS
Send Email
Tell us what you
need
Receive seller
details
Seal the deal
Pay with IndiaMART
Save time! Get Best Deal
I agree to the terms and privacy policy



X
Hi
I agree to the terms and privacy policy
Verifying...
1

Have a requirement?
Get Best Price

Hi
I agree to the terms and privacy policy
Verifying...
1

Have a requirement?
Get Best Price