Quantum Instruments And Solutions

• Brand: SINO
• Model Number: KA300
• Measuring Lengths: from 70mm to 1020mm
• Cross Section:25mm*34mm
• Reference Point: in every 50mm
• Max Running Speed:60m/Min
• Protection Level: IP53
• Resolution:0.5μm/1μm/5μm
• Outputs Signals:5V TTL (by default) / 5V RS422

QIS offer Autonics Counter/Timer;
Available to set 6 digits(0.00001 to 999999) prescale value(4digit : 0.001 to 9999)
Built-in Modbus communication function(Communication model)
Available to set the One-Shot output time in 10ms.(0.01sec. to 99.99sec.)
Increase contact capacity to 5A(CTS, CTM Series)
Available to set Count Start Point.(Initial value)
Improved to select memory protection function in the indicator
Added BATCH counter function(CTM Series)
Added Counter Up-1 / Up-2 / Down-1 / Down-2 input modes
Added Counter TOTAL / HOLD operation modes in the indicator
Added Timer TOTAL / HOLD / On Time Display operation modes in the indicator
Added Timer INT2 / NFD / NFD.1 / INTG output modes
Added Timer range 999.999s / 9999m59 / 99999.9h

• Robust, High Resolution, Accurate Micro-Controller Based Design
• Slim size of 35mm for Single and Dual Outputs
• Versions Available for Variety of Input and Output Types
• Optional, 24VDC/30mA Excitation Supply for Transmitter. Isolated from Power, OP1 & OP2
• 1.5KV AC Isolation between Power Supply, Input, OP1 & OP2 (OP2 available in ISOSIG-35D model)
• High Resolution Input : 16-bit Resolution ADC
• High Resolution Output : 10,000 parts
• Programmable Burnout (Scale Up / Scale Down)
• Front Panel Zero / Span Adjustment through Multi-turn Trim-Pots
• Programmable Zero Offset for RTD / Thermocouple Inputs
• In-built Lead Resistance Compensation for RTD Inputs
• In-built Cold Junction Compensation for Thermocouple Inputs
• Versions Available for AC (85~265 VAC) & DC (20~32 VDC) Supply
• Din-Rail Mounting : 35(W) X 75(H) X 107(D)

• 12 Digital Output Channels
• Sink Output Version :
  Open Drain : 5 to 30 V, 200 mA max.
• Source Output Version :
  VCC : 5 to 30VDC, 100mA per Channel
• Supports Discrete Coil (Bits) & Input Register (Bit-Mapped) Modbus Data Type for Status Reading
• 3 Digital Output Function Modes
  • On-Off
  • Re-Triggerable Single Pulse with Programmable Pulse-ON Time
  • Continuous Pulse Train with Programmable Pulse-ON & Pulse-OFF Time
• Programmable Fail-Safe Output States Against Communication Link Failure
• 2-wire, Half-Duplex, Start-Stop Synchronized, isolated RS485 Serial Port with Industry Standard Modbus RTU Protocol
• Programmable Slave ID, Baud Rate & Parity
• Compact DIN-Rail Mount Enclosure : 22.5(W) X 101(H) X 119(D), mm
• Wide Supply Voltage Range : 18 ~ 32 VDC (24 VDC Nominal)

FEATURES

Sensorless Vector Micro AC Drive. The compact design is ideal for small and medium horsepower applications. The M drive is designed to provide an ultra-low-noise operation, and includes several innovative technologies that reduce interference.

Details :

• Adjustable V/f curve and vector control
• Carrier frequency up to 15 kHz
• Auto torque boost & slip compensation
• Built-in PID feedback control
• Built-in MODBUS communication, baud rate up to 38400 bps
• 0 speed holding function
• Built-in sleep / revival function
• Support communication module (DN-02, LN-01, PD-01)

APPLICATIONS

The 4-channel relay module features visualization of four switching states through LEDs. The relay outputs are each equipped with an AC 230V/3A changeover contact. A removable terminal strip with push-in technology is available for each channel. This saves you time while ensuring reliable wiring.

• Low cost, Effective, Easy to use Push wheel based Digital timer
• 3-Digits, Single Row Display
• Programmable timer start modes to suit various applications
• Programmable ON Delay/Interval mode
• Programmable Up/Down counting
• Programmable Auto Reset/Latch Output
• Programmable Front Reset
• Programmable Memory Backup
• Programmable Output 2 functions: Auxiliary contact/End of cycle/Instant contact
• High Accuracy: 0.05% of Full scale (Repeat Accuracy: 0.01%)
• Multiple Time Range: From 0.01 Sec to 999 Hrs
• Time base selection via key board
• Time Setting via High Quality Push wheel switches
• Configuration at power on (To prevent unauthorized tampering)
• Universal supply voltage ranges from 90 To 270 VAC
• Available in 3 Standard DIN sizes

• PLC logic development
• System migration
• System Detailed Engineering
• HMI development
• Networking
• SCADA software development.
• Site trouble shooting and upgradation of existing systems.

• Without heat sink

JUMO TYA-432 thyristor power switch (709020)

• Single phase, 3 phase version
• With heat sink

• Measure each phase voltage/ampere of 3 phase electricity
• 3 lines 4 digit LED display, easy to read
• With two alarm output, easy & useful to monitor each phase
• Some model with 4-20mA transform current output and RS485 communication function

Additional Information:

• Item Code: DS-Series